Dagnier-Antonio Curra-Sosa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Dagnier-Antonio Curra-Sosa has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Roberto Pérez-Rodríguez
Universidad de Holguín
2 shared publications Alejandro Linares-Barranco
University of Seville
1 shared publicationFrancisco Gómez-Rodríguez
University of Seville
1 shared publication- Luis Wilfredo Hernández González
Department of Physics and Engineering, Bindura University of Science Education, Bindura 12100, Zimbabwe
1 shared publication Ricardo Tapiador-Morales
SONY
1 shared publication- Ricardo del Risco-Alfonso
University of Camagüey, Cuba
1 shared publication
Latest Publications
- Open Access
- 13 September 2025
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 9 (9) , 314
Multi-Response Optimization of Milling Parameters of AISI D2 Steel Using Response Surface Methodology and Desirability Function
This study investigates multi-objective optimization of end-milling parameters for AISI D2 cold-worked tool steel using GC1130-coated carbide inserts under wet machining, focusing on cutting speed and feed rate per tooth values beyond manufacturer recommendations. The objective was to identify parameter settings that minimize surface roughness while maximizing cutting tool life—two performance criteria that often conflict in practice. A full-factorial design of experiments was implemented, varying the cutting speed (220–310 m/min) and feed rate (0.06–0.25 mm/tooth). Response Surface Methodology (RSM) was used to develop predictive models, and a desirability function approach (DFA) was applied to perform multi-response optimization under three weighting schemes. The statistical models showed strong reliability, with R2 values of 81.09% for surface roughness and 95.02% for tool life. The optimal settings—220 m/min cutting speed and 0.25 mm/tooth feed—resulted in a tool life of 11.03 min and surface roughness of 0.587 µm. This yielded the highest desirability index (D = 0.8706) under tool-life-prioritized weighting, outperforming other cases by up to 10.69%. These findings offer a practical balance between quality and durability, especially for applications where tool wear is a limiting factor.
- 13 September 2025
- Published by MDPI AG in Journal of Manufacturing and Materials Processing
- Vol. 9 (9) , 314
Open AccessMulti-Response Optimization of Milling Parameters of AISI D2 Steel Using Response Surface Methodology and Desirability Function
This study investigates multi-objective optimization of end-milling parameters for AISI D2 cold-worked tool steel using GC1130-coated carbide inserts under wet machining, focusing on cutting speed and feed rate per tooth values beyond manufacturer recommendations. The objective was to identify parameter settings that minimize surface roughness while maximizing cutting tool life—two performance criteria that often conflict in practice. A full-factorial design of experiments was implemented, varying the cutting speed (220–310 m/min) and feed rate (0.06–0.25 mm/tooth). Response Surface Methodology (RSM) was used to develop predictive models, and a desirability function approach (DFA) was applied to perform multi-response optimization under three weighting schemes. The statistical models showed strong reliability, with R2 values of 81.09% for surface roughness and 95.02% for tool life. The optimal settings—220 m/min cutting speed and 0.25 mm/tooth feed—resulted in a tool life of 11.03 min and surface roughness of 0.587 µm. This yielded the highest desirability index (D = 0.8706) under tool-life-prioritized weighting, outperforming other cases by up to 10.69%. These findings offer a practical balance between quality and durability, especially for applications where tool wear is a limiting factor.
- 12 August 2024
- Published by Springer Nature
- p. 392-402
Spiking Convolution Engine for Spiking Convolution Neural Networks
- 12 August 2024
- Published by Springer Nature
- p. 392-402
Spiking Convolution Engine for Spiking Convolution Neural Networks
- 22 September 2018
- Published by Springer Nature
- p. 51-58
Predictive Model for Specific Energy Consumption in the Turning of AISI 316L Steel
- 22 September 2018
- Published by Springer Nature
- p. 51-58
Predictive Model for Specific Energy Consumption in the Turning of AISI 316L Steel