Tanja Franken
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Tanja Franken has a total of 104 co-authors. Here are the top co-authors by number of shared publications:
Dennis Weber
Technische Chemie 1 Technische Universität Darmstadt Peter‐Grünberg‐Straße 8 64287 Darmstadt Germany
5 shared publications- Regina Palkovits
Chair of Heterogeneous Catalysis and Technical Chemistry, Institute of Technical and Macromolecular Chemistry, RWTH Aachen University, Worringerweg 2, 52074 Aachen, Germany
4 shared publications - Andre Heel
Winterthur museum garden and library
3 shared publications - Bastian J. M. Etzold
Department of Chemistry Ernst-Berl-Institute for Technical and Macromolecular Chemistry Technical University of Darmstadt 64287 Darmstadt Germany
3 shared publications Danny Stark
Technische Universität Darmstadt Peter-Grünberg-Straße 8
3 shared publicationsAlfons Drochner
Technische Universität Darmstadt Peter-Grünberg-Straße 8
2 shared publications
Latest Publications
- Open Access
- 18 September 2026
- Published by Wiley in Advanced Energy and Sustainability Research
- Vol. 7 (9) , e70276
Nanocrystalline Iridium Oxide Stabilized by Magnesium–Titanium–Spinel as Active Acidic Oxygen Evolution Reaction Catalyst
Hydrogen produced by proton exchange water electrolysis (PEM‐WE) is crucial in storing and transporting green energy from renewable resources. However, broad application of PEM‐WE technology is hindered by the necessity of scarce and expensive iridium oxide needed to catalyze the sluggish oxygen evolution reaction on the anode. A reduction of iridium loading can be achieved by using mixed metal oxides. Herein, we show an iridium–magnesium–titanium spinel with a threefold increase in mass specific iridium activity compared to commercial iridium oxide. We report the strong influence of iridium content on the intrinsic activity and the necessity of soft calcination conditions to obtain a highly active catalyst. The observed high activity is contributed to finely dispersed nanosized iridium clusters in the transitional state from amorphous to crystalline iridium oxide interacting with the underlying mixed metal oxide.
- 18 September 2026
- Published by Wiley in Advanced Energy and Sustainability Research
- Vol. 7 (9) , e70276
Open AccessNanocrystalline Iridium Oxide Stabilized by Magnesium–Titanium–Spinel as Active Acidic Oxygen Evolution Reaction Catalyst
Hydrogen produced by proton exchange water electrolysis (PEM‐WE) is crucial in storing and transporting green energy from renewable resources. However, broad application of PEM‐WE technology is hindered by the necessity of scarce and expensive iridium oxide needed to catalyze the sluggish oxygen evolution reaction on the anode. A reduction of iridium loading can be achieved by using mixed metal oxides. Herein, we show an iridium–magnesium–titanium spinel with a threefold increase in mass specific iridium activity compared to commercial iridium oxide. We report the strong influence of iridium content on the intrinsic activity and the necessity of soft calcination conditions to obtain a highly active catalyst. The observed high activity is contributed to finely dispersed nanosized iridium clusters in the transitional state from amorphous to crystalline iridium oxide interacting with the underlying mixed metal oxide.
- 26 August 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 65 (35) , 18738-18747
Identifying the Rate-Determining Step of the Oxidative Dehydrogenation of Ethanol on Iron Molybdate Catalysts through Isotope Exchange Experiments
The oxidative dehydrogenation (ODH) of ethanol (EtOH) to acetaldehyde (AcH) represents a promising route for the upgrading of bioethanol into value-added chemicals. Iron molybdate catalysts, widely used in the industrial oxidation of methanol to formaldehyde, have also shown high activity and selectivity for the ODH of EtOH. However, the reaction mechanism on these catalysts remains to be fully elucidated. In this study, isotope exchange experiments with selectively deuterated EtOH isotopologues (CH3CH2OD, CH3CD2OH, and CD3CH2OH) were used to identify the rate-determining step (RDS) of EtOH ODH on Fe2(MoO4)3. No kinetic isotope effect was observed when the hydroxyl hydrogen or the C2 hydrogen atoms were replaced by deuterium, indicating that O–H and C2–H bond cleavages are not rate-determining. In contrast, substitution of the C1 hydrogen atoms resulted in a pronounced primary kinetic isotope effect (kH/kD ≈ 2.5), demonstrating that C1–H bond cleavage constitutes the rate-determining step in AcH formation. Additional hydrogen–deuterium exchange reactions involving EtOH, AcH, and water were identified by mass spectrometry and confirmed by 2H NMR spectroscopy. These findings establish the mechanism of C–H activation and clarify the nature of the rate-determining step during the ODH of EtOH on iron molybdate catalysts.
- 26 August 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 65 (35) , 18738-18747
Identifying the Rate-Determining Step of the Oxidative Dehydrogenation of Ethanol on Iron Molybdate Catalysts through Isotope Exchange Experiments
The oxidative dehydrogenation (ODH) of ethanol (EtOH) to acetaldehyde (AcH) represents a promising route for the upgrading of bioethanol into value-added chemicals. Iron molybdate catalysts, widely used in the industrial oxidation of methanol to formaldehyde, have also shown high activity and selectivity for the ODH of EtOH. However, the reaction mechanism on these catalysts remains to be fully elucidated. In this study, isotope exchange experiments with selectively deuterated EtOH isotopologues (CH3CH2OD, CH3CD2OH, and CD3CH2OH) were used to identify the rate-determining step (RDS) of EtOH ODH on Fe2(MoO4)3. No kinetic isotope effect was observed when the hydroxyl hydrogen or the C2 hydrogen atoms were replaced by deuterium, indicating that O–H and C2–H bond cleavages are not rate-determining. In contrast, substitution of the C1 hydrogen atoms resulted in a pronounced primary kinetic isotope effect (kH/kD ≈ 2.5), demonstrating that C1–H bond cleavage constitutes the rate-determining step in AcH formation. Additional hydrogen–deuterium exchange reactions involving EtOH, AcH, and water were identified by mass spectrometry and confirmed by 2H NMR spectroscopy. These findings establish the mechanism of C–H activation and clarify the nature of the rate-determining step during the ODH of EtOH on iron molybdate catalysts.
- Open Access
- 6 August 2026
- Published by Elsevier in Chemical Engineering Journal Advances
- Vol. 27
Exploring the potential of dynamic periodic operation on tackling challenging reactions under traditional steady state - a review
- 6 August 2026
- Published by Elsevier in Chemical Engineering Journal Advances
- Vol. 27
Open AccessExploring the potential of dynamic periodic operation on tackling challenging reactions under traditional steady state - a review
- Open Access
- 14 January 2026
- Published by Wiley in ChemCatChem
- Vol. 18 (1)
Probing the Selectivity of Acidic Sites in the Oxidative Catalysis of Ethanol: Al x Fe 2 − x (MoO 4 ) 3
We report the catalytic reactions of ethanol under oxidizing conditions using ball‐milled Al x Fe 2− x (MoO 4 ) 3 (0.25⩽ x Al ⩽1.0) samples of similar particle sizes and surface areas. Characteristic of this series is the increased Mo:(Al+Fe) ratio of 1.7:1.0 in surface near volumes of the bulk. Acetaldehyde (AcH) results from the oxidative dehydrogenation of ethanol as the main product. The selectivity of AcH decreases by about 20% around 250°C in favor of diethyl ether (DEE), regardless of the Al 3+ content. This suggests that the Lewis acidic Al 3+ cations act on the general bulk structure and, in particular, influence the lattice oxygen activity of Mo–O–Fe redox centers. At high conversion rates at elevated temperatures, the overoxidation of ethanol to CO x is reduced compared to Fe 2 (MoO 4 ) 3 in favor of the formation of ethene (dehydration of ethanol). Beyond reporting on the catalytic reactions of these compounds, we provide insights into defect sites in subsurface volumes through methods for characterizing solid‐state materials such as X‐ray powder diffraction, SEM‐EDX, 57 Fe Mössbauer spectroscopy, and thermal analysis.
- 14 January 2026
- Published by Wiley in ChemCatChem
- Vol. 18 (1)
Open AccessProbing the Selectivity of Acidic Sites in the Oxidative Catalysis of Ethanol: Al x Fe 2 − x (MoO 4 ) 3
We report the catalytic reactions of ethanol under oxidizing conditions using ball‐milled Al x Fe 2− x (MoO 4 ) 3 (0.25⩽ x Al ⩽1.0) samples of similar particle sizes and surface areas. Characteristic of this series is the increased Mo:(Al+Fe) ratio of 1.7:1.0 in surface near volumes of the bulk. Acetaldehyde (AcH) results from the oxidative dehydrogenation of ethanol as the main product. The selectivity of AcH decreases by about 20% around 250°C in favor of diethyl ether (DEE), regardless of the Al 3+ content. This suggests that the Lewis acidic Al 3+ cations act on the general bulk structure and, in particular, influence the lattice oxygen activity of Mo–O–Fe redox centers. At high conversion rates at elevated temperatures, the overoxidation of ethanol to CO x is reduced compared to Fe 2 (MoO 4 ) 3 in favor of the formation of ethene (dehydration of ethanol). Beyond reporting on the catalytic reactions of these compounds, we provide insights into defect sites in subsurface volumes through methods for characterizing solid‐state materials such as X‐ray powder diffraction, SEM‐EDX, 57 Fe Mössbauer spectroscopy, and thermal analysis.
- Open Access
- 29 October 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Gas-Phase Raman Spectroscopy for Two-Dimensional Temperature and Concentration Profiling in the Catalytic Oxidative Dehydrogenation of Ethanol
A novel optically accessible catalysis flow channel (CFC) is introduced that enables quantitative, contiguous, two-dimensional in situ measurements of gas-phase temperature and species con- centrations during heterogeneous catalytic reactions. Spatially resolved gas-phase Raman spec- troscopy, integral Fourier-transform infrared spectroscopy (FTIR) spectroscopy, and catalyst- resolved infrared (IR) thermography establish a well-defined platform for studying coupled reaction–transport phenomena. Applied to the oxidative dehydrogenation (ODH) of ethanol (EtOH) over iron–molybdenum (Fe–Mo) oxide catalysts, spontaneous Raman measurements yielded two-dimensional profiles of nine gas-phase species—with limits of detection (LODs) in the tens-to-hundreds-of-ppm range—and gas-phase temperature within 500 μm of the catalyst surface. Transport analysis in the boundary layer yielded a Lewis number of approximately 1.65, indicating dominant thermal diffusion near the surface, while axial Péclet numbers revealed diffusion-controlled heat transport but advection-dominated product transport in a laminar regime. Varying the bulk flow velocity did not significantly alter conversion or product distributions, indicating kinetic and diffusive control under the present conditions. An iron- rich catalyst formulation exhibited higher activity than stoichiometric Fe2(MoO4)3, whereas temperatures above 511 K reduced selectivity due to increased formation of total-oxidation prod- ucts. Catalyst-free experiments, supported by kinetic simulations, confirmed partial gas-phase oxidation of acetaldehyde (AcH) to CO, CO2, acetic acid (AcOH), methanol, formaldehyde, and peracetic acid. These results highlight the importance of local gas-phase contributions and demonstrate that spatially resolving the gas-phase thermochemistry enables the gas phase to act as a reporter of surface reactions and facilitates the decoupling of chemical processes from transport phenomena.
- 29 October 2025
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessGas-Phase Raman Spectroscopy for Two-Dimensional Temperature and Concentration Profiling in the Catalytic Oxidative Dehydrogenation of Ethanol
A novel optically accessible catalysis flow channel (CFC) is introduced that enables quantitative, contiguous, two-dimensional in situ measurements of gas-phase temperature and species con- centrations during heterogeneous catalytic reactions. Spatially resolved gas-phase Raman spec- troscopy, integral Fourier-transform infrared spectroscopy (FTIR) spectroscopy, and catalyst- resolved infrared (IR) thermography establish a well-defined platform for studying coupled reaction–transport phenomena. Applied to the oxidative dehydrogenation (ODH) of ethanol (EtOH) over iron–molybdenum (Fe–Mo) oxide catalysts, spontaneous Raman measurements yielded two-dimensional profiles of nine gas-phase species—with limits of detection (LODs) in the tens-to-hundreds-of-ppm range—and gas-phase temperature within 500 μm of the catalyst surface. Transport analysis in the boundary layer yielded a Lewis number of approximately 1.65, indicating dominant thermal diffusion near the surface, while axial Péclet numbers revealed diffusion-controlled heat transport but advection-dominated product transport in a laminar regime. Varying the bulk flow velocity did not significantly alter conversion or product distributions, indicating kinetic and diffusive control under the present conditions. An iron- rich catalyst formulation exhibited higher activity than stoichiometric Fe2(MoO4)3, whereas temperatures above 511 K reduced selectivity due to increased formation of total-oxidation prod- ucts. Catalyst-free experiments, supported by kinetic simulations, confirmed partial gas-phase oxidation of acetaldehyde (AcH) to CO, CO2, acetic acid (AcOH), methanol, formaldehyde, and peracetic acid. These results highlight the importance of local gas-phase contributions and demonstrate that spatially resolving the gas-phase thermochemistry enables the gas phase to act as a reporter of surface reactions and facilitates the decoupling of chemical processes from transport phenomena.
- Open Access
- 14 October 2025
- Published by Wiley in ChemCatChem
- Vol. 17 (23)
A Design of Experiment‐Driven Optimization of NiMnAl Mixed Metal Oxide Catalysts for CO 2 Methanation
Power‐to‐gas technologies, including CO 2 methanation, offer a promising strategy for mitigating anthropogenic climate change. Nickel‐based mixed metal oxide catalysts have demonstrated high activity, selectivity and stability in this challenging reaction in recent years. This study investigates the effects of synthesis parameters on the structure, activation, and reaction behavior of NiMnAl mixed metal oxide (MMO) catalysts. A Design of Experiment approach was employed to systematically vary the calcination temperature (500–950 °C), pH (8–10), and aging time (1–30 h) during synthesis by coprecipitation, resulting in the synthesis and testing of approximately 35 catalysts. The calcination temperature determines the catalyst structure, with metastable NiAl phases forming up to 650 °C and spinel phases forming above 800 °C. Notably, the spinel NiMnAl MMO catalysts exhibit superior performance, achieving approximately 60% higher methane formation rates per gram Ni of the catalyst compared to a supported industrial methanation reference catalyst (SPP2080‐IMRC). Comprehensive characterization using XRD, elemental analysis, N 2 physisorption, TPR, CO 2 ‐TPD, N 2 O chemisorption, and STEM‐EDXS provide insights into the catalysts' properties and activity.
- 14 October 2025
- Published by Wiley in ChemCatChem
- Vol. 17 (23)
Open AccessA Design of Experiment‐Driven Optimization of NiMnAl Mixed Metal Oxide Catalysts for CO 2 Methanation
Power‐to‐gas technologies, including CO 2 methanation, offer a promising strategy for mitigating anthropogenic climate change. Nickel‐based mixed metal oxide catalysts have demonstrated high activity, selectivity and stability in this challenging reaction in recent years. This study investigates the effects of synthesis parameters on the structure, activation, and reaction behavior of NiMnAl mixed metal oxide (MMO) catalysts. A Design of Experiment approach was employed to systematically vary the calcination temperature (500–950 °C), pH (8–10), and aging time (1–30 h) during synthesis by coprecipitation, resulting in the synthesis and testing of approximately 35 catalysts. The calcination temperature determines the catalyst structure, with metastable NiAl phases forming up to 650 °C and spinel phases forming above 800 °C. Notably, the spinel NiMnAl MMO catalysts exhibit superior performance, achieving approximately 60% higher methane formation rates per gram Ni of the catalyst compared to a supported industrial methanation reference catalyst (SPP2080‐IMRC). Comprehensive characterization using XRD, elemental analysis, N 2 physisorption, TPR, CO 2 ‐TPD, N 2 O chemisorption, and STEM‐EDXS provide insights into the catalysts' properties and activity.
- Open Access
- 29 September 2025
- Published by Royal Society of Chemistry (RSC) in EES Catalysis
- Vol. 4 (1) , 118-133
Phosphate modification of Pd/Al 2 O 3 enhances activity and stability in aromatic hydrogenation under CO-contaminated hydrogen
A phosphate modification strategy enhances the dispersion and thermal stability of Pd nanoparticles supported on Al 2 O 3 , while enabling efficient aromatic hydrogenation under hydrogen streams containing CO impurities.
- 29 September 2025
- Published by Royal Society of Chemistry (RSC) in EES Catalysis
- Vol. 4 (1) , 118-133
Open AccessPhosphate modification of Pd/Al 2 O 3 enhances activity and stability in aromatic hydrogenation under CO-contaminated hydrogen
A phosphate modification strategy enhances the dispersion and thermal stability of Pd nanoparticles supported on Al 2 O 3 , while enabling efficient aromatic hydrogenation under hydrogen streams containing CO impurities.
- Open Access
- 22 September 2025
- Published by Elsevier in Applied Catalysis A: General
- Vol. 708
Revealing the characteristics of supported Ni-Mn based mixed metal oxide catalysts: Operando insights into their activation and CO2 methanation behavior
- 22 September 2025
- Published by Elsevier in Applied Catalysis A: General
- Vol. 708
Open AccessRevealing the characteristics of supported Ni-Mn based mixed metal oxide catalysts: Operando insights into their activation and CO2 methanation behavior
- Open Access
- 27 August 2025
- Published by American Chemical Society (ACS) in ACS ES&T Engineering
- Vol. 5 (11) , 2936-2948
Toward Improved Exhaust Emission Control of Stoichiometric Engines by Intentional Oxygen Dithering
- 27 August 2025
- Published by American Chemical Society (ACS) in ACS ES&T Engineering
- Vol. 5 (11) , 2936-2948
Open AccessToward Improved Exhaust Emission Control of Stoichiometric Engines by Intentional Oxygen Dithering
- Open Access
- 5 August 2025
- Published by Wiley in ChemCatChem
- Vol. 17 (19)
Finding the Right Synergy of Iron and Molybdenum in Mixed Metal Oxide Catalysts for the Sustainable Production of Acetaldehyde via Oxidative Dehydrogenation of Ethanol
Iron–molybdenum mixed oxides are well‐established catalysts for the oxidative dehydrogenation (ODH) of methanol, but their performance in the ODH of ethanol (EtOH), particularly with respect to the Mo:Fe ratio, remains unexplored. In this study, we present the synthesis of mixed oxides across the full composition range, their catalytic assessment in the ODH of EtOH, and their structural characterization. While pure iron oxide is unselective toward acetaldehyde (AcH), introducing small amounts of molybdenum oxide enhances the catalyst's selectivity significantly. In contrast, molybdate‐rich systems tend to produce more dehydration products such as diethyl ether and ethene due to an increased acid site density. The optimal catalyst was found to be an iron‐rich system with a composition of xFe = 0.95, yielding 94% AcH at temperatures as low as 220 °C with promising long‐term stability. Therefore, while molybdenum is essential for high catalytic activity and selectivity, only small amounts are required when supported by a high surface area, defect‐rich iron oxide, highlighting the efficiency of this mixed oxide system as catalyst for the ODH of EtOH.
- 5 August 2025
- Published by Wiley in ChemCatChem
- Vol. 17 (19)
Open AccessFinding the Right Synergy of Iron and Molybdenum in Mixed Metal Oxide Catalysts for the Sustainable Production of Acetaldehyde via Oxidative Dehydrogenation of Ethanol
Iron–molybdenum mixed oxides are well‐established catalysts for the oxidative dehydrogenation (ODH) of methanol, but their performance in the ODH of ethanol (EtOH), particularly with respect to the Mo:Fe ratio, remains unexplored. In this study, we present the synthesis of mixed oxides across the full composition range, their catalytic assessment in the ODH of EtOH, and their structural characterization. While pure iron oxide is unselective toward acetaldehyde (AcH), introducing small amounts of molybdenum oxide enhances the catalyst's selectivity significantly. In contrast, molybdate‐rich systems tend to produce more dehydration products such as diethyl ether and ethene due to an increased acid site density. The optimal catalyst was found to be an iron‐rich system with a composition of xFe = 0.95, yielding 94% AcH at temperatures as low as 220 °C with promising long‐term stability. Therefore, while molybdenum is essential for high catalytic activity and selectivity, only small amounts are required when supported by a high surface area, defect‐rich iron oxide, highlighting the efficiency of this mixed oxide system as catalyst for the ODH of EtOH.