Pia Kutschmann

There is currently a lack of suitable methods of non-destructive quality assessment of thermally sprayed coatings. Therefore, this study investigates the suitability of polarization measurements that are adapted to the special needs of thermally sprayed coatings for non-destructive quality testing. For this purpose, a gel electrolyte containing 3.5% NaCl and a measuring cell based on the three-electrode arrangement were developed to prevent the corrosion medium from infiltrating the typical microstructure of thermally sprayed coatings (pores and microcracks). The newly developed method was evaluated on AISI 316L coatings deposited by high velocity air fuel (HVAF) and atmospheric plasma spraying (APS). The polarization curves showed significant differences as a result of spraying process-related changes in the coating microstructure. Even slight differences in oxide content within the AISI 316L coating produced by APS can be detected by the new method. In order to verify the new findings, the coatings were analyzed regarding their microstructure by optical microscope, scanning electron microscope and energy dispersive X-ray spectroscopy. The measuring cell and gel electrolyte developed offer a promising opportunity to evaluate the quality of thermally sprayed coatings in a largely non-destructive manner using polarization curves.

Corrosion testing with gel electrolytes gained attention in the past decade due to the advantage of almost non-destructive and in situ electrochemical measurements of bulk materials. Regarding thermal spray coatings, gel electrolytes offered the opportunity to prevent the infiltration of the typical microstructural features such as pores and microcracks. Using the example of stainless-steel AISI 316L coatings deposited by high velocity air fuel (HVAF) spraying on mild and stainless-steel substrates, the electrochemical corrosion behavior was analyzed in 3.5% NaCl electrolytes in an aqueous and gelled state. In this context, potentiodynamic polarization tests were carried out in a three-electrode corrosion cell, which was adapted for gel electrolyte testing. Gelling was realized with a technical gelatin. The characteristic corrosion values, such as open circuit potential, corrosion potential, and corrosion current density, revealed for the gelled state that the influence of the substrate material used could be eliminated and thus, the coatings itself could be characterized. In contrast, the coating specific microstructure and substrate material significantly affected the potentiodynamic polarization curve in the 3.5% NaCl aqueous electrolyte. Optical microscopy of the coating surfaces and cross-sections proved that the corrosion attack caused by aqueous electrolytes could be mimicked with the gel electrolyte.

Structural features of thermal spray coatings, e.g., porosity, can be beneficial as oil retention volumes in tribological systems in order to improve emergency running properties. While thermal spray coatings can already have a considerable degree of porosity depending on the coating conditions, the finish machining, e.g., by turning, has a significant influence on the final surface properties. Effects like near-surface deformation and subsequent closing of pores during the machining process should be prevented. In the present study, the influence of thermochemical surface hardening on the surface topography of wire arc sprayed 17Cr steel layers after finish turning was investigated. Successful surface hardening by gas nitriding was shown by light microscopic and phase analyses. The surface properties after the various treatment steps were characterized by the surface roughness parameters Ra and Rz, the valley void volume Vvv, and the Abbott curves. A rise of the valley void volume can be beneficial in tribological applications in which a suitable oil retention volume is required. Accordingly, a thermochemical treatment combined with an appropriate subsequent finishing process is suitable to significantly influence the surface properties of thermal spray steel coatings.

Gas nitriding is known as a convenient process to improve the wear resistance of steel components. A precipitation-free hardening by low-temperature processes is established to retain the good corrosion resistance of stainless steel. In cases of thermal spray coatings, the interstitial solvation is achieved without an additional surface activation step. The open porosity permits the penetration of the donator media and leads to a structural diffusion. An inhomogeneous diffusion enrichment occurs at the single spray particle edges within the coating’s microstructure. A decreasing diffusion depth is found with increasing surface distance. The present study investigates an adjusted process management for low-temperature gas nitriding of high velocity oxy-fuel-sprayed AISI 316L coatings. To maintain a homogeneous diffusion depth within the coating, a pressure modulation during the process is studied. Additionally, the use of cracked gas as donator is examined. The process management is designed without an additional surface activation step. Regardless of surface distance, microstructural investigations reveal a homogeneous diffusion depth by a reduced processing time. The constant hardening depth allows a reliable prediction of the coatings’ properties. An enhanced hardness and improved wear resistance is found in comparison with the as-sprayed coating condition.

Austenitic stainless steel exhibits an excellent corrosion behavior. The relatively poor wear resistance can be improved by surface hardening, whereby thermochemical processes offer an economic option. The successful diffusion enrichment of bulk material requires a decomposition of the passive layer. A gas nitriding of high velocity oxygen fuel spraying (HVOF)-sprayed AISI 316L coatings without an additional activation step was studied with a variation of the process temperature depending on the heat-treatment state of the coating. A successful nitrogen enrichment was found in as-sprayed condition, whereas passivation prevents diffusion after solution heat treatment. The phase composition and microstructure formation were examined. The crystal structure and lattice parameters were determined using X-ray diffraction analysis. The identified phases were assigned to the different microstructural elements using the color etchant Beraha II. In as-sprayed condition, the phase formation in the coating is related to the process temperature. The formation of the S-phase with interstitial solvation of nitrogen is achieved by a process temperature of 420 °C. Precipitation occurs during the heat treatment at 520 °C. In both cases, a significant increase in wear resistance was found. The correlation of the thermochemical process parameters and the microstructural properties contributes to a better understanding of the requirements for the process combination of thermal spraying and diffusion.