Victor Birman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Victor Birman has a total of 1 co-authors. Here are the top co-authors by number of shared publications:
Jeffrey Lee
Missouri University of Science and Technology Department of Mechanical and Aerospace Engineering Rolla Missouri 65409
1 shared publication
Latest Publications
- 30 September 2019
- Published by Wiley in ZAMM - Journal of Applied Mathematics and Mechanics / Zeitschrift für Angewandte Mathematik und Mechanik
- Vol. 100 (1)
Wrinkling in sandwich panels with bi‐modular core
The paper is concerned with wrinkling of thin facings in sandwich structures with a bi‐modular elastic core. Bi‐modularity of core implies a different stiffness in tension and compression. The solution to the wrinkling problem is obtained by an extension of the Hoff method. One of two bounding cases are the classical Hoff solution where the stiffness of the core in tension is equal to that in compression. In the second case demonstrated in the paper the mismatch in the stiffness of the core in tension and compression is so large that the higher stiffness can be assumed infinite. The solution for intermediate cases where the ratio of the core stiffness in tension to that in compression is finite is also presented in the paper. In addition, the approach to the analysis of wrinkling utilizing the stresses in the core derived by the theory of elasticity is discussed and the closed‐form solution obtained in the particular case of equal tensile and compressive moduli. It is shown that a mismatch in the elastic moduli of the core in tension and compression results in the change in the mode shape of wrinkling as compared to the core with equal tensile and compressive stiffness. An increase in the stiffness of the facing or using a stiffer bi‐modular core results in a higher wrinkling stress. It is also demonstrated that a higher stiffness of a bi‐modular core in either tension or compression causes only a limited reduction in the energy absorbed prior to wrinkling.
- 30 September 2019
- Published by Wiley in ZAMM - Journal of Applied Mathematics and Mechanics / Zeitschrift für Angewandte Mathematik und Mechanik
- Vol. 100 (1)
Wrinkling in sandwich panels with bi‐modular core
The paper is concerned with wrinkling of thin facings in sandwich structures with a bi‐modular elastic core. Bi‐modularity of core implies a different stiffness in tension and compression. The solution to the wrinkling problem is obtained by an extension of the Hoff method. One of two bounding cases are the classical Hoff solution where the stiffness of the core in tension is equal to that in compression. In the second case demonstrated in the paper the mismatch in the stiffness of the core in tension and compression is so large that the higher stiffness can be assumed infinite. The solution for intermediate cases where the ratio of the core stiffness in tension to that in compression is finite is also presented in the paper. In addition, the approach to the analysis of wrinkling utilizing the stresses in the core derived by the theory of elasticity is discussed and the closed‐form solution obtained in the particular case of equal tensile and compressive moduli. It is shown that a mismatch in the elastic moduli of the core in tension and compression results in the change in the mode shape of wrinkling as compared to the core with equal tensile and compressive stiffness. An increase in the stiffness of the facing or using a stiffer bi‐modular core results in a higher wrinkling stress. It is also demonstrated that a higher stiffness of a bi‐modular core in either tension or compression causes only a limited reduction in the energy absorbed prior to wrinkling.
- 23 September 2018
- Published by Wiley in ZAMM - Journal of Applied Mathematics and Mechanics / Zeitschrift für Angewandte Mathematik und Mechanik
- Vol. 99 (1)
Enhancing toughness of thin films and coatings through embedded nanoinclusions
Buckling of thin films and coatings due to thermal residual stresses has been thoroughly investigated. The subsequent fracture at the film‐to‐substrate interface triggered by buckling may result in a complete delamination of the film, effectively making the structure useless. The approach to the prevention or alleviation of delamination and spalling of the compressed film suggested in the paper is based on embedding random stiff nanoinclusions in the pristine film material. This results in an increase of both the stiffness of the film and the buckling stresses. If the enhanced stiffness is not sufficient to prevent buckling, the strain energy release rate is decreased as a result of embedded nanoinclusions as demonstrated in the paper. This reduction is particularly significant in films whose stiffness is increased by a large factor as compared to that of the pristine material. The effectiveness of the method is particularly evident if the compressive stress exceeds the critical stress of the nanoreinforced film by a relatively small factor. At very high compressive stresses the method of improving toughness considered in the paper is still valid but its relative effectiveness diminishes.
- 23 September 2018
- Published by Wiley in ZAMM - Journal of Applied Mathematics and Mechanics / Zeitschrift für Angewandte Mathematik und Mechanik
- Vol. 99 (1)
Enhancing toughness of thin films and coatings through embedded nanoinclusions
Buckling of thin films and coatings due to thermal residual stresses has been thoroughly investigated. The subsequent fracture at the film‐to‐substrate interface triggered by buckling may result in a complete delamination of the film, effectively making the structure useless. The approach to the prevention or alleviation of delamination and spalling of the compressed film suggested in the paper is based on embedding random stiff nanoinclusions in the pristine film material. This results in an increase of both the stiffness of the film and the buckling stresses. If the enhanced stiffness is not sufficient to prevent buckling, the strain energy release rate is decreased as a result of embedded nanoinclusions as demonstrated in the paper. This reduction is particularly significant in films whose stiffness is increased by a large factor as compared to that of the pristine material. The effectiveness of the method is particularly evident if the compressive stress exceeds the critical stress of the nanoreinforced film by a relatively small factor. At very high compressive stresses the method of improving toughness considered in the paper is still valid but its relative effectiveness diminishes.