Igor Vasilevich Uskov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Igor Vasilevich Uskov has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Ivan Yurievich Gubanov
Foundry Department, School of Non-Ferrous Metals and Materials Science, Siberian Federal University, Krasnoyarsk, Russia
3 shared publications - Elena Mikhailovna Lesiv
Foundry Department, School of Non-Ferrous Metals and Materials Science, Siberian Federal University, Krasnoyarsk, Russia
2 shared publications - Yuriy Vasilievich Gorokhov
Siberian Federal University
2 shared publications - Aleksandr Aleksandrovich Kosovich
School of Non-Ferrous Metals, Siberian Federal University, 660041 Krasnoyarsk, Russia
1 shared publication I. S. Gudkov
ООО "НПЦ Магнитной гидродинамики"
1 shared publication- Igor Lazarevich Konstantinov
Siberian Federal University, Krasnoyarsk, Russian Federation
1 shared publication
Latest Publications
- 10 January 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 119 (5-6) , 3857-3863
Obtaining a low-temperature paste based on eutectic silumin for soldering special-purpose products
- 10 January 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 119 (5-6) , 3857-3863
Obtaining a low-temperature paste based on eutectic silumin for soldering special-purpose products
- 17 September 2018
- Published by Springer Nature in Metallurgist
- Vol. 62 (5-6) , 597-602
Development of Tooling and Modes of Dispersion for Powders of Solder Aluminum Alloys
- 17 September 2018
- Published by Springer Nature in Metallurgist
- Vol. 62 (5-6) , 597-602
Development of Tooling and Modes of Dispersion for Powders of Solder Aluminum Alloys
- Open Access
- 16 August 2018
- Published by National University of Science and Technology MISiS in Izvestiya Vuzov. Tsvetnaya Metallurgiya (Proceedings of Higher Schools. Nonferrous Metallurgy)
- No. 4,p. 53-59-59
EXTRUSION OF 01417 ALLOY INGOTS OBTAINED IN THE ELECTROMAGNETIC CRYSTALLIZER AT THE CONFORM UNIT
It is known that casting long ingots of small sections (∅8–12 mm) of 01417 alloy into an electromagnetic crystallizer makes it possible to obtain a dispersed structure with insignificant intradendritic segregation. Diffusion annealing of ingots (550 °C, 4–5 h holding time) eliminates intracrystalline segregation and reduces the level of internal stresses in metal thus providing the conditions for subsequent wire drawing. The paper demonstrates that high plastic deformation of ingots without diffusion annealing can be achieved by Conform continuous extrusion, which ensures high quality and geometrical accuracy of products. The analysis of various Conform units revealed an inherent weakness – the absence of connection between the system securing the fixed part of the detachable container (shoe) and the drive wheel shaft, which leads to an increased load in the operating mode. The purpose of the work was to upgrade the Conform unit by creating a connection between the shoe and the impeller shaft to obtain a high-quality billet for subsequent wire drawing of the ∅12 mm ingot cast into the electromagnetic crystallizer. An optimal temperature of ingot extrusion (300 °С) was found to eliminate the intense adhesion of wrought metal on the tool surface. The experimental ∅5 mm rod made of 01417 alloy obtained from the ∅12 mm ingot at the Conform unit features high processing ductility. This is indicated by an increase in its yield point and relative elongation. Metallographic studies demonstrated a fine-grained structure achieved in the extruded rod, which provides the conditions for subsequent wire drawing without annealing. The results of the study provide a basis for refining the process conditions of calibrated billet production on the Conform unit followed by wire drawing with required properties.
- 16 August 2018
- Published by National University of Science and Technology MISiS in Izvestiya Vuzov. Tsvetnaya Metallurgiya (Proceedings of Higher Schools. Nonferrous Metallurgy)
- No. 4,p. 53-59-59
Open AccessEXTRUSION OF 01417 ALLOY INGOTS OBTAINED IN THE ELECTROMAGNETIC CRYSTALLIZER AT THE CONFORM UNIT
It is known that casting long ingots of small sections (∅8–12 mm) of 01417 alloy into an electromagnetic crystallizer makes it possible to obtain a dispersed structure with insignificant intradendritic segregation. Diffusion annealing of ingots (550 °C, 4–5 h holding time) eliminates intracrystalline segregation and reduces the level of internal stresses in metal thus providing the conditions for subsequent wire drawing. The paper demonstrates that high plastic deformation of ingots without diffusion annealing can be achieved by Conform continuous extrusion, which ensures high quality and geometrical accuracy of products. The analysis of various Conform units revealed an inherent weakness – the absence of connection between the system securing the fixed part of the detachable container (shoe) and the drive wheel shaft, which leads to an increased load in the operating mode. The purpose of the work was to upgrade the Conform unit by creating a connection between the shoe and the impeller shaft to obtain a high-quality billet for subsequent wire drawing of the ∅12 mm ingot cast into the electromagnetic crystallizer. An optimal temperature of ingot extrusion (300 °С) was found to eliminate the intense adhesion of wrought metal on the tool surface. The experimental ∅5 mm rod made of 01417 alloy obtained from the ∅12 mm ingot at the Conform unit features high processing ductility. This is indicated by an increase in its yield point and relative elongation. Metallographic studies demonstrated a fine-grained structure achieved in the extruded rod, which provides the conditions for subsequent wire drawing without annealing. The results of the study provide a basis for refining the process conditions of calibrated billet production on the Conform unit followed by wire drawing with required properties.