Mohamed Saad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Mohamed Saad has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Eduard Alarcón
Universitat Politecnica de Catalunya, Barcelona, Spain
5 shared publications - Mohamed Orabi
Faculty of Engineering, Aswan University, Aswan, Egypt
4 shared publications - Ahmed Shawky
Department of Electrical Engineering, Faculty of Engineering, Aswan University, Aswan, Egypt
3 shared publications Eduard Alarcon
2 shared publicationsAshraf Lotfi
Enpirion Inc. New Jersey 08827, USA
1 shared publication- Denys Ovsiyenko
Department of Electronic Engineering, Universitat Politcnica de Catalunya, Barcelona, Spain
1 shared publication
Latest Publications
- Open Access
- 8 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 210326-210340
Power Processing Circuit With Simultaneous Frequency Tuning and Voltage Regulation: Concept Analysis, Design, and Integration Into IPT Receivers
Inductive power transfer (IPT), a magnetic-coupling-based type of wireless power transfer, faces challenges owing to resonance frequency deviations arising from component tolerances and temperature effects at either the transmitter or receiver. This work introduces a receiver-side power processing architecture that addresses detuning challenges while simultaneously maintaining a precise output voltage. The proposed solution unifies frequency tuning and voltage regulation within a single DC-DC converter, transforming a conventional back-end buck or boost stage into a four-switch buck-boost topology by adding only two additional switches. A tailored modulation strategy enables step-up and step-down voltage regulation while dynamically compensating for IPT receiver frequency shifts, all without extra passive elements, capacitors, or inductors, typically used for frequency tuning. The concept is substantiated through comprehensive mathematical modeling, integration with a series–parallel compensation network, and experimental validation on a 15 W prototype. The results demonstrate output voltage regulation and effective frequency correction that guarantees up to 8% efficiency recovery under most adverse detuning circumstances.
- 8 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 210326-210340
Open AccessPower Processing Circuit With Simultaneous Frequency Tuning and Voltage Regulation: Concept Analysis, Design, and Integration Into IPT Receivers
Inductive power transfer (IPT), a magnetic-coupling-based type of wireless power transfer, faces challenges owing to resonance frequency deviations arising from component tolerances and temperature effects at either the transmitter or receiver. This work introduces a receiver-side power processing architecture that addresses detuning challenges while simultaneously maintaining a precise output voltage. The proposed solution unifies frequency tuning and voltage regulation within a single DC-DC converter, transforming a conventional back-end buck or boost stage into a four-switch buck-boost topology by adding only two additional switches. A tailored modulation strategy enables step-up and step-down voltage regulation while dynamically compensating for IPT receiver frequency shifts, all without extra passive elements, capacitors, or inductors, typically used for frequency tuning. The concept is substantiated through comprehensive mathematical modeling, integration with a series–parallel compensation network, and experimental validation on a 15 W prototype. The results demonstrate output voltage regulation and effective frequency correction that guarantees up to 8% efficiency recovery under most adverse detuning circumstances.
- 19 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Proposal of Compact Active and Reactive Power Processing Circuit for RI-WPT Receivers
Wireless Power Transfer (WPT) concept has been realized through many technological methods to feed power in a cordless way in many applications. Among these various methods, Resonant Inductive Wireless Power Transfer RI-WPT has been extensively used to charge the batteries for consumer electronics such as smartwatches, mobile phones, and laptops. However, at high resonant frequency, this technology is vulnerable to the frequency variation in transmitter and receiver circuits, which results from components tolerance and other related factors. Frequency mismatch severely drops the conversion power efficiency and deteriorates the effectiveness of RI-WPT. To solve this issue, this paper proposes and verifies a novel active and reactive power control circuit at the receiver side of a wireless power transfer system. A 10W 127.7 kHz RIWPT receiver system is designed and verified against variations in compensation network elements, where 1. 3W is recovered after frequency re-tuning thanks to the proposed circuit.
- 19 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Proposal of Compact Active and Reactive Power Processing Circuit for RI-WPT Receivers
Wireless Power Transfer (WPT) concept has been realized through many technological methods to feed power in a cordless way in many applications. Among these various methods, Resonant Inductive Wireless Power Transfer RI-WPT has been extensively used to charge the batteries for consumer electronics such as smartwatches, mobile phones, and laptops. However, at high resonant frequency, this technology is vulnerable to the frequency variation in transmitter and receiver circuits, which results from components tolerance and other related factors. Frequency mismatch severely drops the conversion power efficiency and deteriorates the effectiveness of RI-WPT. To solve this issue, this paper proposes and verifies a novel active and reactive power control circuit at the receiver side of a wireless power transfer system. A 10W 127.7 kHz RIWPT receiver system is designed and verified against variations in compensation network elements, where 1. 3W is recovered after frequency re-tuning thanks to the proposed circuit.
- Open Access
Insights into Dynamic Tuning of Magnetic-Resonant Wireless Power Transfer Receivers Based on Switch-Mode Gyrators
Magnetic-resonant wireless power transfer (WPT) has become a reliable contactless source of power for a wide range of applications. WPT spans different power levels ranging from low-power implantable devices up to high-power electric vehicles (EV) battery charging. The transmission range and efficiency of WPT have been reasonably enhanced by resonating the transmitter and receiver coils at a common frequency. Nevertheless, matching between resonance in the transmitter and receiver is quite cumbersome, particularly in single-transmitter multi-receiver systems. The resonance frequency in transmitter and receiver tank circuits has to be perfectly matched, otherwise power transfer capability is greatly degraded. This paper discusses the mistuning effect of parallel-compensated receivers, and thereof a novel dynamic frequency tuning method and related circuit topology and control is proposed and characterized in the system application. The proposed method is based on the concept of switch-mode gyrator emulating variable lossless inductors oriented to enable self-tunability in WPT receivers.
Open AccessInsights into Dynamic Tuning of Magnetic-Resonant Wireless Power Transfer Receivers Based on Switch-Mode Gyrators
Magnetic-resonant wireless power transfer (WPT) has become a reliable contactless source of power for a wide range of applications. WPT spans different power levels ranging from low-power implantable devices up to high-power electric vehicles (EV) battery charging. The transmission range and efficiency of WPT have been reasonably enhanced by resonating the transmitter and receiver coils at a common frequency. Nevertheless, matching between resonance in the transmitter and receiver is quite cumbersome, particularly in single-transmitter multi-receiver systems. The resonance frequency in transmitter and receiver tank circuits has to be perfectly matched, otherwise power transfer capability is greatly degraded. This paper discusses the mistuning effect of parallel-compensated receivers, and thereof a novel dynamic frequency tuning method and related circuit topology and control is proposed and characterized in the system application. The proposed method is based on the concept of switch-mode gyrator emulating variable lossless inductors oriented to enable self-tunability in WPT receivers.
- Open Access
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. P.1-P.10
A PLL control for self-tuning of parallel wireless power transfer receivers utilizing switch-mode gyrator emulated inductors
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. P.1-P.10
Open AccessA PLL control for self-tuning of parallel wireless power transfer receivers utilizing switch-mode gyrator emulated inductors
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Switch-mode gyrator-based emulated inductor enabling self-tunability in WPT receivers
Magnetic resonance wireless power transfer (WPT) is a very promising technology for a wide range of applications. The transmission range and efficiency of wireless power transfer have been reasonably enhanced by resonating transmitter and receiver coil at a common frequency. The transmitter and receiver sides have to be perfectly tuned, otherwise power transfer capability is greatly reduced. This paper discusses the detuning effect of parallel compensated receivers, and thereof a novel self-tuning method and related circuit topology and control is proposed and characterized in the system application. The proposed method is based on the concept of switch-mode gyrator emulating variable lossless inductors oriented to enable self-tunability in WPT receivers.
- 1 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Switch-mode gyrator-based emulated inductor enabling self-tunability in WPT receivers
Magnetic resonance wireless power transfer (WPT) is a very promising technology for a wide range of applications. The transmission range and efficiency of wireless power transfer have been reasonably enhanced by resonating transmitter and receiver coil at a common frequency. The transmitter and receiver sides have to be perfectly tuned, otherwise power transfer capability is greatly reduced. This paper discusses the detuning effect of parallel compensated receivers, and thereof a novel self-tuning method and related circuit topology and control is proposed and characterized in the system application. The proposed method is based on the concept of switch-mode gyrator emulating variable lossless inductors oriented to enable self-tunability in WPT receivers.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1184-1189
Tunable switch-mode emulated inductive elements for enhanced power converter miniaturization
This work presents the emulation of tunable switch-mode inductive elements for power converters applications. Such elements are based on the concept of ideal loss-free realization by means of switch-mode circuits. A gyrator-based approach for synthesizing inductors is demonstrated. The value of the emulated inductance could be tuned by using appropriate control which would help to alleviate common undesirable properties of conventional passive implementations such as tolerance and value change over temperature and time. This approach enables monolithic circuits composed of semiconductor devices and small inductors/capacitors to be used to emulate large reactive components as a step forward for enhanced power converter miniaturization and integration.
- 1 October 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1184-1189
Tunable switch-mode emulated inductive elements for enhanced power converter miniaturization
This work presents the emulation of tunable switch-mode inductive elements for power converters applications. Such elements are based on the concept of ideal loss-free realization by means of switch-mode circuits. A gyrator-based approach for synthesizing inductors is demonstrated. The value of the emulated inductance could be tuned by using appropriate control which would help to alleviate common undesirable properties of conventional passive implementations such as tolerance and value change over temperature and time. This approach enables monolithic circuits composed of semiconductor devices and small inductors/capacitors to be used to emulate large reactive components as a step forward for enhanced power converter miniaturization and integration.
- 11 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 11, 642-645
On tunable switch-mode reactive networks: A gyrator-based resonator emulation
This paper introduces the concept of switch-mode tunable emulated reactive networks. The idea of implementing reactive networks based on the theory of gyrators is proposed and characterized in an application-driven design-oriented context. By means of using switch-mode power processing converters to synthesize gyrators, small capacitors or inductors are effectively multiplied to emulate larger ideally lossless reactive elements. The proposed idea enables to electronically tune the values of reactive elements by means of timing control variables. The proposed tunable reactive networks target many potential applications such as tunable-front-ends for energy harvesting, electronic compensating active power filters, and tunable-front-ends for wireless power transfer links.
- 11 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 11, 642-645
On tunable switch-mode reactive networks: A gyrator-based resonator emulation
This paper introduces the concept of switch-mode tunable emulated reactive networks. The idea of implementing reactive networks based on the theory of gyrators is proposed and characterized in an application-driven design-oriented context. By means of using switch-mode power processing converters to synthesize gyrators, small capacitors or inductors are effectively multiplied to emulate larger ideally lossless reactive elements. The proposed idea enables to electronically tune the values of reactive elements by means of timing control variables. The proposed tunable reactive networks target many potential applications such as tunable-front-ends for energy harvesting, electronic compensating active power filters, and tunable-front-ends for wireless power transfer links.
- 1 March 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10482334,p. 2098-2105
Design of integrated POL DC-DC converters based on two-stage architectures
Due to the functionality increase of modern battery-powered portable devices such as PDAs, smart phones, and notebooks etc., the battery life is an important issue. An efficient voltage regulator (VR) is a must if we need to extend the battery life. For this purpose, this paper discusses the employment of two-stage architecture on the design of point-of-load (POL) Dc-Dc converters. At first, the paper discusses the benefits of replacing the conventional one-stage buck converter by an integrated two-stage step-down converter. The design aspects of a two-stage 6V-to-1V converter are shown as an example to clarify the benefits of the design over one-stage approach. The results show that efficiency of two-stage converter is higher than the one-stage approach in addition to size and cost reduction. Then, the benefits of replacing boost converters by integrated two-stage step-up converters are discussed followed by a design example for two-stage step-up converter from 3.6V-to-12V. The results show that the two-stage approach increases the efficiency of the converter in addition to the benefits from stability point of view.
- 1 March 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10482334,p. 2098-2105
Design of integrated POL DC-DC converters based on two-stage architectures
Due to the functionality increase of modern battery-powered portable devices such as PDAs, smart phones, and notebooks etc., the battery life is an important issue. An efficient voltage regulator (VR) is a must if we need to extend the battery life. For this purpose, this paper discusses the employment of two-stage architecture on the design of point-of-load (POL) Dc-Dc converters. At first, the paper discusses the benefits of replacing the conventional one-stage buck converter by an integrated two-stage step-down converter. The design aspects of a two-stage 6V-to-1V converter are shown as an example to clarify the benefits of the design over one-stage approach. The results show that efficiency of two-stage converter is higher than the one-stage approach in addition to size and cost reduction. Then, the benefits of replacing boost converters by integrated two-stage step-up converters are discussed followed by a design example for two-stage step-up converter from 3.6V-to-12V. The results show that the two-stage approach increases the efficiency of the converter in addition to the benefits from stability point of view.
- 1 October 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02750473,p. 1-6
A novel linear-nonlinear technique for fast transient buck converter
Modern Portable devices require high performance Power Management Integrated Circuits (PMICs) for powering it. Old requirements for PMICs were high efficiency and small footprint area. However there are some applications that are also sensitive for the output voltage deviations due to sudden step-up and step-down load change. A novel nonlinear control technique that can be used side-by-side with the conventional voltage-mode linear control is proposed here. The new technique minimizes both undershoot; overshoot percentages and the transient time. It is proven by results that this new technique can help in using smaller output capacitors Co which save the PCB area.
- 1 October 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02750473,p. 1-6
A novel linear-nonlinear technique for fast transient buck converter
Modern Portable devices require high performance Power Management Integrated Circuits (PMICs) for powering it. Old requirements for PMICs were high efficiency and small footprint area. However there are some applications that are also sensitive for the output voltage deviations due to sudden step-up and step-down load change. A novel nonlinear control technique that can be used side-by-side with the conventional voltage-mode linear control is proposed here. The new technique minimizes both undershoot; overshoot percentages and the transient time. It is proven by results that this new technique can help in using smaller output capacitors Co which save the PCB area.