Debal Pramanik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Debal Pramanik has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
S. Mitra
Jadavpur University, India
6 shared publicationsS. Sarkar
Jadavpur University, India
6 shared publications- Abhishek Sen
Calcutta Institute of Technology
5 shared publications - Nilanjan Roy
Jadavpur University
5 shared publications A.S Kuar
Jadavpur University
4 shared publications- Arunanshu Shekhar Kuar
Department of Production Engineering, Jadavpur University, Kolkata 700032, India
4 shared publications
Latest Publications
- 6 August 2025
- Published by Springer Nature in Welding in the World
- Vol. 70 (7) , 2697-2716
Advanced fiber laser welding for high-temperature applications: dissimilar welds of austenitic stainless steel (316L) and Hastelloy C-276
- 6 August 2025
- Published by Springer Nature in Welding in the World
- Vol. 70 (7) , 2697-2716
Advanced fiber laser welding for high-temperature applications: dissimilar welds of austenitic stainless steel (316L) and Hastelloy C-276
- Open Access
- 15 July 2025
- Published by International Academic Publishing House
- Vol. 1 (3) , 55-66
Optimisation of Metal Active Gas Welding on Mild Steel Using Response Surface Methodology
The widespread use of metal manufacturing in the modern world is aided by Metal Active Gas (MAG) welding, which is considered both efficient and versatile and can be included in the automation process. The current study is an optimization exercise dealing with MAG welding of mild steel to determine the influence of four prominent process parameters, namely, welding speed, welding current, welding voltage, and wire feed rate, upon two key process responses, namely, joint penetration and percentage defect. The empirical model was obtained using a Central Composite Design (CCD) method of the Response Surface Methodology (RSM) in order to establish the best settings of various parameters. The ANOVA and the results of the regression analysis showed that the current and the wire feed rate are the key factors that have a substantial impact on joint penetration, whereas the percentage of defects is heavily dependent on the voltage and the feed rate. High current and low wire feed rate yielded maximum joint penetration, and low weld defects were found at mid-range current, the voltage application, and weld speed. The statistical accuracy of the models developed was high, with R2 values of 97.44% for joint penetration and 96.32% for defects. The results included great information that may be used in enhancing the quality of welds, process stability, and efficiency, and it has considerable implications for industries that depend on well-performing welded structures.
- 15 July 2025
- Published by International Academic Publishing House
- Vol. 1 (3) , 55-66
Open AccessOptimisation of Metal Active Gas Welding on Mild Steel Using Response Surface Methodology
The widespread use of metal manufacturing in the modern world is aided by Metal Active Gas (MAG) welding, which is considered both efficient and versatile and can be included in the automation process. The current study is an optimization exercise dealing with MAG welding of mild steel to determine the influence of four prominent process parameters, namely, welding speed, welding current, welding voltage, and wire feed rate, upon two key process responses, namely, joint penetration and percentage defect. The empirical model was obtained using a Central Composite Design (CCD) method of the Response Surface Methodology (RSM) in order to establish the best settings of various parameters. The ANOVA and the results of the regression analysis showed that the current and the wire feed rate are the key factors that have a substantial impact on joint penetration, whereas the percentage of defects is heavily dependent on the voltage and the feed rate. High current and low wire feed rate yielded maximum joint penetration, and low weld defects were found at mid-range current, the voltage application, and weld speed. The statistical accuracy of the models developed was high, with R2 values of 97.44% for joint penetration and 96.32% for defects. The results included great information that may be used in enhancing the quality of welds, process stability, and efficiency, and it has considerable implications for industries that depend on well-performing welded structures.
- Open Access
- 15 July 2025
- Published by International Academic Publishing House
- Vol. 1 (3) , 34-43
Experimental Evaluation of Key Welding Process Parameters on the Performance of MIG Welded Mild Steel
The implementation of innovative techniques and sophisticated procedures in welding enhances efficiency and productivity. Automation, particularly robot assisted automation, is crucial in the development of advanced welding systems. In contrast to traditional Gas Metal Arc Welding (GMAW), contemporary methods enable reduced thermal input, maintaining the workpiece and weld areas at relatively lower temperatures. This reduced heat input not only minimizes thermal distortion but also improves weld precision, reduces spatter, and enables the successful joining of mild steel, galvanized sheets, and dissimilar metals, such as steel and aluminium. In this regard, this current research paper proposes to unearth the effect of the three parameters that are attributed to considerable input of metal and influence on the mechanical performance of Metal Inert Gas (MIG) welded mild steel joints, such as current, voltage, and wire feed speed. Weld strength was assessed by mechanical properties such as tensile strength, hardness, and microstructural characteristics. The techniques employed in underpinning the experiments were drawn using a Taguchi L9 orthogonal array and three uses of three-level input parameters. ANOVA results demonstrated that the strongest influence was made by welding current to tensile strength, with the remaining 2 of the 3 factors being voltage and the wire feed rate. Welding voltage, on the contrary, had the highest impact on hardness, and so did the wire feed rate and the current rate. The best parameter conditions of maximum hardness were determined to be at 30 V, 160 A, and 6 m/min, whereas the optimal conditions of maximum tensile strength were 30 V, 170 A, and 2 m/min. The microstructural examination showed the weld zone to have fine grains of ferrite and pearlite, which meant that the metallurgical standard was high. This paper focuses on the importance of optimizing the process to achieve high-quality welds and also highlights the appropriateness of MIG welding for precision and automated welding.
- 15 July 2025
- Published by International Academic Publishing House
- Vol. 1 (3) , 34-43
Open AccessExperimental Evaluation of Key Welding Process Parameters on the Performance of MIG Welded Mild Steel
The implementation of innovative techniques and sophisticated procedures in welding enhances efficiency and productivity. Automation, particularly robot assisted automation, is crucial in the development of advanced welding systems. In contrast to traditional Gas Metal Arc Welding (GMAW), contemporary methods enable reduced thermal input, maintaining the workpiece and weld areas at relatively lower temperatures. This reduced heat input not only minimizes thermal distortion but also improves weld precision, reduces spatter, and enables the successful joining of mild steel, galvanized sheets, and dissimilar metals, such as steel and aluminium. In this regard, this current research paper proposes to unearth the effect of the three parameters that are attributed to considerable input of metal and influence on the mechanical performance of Metal Inert Gas (MIG) welded mild steel joints, such as current, voltage, and wire feed speed. Weld strength was assessed by mechanical properties such as tensile strength, hardness, and microstructural characteristics. The techniques employed in underpinning the experiments were drawn using a Taguchi L9 orthogonal array and three uses of three-level input parameters. ANOVA results demonstrated that the strongest influence was made by welding current to tensile strength, with the remaining 2 of the 3 factors being voltage and the wire feed rate. Welding voltage, on the contrary, had the highest impact on hardness, and so did the wire feed rate and the current rate. The best parameter conditions of maximum hardness were determined to be at 30 V, 160 A, and 6 m/min, whereas the optimal conditions of maximum tensile strength were 30 V, 170 A, and 2 m/min. The microstructural examination showed the weld zone to have fine grains of ferrite and pearlite, which meant that the metallurgical standard was high. This paper focuses on the importance of optimizing the process to achieve high-quality welds and also highlights the appropriateness of MIG welding for precision and automated welding.
- 24 April 2025
- Published by World Scientific Pub Co Pte Ltd in Journal of Molecular and Engineering Materials
- Vol. 13 (04)
Parametric Investigation on Laser Beam Welding of Aluminum Alloy 5052-H32 using Finite Element Analysis
The primary issues with welded components are heat-affected zones (HAZ) and residual stresses, which may compromise the structural and component integrity. Its determination is fairly sophisticated and may prove to be a challenging endeavor, regardless of whether it is based on numerical simulations or experimental methods. Predicting the longitudinal residual Von Mises stress distribution theoretically is made possible by this study, which is based on a parameterized multi-source model for thermal field modeling in laser welding followed by experimental validation. To simulate the welding process and the intermediate performance indicators (IPIs), (peak temperature, HAZ volume, cooling rate and structural deformation), a three-dimensional heat transfer model is built using the finite element approach. Among the IPIs, the weld quality is indicated by the cooling rate and HAZ volume, while the welding mode is shown by the peak temperature. In order to quickly calculate IPIs instead of requiring lengthy numerical simulations, a regression relationship is built between the parameters of the welding process and the IPIs.
- 24 April 2025
- Published by World Scientific Pub Co Pte Ltd in Journal of Molecular and Engineering Materials
- Vol. 13 (04)
Parametric Investigation on Laser Beam Welding of Aluminum Alloy 5052-H32 using Finite Element Analysis
The primary issues with welded components are heat-affected zones (HAZ) and residual stresses, which may compromise the structural and component integrity. Its determination is fairly sophisticated and may prove to be a challenging endeavor, regardless of whether it is based on numerical simulations or experimental methods. Predicting the longitudinal residual Von Mises stress distribution theoretically is made possible by this study, which is based on a parameterized multi-source model for thermal field modeling in laser welding followed by experimental validation. To simulate the welding process and the intermediate performance indicators (IPIs), (peak temperature, HAZ volume, cooling rate and structural deformation), a three-dimensional heat transfer model is built using the finite element approach. Among the IPIs, the weld quality is indicated by the cooling rate and HAZ volume, while the welding mode is shown by the peak temperature. In order to quickly calculate IPIs instead of requiring lengthy numerical simulations, a regression relationship is built between the parameters of the welding process and the IPIs.
- 31 December 2024
- Published by Springer Nature
- p. 457-470
Exploring Kerf Width in Wire EDM of EN36B Steel: A Statistical Analysis
- 31 December 2024
- Published by Springer Nature
- p. 457-470
Exploring Kerf Width in Wire EDM of EN36B Steel: A Statistical Analysis
- 31 December 2024
- Published by Springer Nature
- p. 565-579
Multi-criteria Decision-Making for Laser Metal-Polymer Welding: A MACONT Approach
- 31 December 2024
- Published by Springer Nature
- p. 565-579
Multi-criteria Decision-Making for Laser Metal-Polymer Welding: A MACONT Approach
- 12 February 2024
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 56 (4) , 1-35
Sensitivity analysis on surface topography for laser-surface-texturing of Hastelloy C-276 superalloy: studies on micro-structure morphology characterization
- 12 February 2024
- Published by Springer Nature in Optical and Quantum Electronics
- Vol. 56 (4) , 1-35
Sensitivity analysis on surface topography for laser-surface-texturing of Hastelloy C-276 superalloy: studies on micro-structure morphology characterization
- 1 January 2021
- Published by IGI Global Scientific Publishing
- p. 137-159
Laser Trepan Drilling of Monel k-500 Superalloy in Low Power Laser Beam Machining
In the field of micro processing of materials, laser has great importance as a source of heat and for its ability to deliver a coherent beam. The use of 50-watt average power for through-hole is impossible to achieve good quality drilling of the metal sheet upto 2 mm thickness. But the use of unique parameter sawing angle and constant focal point distance plays a significant role on hole diameter and circularity in laser trepan drilling. In the present research study, laser trepan drilling is investigated through multi diode pulsed fiber laser beam machining. Experimental analysis based on central composite design (CCD) of response surface methodology (RSM) has been fulfilled to find out the mathematical model. A study of the effect of sawing angle with other process parameters such as cutting speed, power, duty cycle, and pulse frequency on overcut bottom diameter and circularity at bottom for a monel k-500 has been conducted. Experimental validation of the proposed model shows that desired hole quality can be obtained by optimization of controllable of suitable process parameters.
- 1 January 2021
- Published by IGI Global Scientific Publishing
- p. 137-159
Laser Trepan Drilling of Monel k-500 Superalloy in Low Power Laser Beam Machining
In the field of micro processing of materials, laser has great importance as a source of heat and for its ability to deliver a coherent beam. The use of 50-watt average power for through-hole is impossible to achieve good quality drilling of the metal sheet upto 2 mm thickness. But the use of unique parameter sawing angle and constant focal point distance plays a significant role on hole diameter and circularity in laser trepan drilling. In the present research study, laser trepan drilling is investigated through multi diode pulsed fiber laser beam machining. Experimental analysis based on central composite design (CCD) of response surface methodology (RSM) has been fulfilled to find out the mathematical model. A study of the effect of sawing angle with other process parameters such as cutting speed, power, duty cycle, and pulse frequency on overcut bottom diameter and circularity at bottom for a monel k-500 has been conducted. Experimental validation of the proposed model shows that desired hole quality can be obtained by optimization of controllable of suitable process parameters.