Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Charul Chadha has a total of 34 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Artificial intelligence and additive manufacturing as a coupled design system: Rethinking inference, manufacturability, and design education

    by Charul Chadha, Garth Crosby, Sabit Ekin, Mohamed Gharib, Eman Hammad, Congrui Jin, Ali Ahmad Malik, Noemi Mendoza Diaz, Calahan Mollan, Gaius C. Nzebuka, et al.

    Artificial intelligence (AI) is becoming deeply integrated into additive manufacturing (AM) workflows, reshaping how designers approach geometry, materials, and process constraints. AI holds significant potential by accelerating design exploration, revealing complex patterns in AM behavior, and supporting earlier assessment of manufacturability. At the same time, it introduces new risks related to model transparency, data quality, physical validity, and the potential for overreliance by students and practitioners. This perspective examines these issues through four guiding questions that address the role of AI in AM-enabled design, the gaps that limit or enable AI contribution, the implications for engineering education, and the responsibilities of the research community in ensuring trustworthy and secure AI–AM integration. The main contributions of this perspective include: (i) Highlighting AI and AM as a coupled inference–fabrication system rather than independent tools; (ii) identifying zones of strong interdependence where inference and manufacturability interact; and (iii) articulating implications for design reasoning, education, and responsible research practice.

  • Open Access

    Effect of laminae count and manufacturing methods on mechanical properties of thin‐ply woven composites

    by Shashank Kushwaha, Mahmoud A. Mahrous, Jacob L. Meyer, Charul Chadha, Iwona M. Jasiuk

    Thin‐ply woven composites exhibit exceptional mechanical performance by delaying the onset of damage, making them suitable for high‐performance structural applications. This study outlines the impact of manufacturing techniques (vacuum bagging and hot pressing), ply count, and fiber waviness on the mechanical properties of aromatic thermosetting copolyester/carbon‐fiber (ATSP/CF) composites. The analysis encompasses several different ply counts, evaluating their effects on the in‐plane elastic modulus (0°–90°) and tensile strength. Results demonstrate that reducing the waviness (or crimp) ratio significantly enhances the in‐plane elastic modulus, with improvements up to 188%, highlighting the importance of fiber alignment. Vacuum bagging produced ply thicknesses from 128 to 58 μm for 1–36 plies, with in‐plane elastic moduli from 30.3 to 87.2 GPa, and 4‐ and 8‐ply samples showed approximately 40% higher stiffness than those made by hot pressing. ATSP resin with high thermal stability (up to 400°C) and recyclability was used. Furthermore, this study highlights the microstructural enhancements achieved through vacuum bagging, as revealed by scanning electron and optical microscopy, and micro‐computed tomography imaging. This paper provides insights into damage mitigation and achieving enhanced mechanical properties by controlling fiber waviness using vacuum bagging and higher ply count in thin‐ply ATSP/CF composites.Highlights: Crimp ratio reduction enhances elastic in‐plane elastic modulus up to 188%. Vacuum bagging increases modulus over the hot pressing manufacturing method by 40%. Lowering thickness‐per‐ply increases failure strain from 0.8% to 1.2%. Explored the performance of a novel ATSP matrix with high recyclability and thermal stability.

  • Open Access

    Exploring the Effect of Specimen Size on Elastic Properties of Fused-Filament-Fabrication-Printed Polycarbonate and Thermoplastic Polyurethane

    by Charul Chadha, Gabriel Olaivar, Mahmoud A. Mahrous, Albert E. Patterson, Iwona Jasiuk

    Additive manufacturing (AM) is often used to create designs inspired by topology optimization and biological structures, yielding unique cross-sectional geometries spanning across scales. However, manufacturing defects intrinsic to AM can affect material properties, limiting the applicability of a uniform material model across diverse cross-sections. To examine this phenomenon, this paper explores the influence of specimen size and layer height on the compressive modulus of polycarbonate (PC) and thermoplastic polyurethane (TPU) specimens fabricated using fused filament fabrication (FFF). Micro-computed tomography imaging and compression testing were conducted on the printed samples. The results indicate that while variations in the modulus were statistically significant due to both layer height and size of the specimen in TPU, variations in PC were only statistically significant due to layer height. The highest elastic modulus was observed at a 0.2 mm layer height for both materials across different sizes. These findings offer valuable insights into design components for FFF, emphasizing the importance of considering mechanical property variations due to feature size, especially in TPU. Furthermore, locations with a higher probability of failure are recommended to be printed closer to the print bed, especially for TPU, because of the lower void volume fraction observed near the heated print bed.


  • Open Access

    Size Effects in Polycarbonate and TPU 3D-Printed via Fused Filament Fabrication

    by Charul Chadha, Gabriel Olaivar, Mahmoud A. Mahrous, Iwona Jasiuk, Albert E. Patterson

    This paper investigates the influence of sample size and layer height on the elastic modulus of samples 3D printed by fused filament fabrication (FFF). Cubic samples of different sizes from either a stiff thermoplastic polymer (polycarbonate (PC)) or a soft polymer (thermoplastic polyurethane (TPU)) were printed at three different layer heights: 0.1 mm, 0.2 mm, and 0.4 mm. The samples were imaged using micro-computed tomography to visualize porosity and tested under compression. The results indicate that the elastic modulus of TPU varied with sample size, demonstrating size effects due to high porosity. In contrast, PC samples had a low void volume fraction and did not demonstrate statistically significant size effects on the elastic modulus. The variations in elastic modulus due to layer height were statistically significant for both materials. The highest elastic modulus was observed at 0.2 mm layer height for both materials across different sample sizes, which can be attributed to low void volume fractions. The study develops process-structure-property relations for PC and TPU samples manufactured by FFF. It provides new insights into the design guidelines for FFF based on the size effects. The results indicate that variations in mechanical properties due to size effects must be considered during the design stage for TPU to accurately predict the material’s behavior. Additionally, the locations of the printed parts that are subjected to higher loads should be printed closer to the heated print bed due to the lower void volume fraction observed in the section of the samples printed adjacent to the heated print bed.


  • Open Access

    Improving the Accuracy of the Deep Energy Method

    by Charul Chadha, Junyan He, Diab Abueidda, Seid Koric, Erman Guleryuz, Iwona Jasiuk

    The deep energy method (DEM), a type of physics-informed neural network, is evolving as an alternative to finite element analysis. This method employs the principle of minimum potential energy to predict deformations under static loading conditions. However, the model’s accuracy is contingent upon choosing the appropriate architecture for the model, which can be challenging due to the high interactions between hyperparameters, large search space, difficulty in identifying objective functions, and non-convex relationships with the objective functions. To improve DEM’s accuracy, we first introduce random Fourier feature (RFF) mapping. RFF mapping helps with the training of the model by reducing bias towards high frequencies. The effects of six hyperparameters are then studied under compression, tension, and bending loads in planar linear elasticity. Based on this study, a systematic automated hyperparameter optimization approach is proposed. Due to the high interaction between hyperparameters and the non-convex nature of the optimization problem, Bayesian optimization algorithms are used. The models trained using optimized hyperparameters and having Fourier feature mapping can accurately predict deflections compared to finite element analysis. Additionally, the deflections obtained for tension and compression load cases are more sensitive to variations in hyperparameters than bending.

  • Open Access

    Tensile behavior of individual fibers and films made via material extrusion additive manufacturing

    by Albert E. Patterson, Charul Chadha, Iwona M. Jasiuk, James T. Allison


  • Open Access

    Extending the Operating Life of Thermoplastic Components via On-Demand Patching and Repair Using Fused Filament Fabrication

    by Charul Chadha, Kai James, Iwona M. Jasiuk, Albert E. Patterson

    Polymer-based engineering materials (plastics, polymer matrix composites, and similar) are becoming more widely used for the design and construction of consumer products and systems. While providing a host of design benefits, these materials also can have a large detrimental effect on the environment when not handled properly. One of the best ways to increase the sustainability of systems created using these materials is to extend their operating life as much as possible. Additive manufacturing (AM) technologies offer a powerful tool for this, as they allow easy repair of damaged or worn components in an automated or semi-automated way. This article explores the use of the fused filament fabrication (FFF) process as a tool for repairing high-value (i.e., difficult or expensive to replace) thermoplastic parts. The major design opportunities and restrictions are presented, as well as an evaluation of the types of repair jobs for which this process could be suitable and effective. Advice and ideas for future implementations and improvements are provided as well. A detailed case study is presented, where cracked ABS bars were repaired using FFF-deposited patches while varying the print parameters using a factorial designed experiment. The repaired bars were tested against the baseline and in most cases were found to be as good as or better than the original bars under a bending load. This case study demonstrates the concepts and explores how this repair approach could be realistically employed in practice.


  • Open Access

    Identification and Mapping of Manufacturability Constraints for Extrusion-Based Additive Manufacturing

    by Albert E. Patterson, Charul Chadha, Iwona M. Jasiuk

    This article develops and demonstrates a set of design-focused manufacturability constraints for the fused deposition modeling/fused filament fabrication (FDM/FFF) process. These can be mapped from the basic behavior and process characteristics and formulated in terms of implicit or explicit design constraints. When the FDM/FFF process is explored and examined for its natural limitations and behavior, it can provide a set of manufacturing considerations (advantages, limitations, and best practices). These can be converted into manufacturing constraints, which are practical limits on the ability of the process. Finally, these can be formulated in terms of design–useful manufacturability constraints. Many of the constants and parameters must be determined experimentally for specific materials. The final list of 54 major manufacturability constraints presented in this work will better inform designers considering using FDM/FFF as a manufacturing process, and help guide design decisions. After derivation and presentation of the constraint set, extensive discussion about practical implementation is provided at the end of the paper, including advice about experimentally determining constants and appropriate printing parameters. Finally, three case studies are presented which implement the constraints for simple design problems.