Yajiao Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yajiao Li has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Jiake Li
State Key Laboratory of Water Engineering Ecology and Environment in Arid Area, Xi’an University of Technology, Xi’an, China
4 shared publications Bei-Bei Chai
2 shared publications- Wei Li
College of Civil Engineering and Architecture, Wenzhou University, Wenzhou, China
2 shared publications Xiao-Guang Zhao
2 shared publications- Bei Zhang
State Key Laboratory of Eco-hydraulics in Northwest Arid Region of China, Xi’an University of Technology, Xi’an 710048, China
1 shared publication - Beibei Chai
Collaborative innovation center for intelligent regulation and comprehensive management of water resources, School of Water Conservancy and Hydroelectric, Hebei University of Engineering, Handan 056038, China
1 shared publication
Latest Publications
- Open Access
Reduction and Accumulative Characteristics of Dissolved Heavy Metals in Modified Bioretention Media
Twelve bioretention filter columns with different media were designed to study the effects of media on dissolved heavy metals in bioretention systems by changing three test conditions (inflow concentration, discharge ratio, and recurrence interval). The results showed that the average load reduction efficiency of the bioretention soil media (BSM)+10%water treatment residue, BSM+10%green zeolite, and BSM+10%medicinal stone for Cu and Zn was larger than 80%. The highest volume reduction efficiency is 39.25% by BSM+coconut bran. Among the three factors selected in tests, inflow concentration had the biggest degree of influence, followed by discharge ratio and recurrence interval. The media of the upper, middle, and lower layers of each filter column were detected before and after the treatment to study the accumulative characteristics of heavy metals in the bioretention system. The accumulation of Cu, Zn, and Cd in the media of BSM+medicinal stone, BSM+fly ash, BSM+vermiculite, and BSM+turfy soil was relatively low. The contents of the three metals were positively correlated with urease and negatively correlated with protease in the media, but no obvious rule was showed in the accumulation of dissolved heavy metals with depth.
Open AccessReduction and Accumulative Characteristics of Dissolved Heavy Metals in Modified Bioretention Media
Twelve bioretention filter columns with different media were designed to study the effects of media on dissolved heavy metals in bioretention systems by changing three test conditions (inflow concentration, discharge ratio, and recurrence interval). The results showed that the average load reduction efficiency of the bioretention soil media (BSM)+10%water treatment residue, BSM+10%green zeolite, and BSM+10%medicinal stone for Cu and Zn was larger than 80%. The highest volume reduction efficiency is 39.25% by BSM+coconut bran. Among the three factors selected in tests, inflow concentration had the biggest degree of influence, followed by discharge ratio and recurrence interval. The media of the upper, middle, and lower layers of each filter column were detected before and after the treatment to study the accumulative characteristics of heavy metals in the bioretention system. The accumulation of Cu, Zn, and Cd in the media of BSM+medicinal stone, BSM+fly ash, BSM+vermiculite, and BSM+turfy soil was relatively low. The contents of the three metals were positively correlated with urease and negatively correlated with protease in the media, but no obvious rule was showed in the accumulation of dissolved heavy metals with depth.
- Open Access
Simulation of Rain Garden Effects in Urbanized Area Based on Mike Flood
An urban storm and surface water pollution model (MIKE FLOOD) was used to assess the impact of rain gardens on water quantity and quality for an urban area in Xi’an. After the rain garden measures were added, the results show that: (1) In the case where the total proportion of rain gardens was 2%, the overflow reduction rate was 6.74% to 65.23%, the number of overflow points reduction rate was 1.79% to 65.63%, the overload pipes reduction rate was 0% to 11.15%, the runoff reduction rate was 1.93% to 9.69%; (2) Under different rainfall conditions, the load reduction rate of suspended solids (SS), chemical oxygen demand (COD), total nitrogen (TN), and total phosphorus (TP) were 2.36% to 30.35%, 2.37% to 30.11%, 2.34% to 30.08%, and 2.32% to 31.35%, respectively; (3) The submersion ranges of different submerged depths and submerged durations were reduced by 0.30% to 64.18% and 7.12% to 100%, respectively. The statistics of the automatic modeling and intelligent analysis system (AMIAS) showed that the rain garden regulation range of the waterlogging risk area was 0.78% to 100%. The rain garden has a good control effect on urban storm runoff in terms of water volume and water quality, but as the rainfall recurrence interval increases, the control effect will decrease.
Open AccessSimulation of Rain Garden Effects in Urbanized Area Based on Mike Flood
An urban storm and surface water pollution model (MIKE FLOOD) was used to assess the impact of rain gardens on water quantity and quality for an urban area in Xi’an. After the rain garden measures were added, the results show that: (1) In the case where the total proportion of rain gardens was 2%, the overflow reduction rate was 6.74% to 65.23%, the number of overflow points reduction rate was 1.79% to 65.63%, the overload pipes reduction rate was 0% to 11.15%, the runoff reduction rate was 1.93% to 9.69%; (2) Under different rainfall conditions, the load reduction rate of suspended solids (SS), chemical oxygen demand (COD), total nitrogen (TN), and total phosphorus (TP) were 2.36% to 30.35%, 2.37% to 30.11%, 2.34% to 30.08%, and 2.32% to 31.35%, respectively; (3) The submersion ranges of different submerged depths and submerged durations were reduced by 0.30% to 64.18% and 7.12% to 100%, respectively. The statistics of the automatic modeling and intelligent analysis system (AMIAS) showed that the rain garden regulation range of the waterlogging risk area was 0.78% to 100%. The rain garden has a good control effect on urban storm runoff in terms of water volume and water quality, but as the rainfall recurrence interval increases, the control effect will decrease.
- Open Access
Adsorption Characteristics of Several Bioretention-Modified Fillers for Phosphorus
To optimize the bioretention mixed fillers with better removal of phosphorus, this paper studies the adsorption characteristics of single filler and modified mixed filler through static adsorption experiments, and adopts the dynamical mini-column experiments to examine the adsorption capacities of the soil and modified mixed fillers. Results show that, in the static adsorption experiments, both water treatment residual (WTR) and fly ash exhibit good adsorption capacity when used as a single filler and modifier. Adsorption capacity increases with increasing WTR and fly ash dosage in the mixed filler. The modified mixed filler with WTR exerts a clear effect in the dynamic adsorption experiment, which is unsaturated when influent phosphorus concentration is 1 mg/L and inflow amount is equivalent to 15 years of precipitation. The adsorption capacity of WTR is 3.5–4.5 times that of other mixed fillers. Fly ash as a modifier shows a poor dynamic adsorption effect and thus must be continuously studied. In this study, WTR is recommended as a bioretention phosphorus removal additive. In engineering applications, the amount of WTR added can be controlled within 5–10% (by mass) according to influent phosphorus concentration.
Open AccessAdsorption Characteristics of Several Bioretention-Modified Fillers for Phosphorus
To optimize the bioretention mixed fillers with better removal of phosphorus, this paper studies the adsorption characteristics of single filler and modified mixed filler through static adsorption experiments, and adopts the dynamical mini-column experiments to examine the adsorption capacities of the soil and modified mixed fillers. Results show that, in the static adsorption experiments, both water treatment residual (WTR) and fly ash exhibit good adsorption capacity when used as a single filler and modifier. Adsorption capacity increases with increasing WTR and fly ash dosage in the mixed filler. The modified mixed filler with WTR exerts a clear effect in the dynamic adsorption experiment, which is unsaturated when influent phosphorus concentration is 1 mg/L and inflow amount is equivalent to 15 years of precipitation. The adsorption capacity of WTR is 3.5–4.5 times that of other mixed fillers. Fly ash as a modifier shows a poor dynamic adsorption effect and thus must be continuously studied. In this study, WTR is recommended as a bioretention phosphorus removal additive. In engineering applications, the amount of WTR added can be controlled within 5–10% (by mass) according to influent phosphorus concentration.
- 24 November 2016
- Published by HARD Publishing Company in Polish Journal of Environmental Studies
- Vol. 25 (6) , 2293-2304
Effects of Hydrostatic Pressure on the Nitrogen Cycle of Sediment
We carried out a simulation experiment in a laboratory in order to study the effects of hydrostatic pressure from 0.1 MPa to 1.0 MPa on nitrogen cycles at the water-sediment interface of a freshwater reservoir. The results show that high hydrostatic pressure facilitates the release of nitrogen at the interface and ammonification, but has little influence on denitrification. And high hydrostatic pressure will also significantly increase the activity of dehydrogenases and proteases in the sediment, and has little influence on ureases and nitrate reductase activity. The pressure caused a large accumulation of such pollutants as ammoniacal nitrogen and nitrate nitrogen at the interface, seriously worsening the overlying water quality. As PLFA and PCR-DGGE analysis results show, different hydrostatic pressures will lead to remarkable differences in the microbial community’s structure and heredity. Within the range 0.1 MPa to 1.0 MPa, the microbial community structure is more diverse under high hydrostatic pressure than under normal pressure.
- 24 November 2016
- Published by HARD Publishing Company in Polish Journal of Environmental Studies
- Vol. 25 (6) , 2293-2304
Effects of Hydrostatic Pressure on the Nitrogen Cycle of Sediment
We carried out a simulation experiment in a laboratory in order to study the effects of hydrostatic pressure from 0.1 MPa to 1.0 MPa on nitrogen cycles at the water-sediment interface of a freshwater reservoir. The results show that high hydrostatic pressure facilitates the release of nitrogen at the interface and ammonification, but has little influence on denitrification. And high hydrostatic pressure will also significantly increase the activity of dehydrogenases and proteases in the sediment, and has little influence on ureases and nitrate reductase activity. The pressure caused a large accumulation of such pollutants as ammoniacal nitrogen and nitrate nitrogen at the interface, seriously worsening the overlying water quality. As PLFA and PCR-DGGE analysis results show, different hydrostatic pressures will lead to remarkable differences in the microbial community’s structure and heredity. Within the range 0.1 MPa to 1.0 MPa, the microbial community structure is more diverse under high hydrostatic pressure than under normal pressure.
- Open Access
- 19 February 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (52) , 24894-24912
Bioswale column experiments and simulation of pollutant removal from urban road stormwater runoff
The concomitant flux of pollutants carried by urban storm water runoff to the surface of water bodies causes a series of environmental issues. Bioswale, which is an effective purification measure of urban surface runoff pollutants, was investigated to determine the relationship between bioswale composition and purification. Results indicate that the pollutant removal rate of bioswales decreases with an increase in influent concentration. Various selected vegetation combinations showed no significant difference in terms of pollutant removal in two months after being planted within a single rainfall. Increasing the thickness of the planting soil and artificial filler layers can improve the contaminant removal rate. Various artificial filler compositions were proven to have different effects on pollutant purification. Planting soil and a mixture of coal ash and sand were the best choice, whereas sand was the worst. The total nitrogen (TN) removal rate increased with submerged zone height, whereas the removal of chemical oxygen demand (COD) and total phosphorus (TP) showed no significant change. The addition of an external carbon source increased TN concentration removal and decreased COD concentration removal without significantly affecting TP. The curve analysis of the pollutant removal rate and various factors was established by processing the statistical results through the SPSS software. The equation of linear regression, which reveals the relationship between the control effect and its influencing factors, was obtained based on the partial least squares model.
- 19 February 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (52) , 24894-24912
Open AccessBioswale column experiments and simulation of pollutant removal from urban road stormwater runoff
The concomitant flux of pollutants carried by urban storm water runoff to the surface of water bodies causes a series of environmental issues. Bioswale, which is an effective purification measure of urban surface runoff pollutants, was investigated to determine the relationship between bioswale composition and purification. Results indicate that the pollutant removal rate of bioswales decreases with an increase in influent concentration. Various selected vegetation combinations showed no significant difference in terms of pollutant removal in two months after being planted within a single rainfall. Increasing the thickness of the planting soil and artificial filler layers can improve the contaminant removal rate. Various artificial filler compositions were proven to have different effects on pollutant purification. Planting soil and a mixture of coal ash and sand were the best choice, whereas sand was the worst. The total nitrogen (TN) removal rate increased with submerged zone height, whereas the removal of chemical oxygen demand (COD) and total phosphorus (TP) showed no significant change. The addition of an external carbon source increased TN concentration removal and decreased COD concentration removal without significantly affecting TP. The curve analysis of the pollutant removal rate and various factors was established by processing the statistical results through the SPSS software. The equation of linear regression, which reveals the relationship between the control effect and its influencing factors, was obtained based on the partial least squares model.
- 1 July 2015
- p. 845-55
Phospholipids fatty acids of drinking water reservoir sedimentary microbial community: Structure and function responses to hydrostatic pressure and other physico-chemical properties.
Microbial communities in three drinking water reservoirs, with different depth in Xi'an city, were quantified by phospholipids fatty acids analysis and multivariate statistical analysis was employed to interpret their response to different hydrostatic pressure and other physico-chemical properties of sediment and overlying water. Principle component analyses of sediment characteristics parameters showed that hydrostatic pressure was the most important effect factor to differentiate the overlying water quality from three drinking water reservoirs from each other. NH4+ content in overlying water was positive by related to hydrostatic pressure, while DO in water-sediment interface and sediment OC in sediment were negative by related with it. Three drinking water reservoir sediments were characterized by microbial communities dominated by common and facultative anaerobic Gram-positive bacteria, as well as, by sulfur oxidizing bacteria. Hydrostatic pressure and physico-chemical properties of sediments (such as sediment OC, sediment TN and sediment TP) were important effect factors to microbial community structure, especially hydrostatic pressure. It is also suggested that high hydrostatic pressure and low dissolved oxygen concentration stimulated Gram-positive and sulfate-reducing bacteria (SRB) bacterial population in drinking water reservoir sediment. This research supplied a successful application of phospholipids fatty acids and multivariate analysis to investigate microbial community composition response to different environmental factors. Thus, few physico-chemical factors can be used to estimate composition microbial of community as reflected by phospholipids fatty acids, which is difficult to detect.
- 1 July 2015
- p. 845-55
Phospholipids fatty acids of drinking water reservoir sedimentary microbial community: Structure and function responses to hydrostatic pressure and other physico-chemical properties.
Microbial communities in three drinking water reservoirs, with different depth in Xi'an city, were quantified by phospholipids fatty acids analysis and multivariate statistical analysis was employed to interpret their response to different hydrostatic pressure and other physico-chemical properties of sediment and overlying water. Principle component analyses of sediment characteristics parameters showed that hydrostatic pressure was the most important effect factor to differentiate the overlying water quality from three drinking water reservoirs from each other. NH4+ content in overlying water was positive by related to hydrostatic pressure, while DO in water-sediment interface and sediment OC in sediment were negative by related with it. Three drinking water reservoir sediments were characterized by microbial communities dominated by common and facultative anaerobic Gram-positive bacteria, as well as, by sulfur oxidizing bacteria. Hydrostatic pressure and physico-chemical properties of sediments (such as sediment OC, sediment TN and sediment TP) were important effect factors to microbial community structure, especially hydrostatic pressure. It is also suggested that high hydrostatic pressure and low dissolved oxygen concentration stimulated Gram-positive and sulfate-reducing bacteria (SRB) bacterial population in drinking water reservoir sediment. This research supplied a successful application of phospholipids fatty acids and multivariate analysis to investigate microbial community composition response to different environmental factors. Thus, few physico-chemical factors can be used to estimate composition microbial of community as reflected by phospholipids fatty acids, which is difficult to detect.