Renata Latypova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Renata Latypova has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
Jukka Kömi
8 shared publications- Sakari Pallaspuro
University of Oulu
7 shared publications Timo Kauppi
5 shared publicationsHannu Hänninen
4 shared publicationsSaara Mehtonen
4 shared publicationsOskari Seppälä
Oulun Yliopisto Oulu Finland
3 shared publications
Latest Publications
- Open Access
- 18 August 2026
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 345
Hydrogen embrittlement resistance of low-temperature tempered direct-quenched martensitic steel
- 18 August 2026
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 345
Open AccessHydrogen embrittlement resistance of low-temperature tempered direct-quenched martensitic steel
- Open Access
- 1 December 2025
- Published by Elsevier in Next Materials
- Vol. 10
Hydrogen diffusion in 0.2–0.4wt% carbon martensitic and martensitic-austenitic advanced high-strength steels
- 1 December 2025
- Published by Elsevier in Next Materials
- Vol. 10
Open AccessHydrogen diffusion in 0.2–0.4wt% carbon martensitic and martensitic-austenitic advanced high-strength steels
- Open Access
- 4 July 2025
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 326
Effect of rapid tempering and cementite morphology on hydrogen diffusion and trapping in a medium-carbon advanced high-strength steel
- 4 July 2025
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 326
Open AccessEffect of rapid tempering and cementite morphology on hydrogen diffusion and trapping in a medium-carbon advanced high-strength steel
- Open Access
- 14 July 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 908
Mitigating hydrogen embrittlement via film-like retained austenite in 2 GPa direct-quenched and partitioned martensitic steels
- 14 July 2024
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 908
Open AccessMitigating hydrogen embrittlement via film-like retained austenite in 2 GPa direct-quenched and partitioned martensitic steels
- Open Access
- 15 June 2023
- Published by Wiley in Materials and Corrosion
- Vol. 74 (10) , 1514-1520
Data‐analysis method for hydrogen embrittlement tuning‐fork test
A new data‐analysis method is proposed for processing time‐force data obtained from a recently developed novel tuning‐fork test that has been utilized in hydrogen embrittlement studies. The analysis method is based on the application of suitable functions that are shown to provide a good fit to the data. The fitted functions allow for the calculation of first‐ and second‐order time derivatives from the initially scattered data. The negative peaks of the second‐order derivatives of the fitted functions can be associated with the more sudden changes that could be observed in the experimental data. Since these sudden changes are expected to be related to the operation of the mechanisms at the microstructural level, the present analysis provides a potentially useful method for obtaining knowledge of the operation of these mechanisms.
- 15 June 2023
- Published by Wiley in Materials and Corrosion
- Vol. 74 (10) , 1514-1520
Open AccessData‐analysis method for hydrogen embrittlement tuning‐fork test
A new data‐analysis method is proposed for processing time‐force data obtained from a recently developed novel tuning‐fork test that has been utilized in hydrogen embrittlement studies. The analysis method is based on the application of suitable functions that are shown to provide a good fit to the data. The fitted functions allow for the calculation of first‐ and second‐order time derivatives from the initially scattered data. The negative peaks of the second‐order derivatives of the fitted functions can be associated with the more sudden changes that could be observed in the experimental data. Since these sudden changes are expected to be related to the operation of the mechanisms at the microstructural level, the present analysis provides a potentially useful method for obtaining knowledge of the operation of these mechanisms.
- Open Access
- 7 June 2023
- Published by Elsevier in Materials & Design
- Vol. 231
Rapid tempering of a medium-carbon martensitic steel: In-depth exploration of the microstructure – mechanical property evolution
- 7 June 2023
- Published by Elsevier in Materials & Design
- Vol. 231
Open AccessRapid tempering of a medium-carbon martensitic steel: In-depth exploration of the microstructure – mechanical property evolution
- Open Access
- 15 May 2023
- Published by Walter de Gruyter GmbH in Corrosion Reviews
- Vol. 41 (5) , 537-544
The effect of Pd and Ni coatings on hydrogen permeation experiments of as-quenched martensitic steel
Hydrogen permeation technique is a widely used testing method for the determination of hydrogen diffusion coefficient (D), which is an important parameter considering hydrogen embrittlement. A palladium (Pd) or nickel (Ni) coating is often utilised on the hydrogen detection side of the test specimens. Here, we investigate the effect of Pd and Ni coatings on hydrogen diffusion in a martensitic 500 HBW hardness low-alloy steel in the thickness range of 0.5 – 0.8 mm using a refined successive transient method and compare against an uncoated reference specimen. Both coatings yield similar average D values (6 – 6.6 × 10−7 cm2/s), but the best repeatability is achieved with Pd coating. With Ni coating, D values decrease with the increasing specimen thickness, which is partly caused by a slower hydrogen diffusion in Ni, and therefore a concentration gradient at the specimen-coating interface. The uncoated specimen has a poor transient fit, and significantly lower D (2.1 × 10−7 cm2/s) due to surface oxidation. With both coatings, the steepness of the last decay transient was highly affected by specimen thickness, and therefore the density of reversible hydrogen traps is only comparable for similar thicknesses.
- 15 May 2023
- Published by Walter de Gruyter GmbH in Corrosion Reviews
- Vol. 41 (5) , 537-544
Open AccessThe effect of Pd and Ni coatings on hydrogen permeation experiments of as-quenched martensitic steel
Hydrogen permeation technique is a widely used testing method for the determination of hydrogen diffusion coefficient (D), which is an important parameter considering hydrogen embrittlement. A palladium (Pd) or nickel (Ni) coating is often utilised on the hydrogen detection side of the test specimens. Here, we investigate the effect of Pd and Ni coatings on hydrogen diffusion in a martensitic 500 HBW hardness low-alloy steel in the thickness range of 0.5 – 0.8 mm using a refined successive transient method and compare against an uncoated reference specimen. Both coatings yield similar average D values (6 – 6.6 × 10−7 cm2/s), but the best repeatability is achieved with Pd coating. With Ni coating, D values decrease with the increasing specimen thickness, which is partly caused by a slower hydrogen diffusion in Ni, and therefore a concentration gradient at the specimen-coating interface. The uncoated specimen has a poor transient fit, and significantly lower D (2.1 × 10−7 cm2/s) due to surface oxidation. With both coatings, the steepness of the last decay transient was highly affected by specimen thickness, and therefore the density of reversible hydrogen traps is only comparable for similar thicknesses.
- Open Access
- 30 January 2023
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 281
Influence of prior austenite grain structure on hydrogen-induced fracture in as-quenched martensitic steels
- 30 January 2023
- Published by Elsevier in Engineering Fracture Mechanics
- Vol. 281
Open AccessInfluence of prior austenite grain structure on hydrogen-induced fracture in as-quenched martensitic steels
- 20 July 2020
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 76 (10) , 954-966
Hydrogen-Induced Cracking of 500 HBW Steels Studied Using a Novel Tuning-Fork Test with Integrated Loadcell System
Hydrogen embrittlement is a well-known problem with high-strength steels. An important aspect of hydrogen embrittlement research is the effect of the prior austenite grain (PAG) structure on hydrogen-induced fracture. The microstructural anisotropy of PAG structure depends on the steel manufacturing process. In this study, 500 HBW martensitic steels with different PAG structures are investigated with a novel tuning-fork test that utilizes an integrated loadcell system. The loadcell clamping system is used during hydrogen charging, allowing tracking of the applied force throughout the tests, which enables detection of separate phases of cracking and time-to-fracture. The elongated PAG morphology produces different results depending on the crack path direction in relation to the rolling direction, whereas the equiaxed PAG morphology does not manifest an orientation dependence. Depending on the PAG shape, also the fracture morphology differs. Time-to-fracture results show that elongated grain morphologies with transgranular quasi-cleavage crack propagation are more beneficial against hydrogen-induced fracture than equiaxed grain structure with intergranular crack propagation. These results demonstrate that the shape of the PAG structure plays an important role in the crack propagation mechanism and that it is important to consider the possible direction of hydrogen-induced cracks in the final structural applications.
- 20 July 2020
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 76 (10) , 954-966
Hydrogen-Induced Cracking of 500 HBW Steels Studied Using a Novel Tuning-Fork Test with Integrated Loadcell System
Hydrogen embrittlement is a well-known problem with high-strength steels. An important aspect of hydrogen embrittlement research is the effect of the prior austenite grain (PAG) structure on hydrogen-induced fracture. The microstructural anisotropy of PAG structure depends on the steel manufacturing process. In this study, 500 HBW martensitic steels with different PAG structures are investigated with a novel tuning-fork test that utilizes an integrated loadcell system. The loadcell clamping system is used during hydrogen charging, allowing tracking of the applied force throughout the tests, which enables detection of separate phases of cracking and time-to-fracture. The elongated PAG morphology produces different results depending on the crack path direction in relation to the rolling direction, whereas the equiaxed PAG morphology does not manifest an orientation dependence. Depending on the PAG shape, also the fracture morphology differs. Time-to-fracture results show that elongated grain morphologies with transgranular quasi-cleavage crack propagation are more beneficial against hydrogen-induced fracture than equiaxed grain structure with intergranular crack propagation. These results demonstrate that the shape of the PAG structure plays an important role in the crack propagation mechanism and that it is important to consider the possible direction of hydrogen-induced cracks in the final structural applications.