Chayut Nuntadusit
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chayut Nuntadusit has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Natthaporn Kaewchoothong
Department of Mechanical and Mechatronics Engineering, Faculty of Engineering, Prince of Songkla University
4 shared publications Chattawat Aroonrujiphan
Department of Mechanical Engineering, Faculty of Engineering, Prince of Songkla University, Hatyai, Songkhla 90110, Thailand
2 shared publications- Surapong Chatpun
Prince of Songkla University
2 shared publications - Ibroheng Piya
Department of Mechanical and Mechatronics Engineering, Faculty of Engineering, Prince of Songkla University, Hat Yai 90110, Songkhla, Thailand
1 shared publication Kenichiro Takeishi
Tokushima Bunri University
1 shared publicationKittinan Maliwan
Prince of Songkla University
1 shared publication
Latest Publications
- Open Access
Thermal and Flow Characteristics of Perforated Blockages in Confined Channels
Heat transfer, friction, and thermal performance of perforated flow blockages are measured in a confined rectangular channel (W/H = 9.375, Re = 7700–12,200). Wall temperature fields are measured by thermochromic liquid crystal thermography. Flow structures are computed with SST k–ω RANS simulations (grid convergence index 7.1%). Twelve configurations at an equal open-area ratio of 27.6%—compared at matched open-area for the first time—cover single-row and double-row perforations, inline and staggered alignments at P = 1H–3H. Four flow regimes are identified: direct jet penetration, recirculating wake, merging-zone interaction, and extended reattachment. Single-row staggered blockages at P = 1H give the highest enhancement, ≈ 5–6. The double-row geometry (smaller holes in two rows at constant open-area) reduces the friction factor by more than 50% and reaches the maximum thermal performance factor, η ≈ 1.3–1.4, for the inline arrangement at P = 1H. Configurations that maximize also maximize the Nusselt number uniformity index, applied here to perforated blockages for the first time, . remains below 40% for all configurations. Double-row arrangements at P = 2H give the best balance of η and . A regime map summarizes these results for configuration selection in aero-engine internal cooling and related confined-channel systems.Open AccessThermal and Flow Characteristics of Perforated Blockages in Confined Channels
Heat transfer, friction, and thermal performance of perforated flow blockages are measured in a confined rectangular channel (W/H = 9.375, Re = 7700–12,200). Wall temperature fields are measured by thermochromic liquid crystal thermography. Flow structures are computed with SST k–ω RANS simulations (grid convergence index 7.1%). Twelve configurations at an equal open-area ratio of 27.6%—compared at matched open-area for the first time—cover single-row and double-row perforations, inline and staggered alignments at P = 1H–3H. Four flow regimes are identified: direct jet penetration, recirculating wake, merging-zone interaction, and extended reattachment. Single-row staggered blockages at P = 1H give the highest enhancement, ≈ 5–6. The double-row geometry (smaller holes in two rows at constant open-area) reduces the friction factor by more than 50% and reaches the maximum thermal performance factor, η ≈ 1.3–1.4, for the inline arrangement at P = 1H. Configurations that maximize also maximize the Nusselt number uniformity index, applied here to perforated blockages for the first time, . remains below 40% for all configurations. Double-row arrangements at P = 2H give the best balance of η and . A regime map summarizes these results for configuration selection in aero-engine internal cooling and related confined-channel systems. - Open Access
- 18 December 2025
- Published by MDPI AG in Bioengineering
- Vol. 12 (12) , 1380
Using Patient-Based Computational Fluid Dynamics for Abdominal Aortic Aneurysm Assessment
Abdominal aortic aneurysm (AAA) is a dangerous disease and can cause sudden death if it ruptures. This study investigated blood flow behaviors and hemodynamic changes in three categories (small, medium and large diameters) of AAAs using computational fluid dynamics (CFD) based on patient geometry. Computed tomography images of patients with abdominal aortic aneurysms were used to construct a patient-specific AAA model. This study included one healthy subject and seven patients who had AAAs with a diameter larger than 3 cm. The results showed that the aortic aneurysms were highly turbulent in the diastolic phase, and there was an increase in turbulence as the aneurysm size increased. The time-averaged wall shear stress (TAWSS) in the artery was high at peak systole and decreased during diastole. The oscillating shear index (OSI) was higher at the middle and distal aortic aneurysm sac than in other areas. Low TAWSS and a high OSI in the aneurysm region may indicate a risk of wall rupture in AAA. This study suggests that CFD provides further insights by visualizing blood flow behaviors and quantitatively analyzing hemodynamic parameters.
- 18 December 2025
- Published by MDPI AG in Bioengineering
- Vol. 12 (12) , 1380
Open AccessUsing Patient-Based Computational Fluid Dynamics for Abdominal Aortic Aneurysm Assessment
Abdominal aortic aneurysm (AAA) is a dangerous disease and can cause sudden death if it ruptures. This study investigated blood flow behaviors and hemodynamic changes in three categories (small, medium and large diameters) of AAAs using computational fluid dynamics (CFD) based on patient geometry. Computed tomography images of patients with abdominal aortic aneurysms were used to construct a patient-specific AAA model. This study included one healthy subject and seven patients who had AAAs with a diameter larger than 3 cm. The results showed that the aortic aneurysms were highly turbulent in the diastolic phase, and there was an increase in turbulence as the aneurysm size increased. The time-averaged wall shear stress (TAWSS) in the artery was high at peak systole and decreased during diastole. The oscillating shear index (OSI) was higher at the middle and distal aortic aneurysm sac than in other areas. Low TAWSS and a high OSI in the aneurysm region may indicate a risk of wall rupture in AAA. This study suggests that CFD provides further insights by visualizing blood flow behaviors and quantitatively analyzing hemodynamic parameters.
- Open Access
- 17 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (4) , 2113
Computational Study of Abdominal Aortic Aneurysms with Severely Angulated Neck Based on Transient Hemodynamics Using an Idealized Model
An abdominal aortic aneurysm (AAA) is an enlargement of the abdominal aorta that can become a life-threatening disease. The pulsatile blood flow exhibits intricate laminar patterns in the abdominal portion of the human aorta under normal resting conditions, whereas secondary flows are caused by adjacent branches and abnormal vessel geometries. If a pathological disorder (e.g., aneurysm) alters the structural composition of the artery wall, the flow dynamics become more complex. In this study, we analyzed the hemodynamics of pulsatile blood flow in three-dimensional AAA models. Computational predictions of hemodynamic changes were performed considering idealized models for four severe proximal neck angulations of symmetric aneurysms assuming conditions of laminar flow and a rigid artery wall. The predictions were based on computational fluid dynamics throughout the cardiac cycle. Postprocessing was used to visualize the numerical findings. The hemodynamic changes in factors such as velocity, flow streamline, pressure, and wall shear stress were obtained and visualized. The resulting blood flow through the severely angulated proximal neck of the abdominal aorta caused strong turbulence and asymmetric flow inside the aneurysm sac, leading to blood recirculation, especially during diastole. The simulation results showed the formation of regions with high and low wall shear stress, turbulent flow, and recirculation in the aneurysm sac depending on the angulation, which could have led to aortic wall weakness.
- 17 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (4) , 2113
Open AccessComputational Study of Abdominal Aortic Aneurysms with Severely Angulated Neck Based on Transient Hemodynamics Using an Idealized Model
An abdominal aortic aneurysm (AAA) is an enlargement of the abdominal aorta that can become a life-threatening disease. The pulsatile blood flow exhibits intricate laminar patterns in the abdominal portion of the human aorta under normal resting conditions, whereas secondary flows are caused by adjacent branches and abnormal vessel geometries. If a pathological disorder (e.g., aneurysm) alters the structural composition of the artery wall, the flow dynamics become more complex. In this study, we analyzed the hemodynamics of pulsatile blood flow in three-dimensional AAA models. Computational predictions of hemodynamic changes were performed considering idealized models for four severe proximal neck angulations of symmetric aneurysms assuming conditions of laminar flow and a rigid artery wall. The predictions were based on computational fluid dynamics throughout the cardiac cycle. Postprocessing was used to visualize the numerical findings. The hemodynamic changes in factors such as velocity, flow streamline, pressure, and wall shear stress were obtained and visualized. The resulting blood flow through the severely angulated proximal neck of the abdominal aorta caused strong turbulence and asymmetric flow inside the aneurysm sac, leading to blood recirculation, especially during diastole. The simulation results showed the formation of regions with high and low wall shear stress, turbulent flow, and recirculation in the aneurysm sac depending on the angulation, which could have led to aortic wall weakness.
- Open Access
- 7 November 2020
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 77 (1) , 11-23
Effect of Pulsating Flame Jet on Flow and Heat Transfer Characteristics
This research aims to study the effect of pulsating frequency on flame structure and heat transfer characteristics of premixed flame from a pipe nozzle. The LPG and air were used as gas fuel and oxidizer. The equivalence ratios ( ) were evaluated at 0.8, 1.0, and 1.2 under a constant Reynolds number Re = 500. The effect of nozzle-to-impingement surface distance ratio was investigated at H = 2D to 10D, here D is the nozzle diameter at 12 mm. The frequency of pulsating (f) was varied from f = 0 to 10 Hz using a solenoid valve. The flame structures of free flame jet and the impinging flame jet were recorded with a digital camera. The average heat flux on impingement surface was measured with water cooling plate and evaluated from the heat balance of the cooling water. The results show that the pulsating of flame jet become having gap on flame and the mushroom appear at the end of flame. The size of mushroom structure becomes larger when increasing the frequency. While the non-pulsating jet did not appear in this structure. Pulsating flame jet can increase the overall average heat flux on the impingement surface up to about 12% for case of = 1.2 and H = 2D and f = 10 Hz. when compared to case of f = 0 Hz.
- 7 November 2020
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 77 (1) , 11-23
Open AccessEffect of Pulsating Flame Jet on Flow and Heat Transfer Characteristics
This research aims to study the effect of pulsating frequency on flame structure and heat transfer characteristics of premixed flame from a pipe nozzle. The LPG and air were used as gas fuel and oxidizer. The equivalence ratios ( ) were evaluated at 0.8, 1.0, and 1.2 under a constant Reynolds number Re = 500. The effect of nozzle-to-impingement surface distance ratio was investigated at H = 2D to 10D, here D is the nozzle diameter at 12 mm. The frequency of pulsating (f) was varied from f = 0 to 10 Hz using a solenoid valve. The flame structures of free flame jet and the impinging flame jet were recorded with a digital camera. The average heat flux on impingement surface was measured with water cooling plate and evaluated from the heat balance of the cooling water. The results show that the pulsating of flame jet become having gap on flame and the mushroom appear at the end of flame. The size of mushroom structure becomes larger when increasing the frequency. While the non-pulsating jet did not appear in this structure. Pulsating flame jet can increase the overall average heat flux on the impingement surface up to about 12% for case of = 1.2 and H = 2D and f = 10 Hz. when compared to case of f = 0 Hz.
- 15 August 2020
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 74 (1) , 68-80
Flow and Heat Transfer Characteristics of Impinging Bubbly Jet
- 15 August 2020
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 74 (1) , 68-80
Flow and Heat Transfer Characteristics of Impinging Bubbly Jet
- 14 September 2018
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 32 (9) , 4461-4471
Effect of rotation number on flow and heat transfer characteristics in serpentine passage with ribbed walls
- 14 September 2018
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 32 (9) , 4461-4471
Effect of rotation number on flow and heat transfer characteristics in serpentine passage with ribbed walls
- 14 July 2018
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 127, 751-767
Heat transfer enhancement on a surface of impinging jet by increasing entrainment using air-augmented duct
- 14 July 2018
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 127, 751-767
Heat transfer enhancement on a surface of impinging jet by increasing entrainment using air-augmented duct