Jaivindra Singh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jaivindra Singh has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
Kanwer Singh Arora
Research & Development, Tata Steel Limited Jamshedpur, Jharkhand, India
6 shared publications- Kanwer Singh Arora
Tata Steel Limited, Jamshedpur, India
5 shared publications - Dinesh Kumar Shukla
Dr BR Ambedkar Natl Inst Technol, Dept Mech Engn, Jalandhar 144008, India
4 shared publications Brajesh Asati
Research & Development, Tata Steel Limited, Jamshedpur, India
3 shared publicationsDinesh Kumar Shukla
Department of Mechanical Engineering, Dr. B. R. Ambedkar National Institute of Technology, Jalandhar, India
3 shared publications- Joao Pedro Oliveira
CENIMAT/I3N, Department of Materials Science, NOVA School of Science and Technology, Universidade NOVA de Lisboa, Caparica, Portugal
3 shared publications
Latest Publications
- Open Access
- 4 February 2026
- Published by AccScience Publishing in Engineering Science in Additive Manufacturing
- Vol. 2 (1) , 025420029
Understanding melt pool characteristics as a means for reducing build layout quality variations in laser-based powder bed fusion: An approach toward spatial parameter compensations
This study investigates the impact of build platform location on melt pool variability during laser-based powder bed fusion of metals. The incident angle and gas flow are hypothesized to influence melt pool penetration and contribute to spatial variations in the melt pool. Results show that the typical build strategy using the same material-dependent processing parameters for all parts throughout the build chamber produces parts with location-dependent properties. An overarching goal of the present work was to attempt to fabricate similar parts at different locations within the build chamber by identifying processing parameters that produce similar melt pool depths at these locations. It was further hypothesized that by normalizing process parameters through similar melt pool depths, similar porosity counts could be achieved at these locations, thus mitigating process-induced variability. The study emphasizes the necessity of spatial parameter adjustments to minimize variability across different locations within the build platform, as well as the requirement for uniform gas flow across the build chamber, thereby eliminating gas flow-dependent variations from the analysis.
- 4 February 2026
- Published by AccScience Publishing in Engineering Science in Additive Manufacturing
- Vol. 2 (1) , 025420029
Open AccessUnderstanding melt pool characteristics as a means for reducing build layout quality variations in laser-based powder bed fusion: An approach toward spatial parameter compensations
This study investigates the impact of build platform location on melt pool variability during laser-based powder bed fusion of metals. The incident angle and gas flow are hypothesized to influence melt pool penetration and contribute to spatial variations in the melt pool. Results show that the typical build strategy using the same material-dependent processing parameters for all parts throughout the build chamber produces parts with location-dependent properties. An overarching goal of the present work was to attempt to fabricate similar parts at different locations within the build chamber by identifying processing parameters that produce similar melt pool depths at these locations. It was further hypothesized that by normalizing process parameters through similar melt pool depths, similar porosity counts could be achieved at these locations, thus mitigating process-induced variability. The study emphasizes the necessity of spatial parameter adjustments to minimize variability across different locations within the build platform, as well as the requirement for uniform gas flow across the build chamber, thereby eliminating gas flow-dependent variations from the analysis.
- 25 November 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 141 (12) , 6117-6130
Effect of pre- and post-heat pulses on dynamic contact resistance, nugget formation, and mechanical performance in three-sheet resistance spot welding of DP780 steel
- 25 November 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 141 (12) , 6117-6130
Effect of pre- and post-heat pulses on dynamic contact resistance, nugget formation, and mechanical performance in three-sheet resistance spot welding of DP780 steel
- 11 March 2025
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 147 (6) , 1-30
Role of Particle Size Distribution on Microstructure, Defects, and Mechanical Properties in Laser-Based Powder Bed Fusion of Scalmalloy®
This study investigates the impact of particle size distribution (PSD) in Scalmalloy® powder feedstocks on the geometrical accuracy, microstructure, defect formation, and mechanical properties of test artifacts fabricated via laser-based powder bed fusion of metals (PBF-LB/M). Two powder feedstocks were analyzed: Powder-1, with a mean particle size of 29.30–29.72 µm and a narrower, more uniform PSD, and Powder-2, with a mean particle size of 40.80–41.53 µm and a broader, more heterogeneous PSD. Powder-2 produced artifacts with improved geometrical accuracy and surface finish but exhibited cracking in both lattice (small features) and bulk regions. Scanning electron microscopy revealed Si precipitation near cracks in the lattice regions, attributed to segregation caused by heat accumulation in thin features and the coarser, more heterogeneous PSD of Powder-2. Powder-2 samples exhibited higher strain at a break during tensile testing, likely due to its lower porosity compared to Powder-1. Single-line and hatch scan results indicated no cracking for either powder, highlighting the susceptibility of small features to thermal gradients, segregation, and geometric stress concentrators. The observation of cracking exclusively in the thin features, and not in the bulk regions, underscores the artifact's utility in investigating how geometrical features influence thermal fields, microstructural evolution, and ultimately, performance in PBF-LB/M processes.
- 11 March 2025
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 147 (6) , 1-30
Role of Particle Size Distribution on Microstructure, Defects, and Mechanical Properties in Laser-Based Powder Bed Fusion of Scalmalloy®
This study investigates the impact of particle size distribution (PSD) in Scalmalloy® powder feedstocks on the geometrical accuracy, microstructure, defect formation, and mechanical properties of test artifacts fabricated via laser-based powder bed fusion of metals (PBF-LB/M). Two powder feedstocks were analyzed: Powder-1, with a mean particle size of 29.30–29.72 µm and a narrower, more uniform PSD, and Powder-2, with a mean particle size of 40.80–41.53 µm and a broader, more heterogeneous PSD. Powder-2 produced artifacts with improved geometrical accuracy and surface finish but exhibited cracking in both lattice (small features) and bulk regions. Scanning electron microscopy revealed Si precipitation near cracks in the lattice regions, attributed to segregation caused by heat accumulation in thin features and the coarser, more heterogeneous PSD of Powder-2. Powder-2 samples exhibited higher strain at a break during tensile testing, likely due to its lower porosity compared to Powder-1. Single-line and hatch scan results indicated no cracking for either powder, highlighting the susceptibility of small features to thermal gradients, segregation, and geometric stress concentrators. The observation of cracking exclusively in the thin features, and not in the bulk regions, underscores the artifact's utility in investigating how geometrical features influence thermal fields, microstructural evolution, and ultimately, performance in PBF-LB/M processes.
- Open Access
- 2 October 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 135 (1-2) , 155
Correction: Comparative analysis of MIG brazing modes: Process stability, bead morphology, microstructure, and mechanical properties
- 2 October 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 135 (1-2) , 155
Open AccessCorrection: Comparative analysis of MIG brazing modes: Process stability, bead morphology, microstructure, and mechanical properties
- 21 September 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 135 (1-2) , 137-154
Comparative analysis of MIG brazing modes: process stability, bead morphology, microstructure, and mechanical properties
- 21 September 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 135 (1-2) , 137-154
Comparative analysis of MIG brazing modes: process stability, bead morphology, microstructure, and mechanical properties
- Open Access
- 6 June 2024
- Published by Springer Nature in Research Square
Comparative Analysis of MIG Brazing Modes: Process Stability, Bead Morphology, Microstructure, and Mechanical Properties
This study compares various modes of metal inert gas (MIG) brazing concerning process stability, bead morphology, microstructure, and mechanical properties. The pulsed-MIG process produces joints with flatter and wider bead morphology, indicating better wettability compared to cold metal transfer (CMT) and standard-MIG processes. This difference is due to the higher heat input of the pulsed-MIG process at the same wire feed rate (WFR). Analysis of voltage-current signals, probability distribution curves, and cyclograms reveals that the CMT-MIG process is the most stable and defect-free, while the standard-MIG process becomes less stable with increasing WFR. Joints brazed using the pulsed-MIG process have significantly higher shear-tensile strength compared to the other two modes, primarily due to higher wettability. Three modes of failure—horizontal interface (mode 1), vertical interface and bead (mode 2), and base metal (mode 3)—were observed. Excessive wettability reduces the cross-sectional area, negatively impacting static and dynamic performance, especially in pulsed brazing joints under high load amplitudes. Conversely, the bumpy beads in CMT and standard-MIG processes enhance the cross-sectional area, providing better resistance against failure along the vertical interface and bead. This study offers a comprehensive database and guidance for selecting appropriate brazing methods depending on joint application, considering the limitations of each brazing process.
- 6 June 2024
- Published by Springer Nature in Research Square
Open AccessComparative Analysis of MIG Brazing Modes: Process Stability, Bead Morphology, Microstructure, and Mechanical Properties
This study compares various modes of metal inert gas (MIG) brazing concerning process stability, bead morphology, microstructure, and mechanical properties. The pulsed-MIG process produces joints with flatter and wider bead morphology, indicating better wettability compared to cold metal transfer (CMT) and standard-MIG processes. This difference is due to the higher heat input of the pulsed-MIG process at the same wire feed rate (WFR). Analysis of voltage-current signals, probability distribution curves, and cyclograms reveals that the CMT-MIG process is the most stable and defect-free, while the standard-MIG process becomes less stable with increasing WFR. Joints brazed using the pulsed-MIG process have significantly higher shear-tensile strength compared to the other two modes, primarily due to higher wettability. Three modes of failure—horizontal interface (mode 1), vertical interface and bead (mode 2), and base metal (mode 3)—were observed. Excessive wettability reduces the cross-sectional area, negatively impacting static and dynamic performance, especially in pulsed brazing joints under high load amplitudes. Conversely, the bumpy beads in CMT and standard-MIG processes enhance the cross-sectional area, providing better resistance against failure along the vertical interface and bead. This study offers a comprehensive database and guidance for selecting appropriate brazing methods depending on joint application, considering the limitations of each brazing process.
- 28 April 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 236 (12) , 2506-2515
Mechanical and microstructural characterization of cold metal transfer (CMT) spot aluminium-steel weld-brazed joints
The aim of this work is to optimize the process parameters and to analyze the evolution of mechanical and microstructural properties during CMT spot weld-brazing of dissimilar materials aluminium-steel. In doing so, process parameters including hold time, hole diameter and pre-setting gap were optimized using Taguchi orthogonal design and then the microstructure of the interfacial region was characterized using optical microscopy, scanning electron microscopy and X-ray diffraction. Shear-tensile testing was performed to evaluate the load-bearing capacity of the joints. It was observed that the strength of spot weld-brazed joints is primarily dependent on the interfacial area and intermetallic compounds at the interface. High hold time and wider hole diameter resulted in poor joint strength due to excessive intermetallic formation and an unfilled region in the joint. In addition, Cyclogram revealed that the joining process was comparatively unstable for the wider hole and high hold time due to the formation of zinc fumes. The provision of a pre-setting gap in between the sheets showed a positive impact on the joint strength.
- 28 April 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 236 (12) , 2506-2515
Mechanical and microstructural characterization of cold metal transfer (CMT) spot aluminium-steel weld-brazed joints
The aim of this work is to optimize the process parameters and to analyze the evolution of mechanical and microstructural properties during CMT spot weld-brazing of dissimilar materials aluminium-steel. In doing so, process parameters including hold time, hole diameter and pre-setting gap were optimized using Taguchi orthogonal design and then the microstructure of the interfacial region was characterized using optical microscopy, scanning electron microscopy and X-ray diffraction. Shear-tensile testing was performed to evaluate the load-bearing capacity of the joints. It was observed that the strength of spot weld-brazed joints is primarily dependent on the interfacial area and intermetallic compounds at the interface. High hold time and wider hole diameter resulted in poor joint strength due to excessive intermetallic formation and an unfilled region in the joint. In addition, Cyclogram revealed that the joining process was comparatively unstable for the wider hole and high hold time due to the formation of zinc fumes. The provision of a pre-setting gap in between the sheets showed a positive impact on the joint strength.
- 26 March 2022
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 75 (7) , 1929-1940
Multi-objective Optimization of Process Parameters during Dissimilar Cold Metal Transfer Weld-Brazing of Al-Steel
- 26 March 2022
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 75 (7) , 1929-1940
Multi-objective Optimization of Process Parameters during Dissimilar Cold Metal Transfer Weld-Brazing of Al-Steel
- 28 September 2020
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 143 (1) , 1-15
Influence of Novel Torch Type on Mechanical and Microstructural Characteristics of Cold Metal Transfer Brazed Joints
The present study aimed to braze interstitial free (IF) steel by using novel Braze+ and conventional Robacta torches with the aid of CuAl8 filler wire for a range of heat input 72–250 J/mm. Results showed that focused/denser arc and smaller arc action range, i.e., lower heat loss in the case of Braze+ torch resulted in better wettability, thicker intermetallic layer at the interface of deposited bead-steel, and higher dispersive phase fraction in the bead compared to Robacta torch which ultimately contributed to the evolution of mechanical properties of brazed joints. Furthermore, wettability, thickness of intermetallic layer and fraction of dispersive phases increased with the heat input due to increased deposition rate per unit time, availability of reacting atoms near the interface, and melting of base metal, respectively. Hardness variation of the brazed joints revealed that base metal was prone to failure due to comparatively higher hardness as well as improved resistance to failure of HAZ (due to the formation of acicular ferrite) and deposited bead (due to dispersion hardening). In addition, Fe, Al, and Cu were the main constituents of intermetallic layer and dispersive phases in the bead. IMC layer was harder in the case of Braze+ torch due to comparatively higher Fe content. Two modes of failure namely interface (brittle features) and base metal (ductile features) were observed during shear-tensile testing.
- 28 September 2020
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 143 (1) , 1-15
Influence of Novel Torch Type on Mechanical and Microstructural Characteristics of Cold Metal Transfer Brazed Joints
The present study aimed to braze interstitial free (IF) steel by using novel Braze+ and conventional Robacta torches with the aid of CuAl8 filler wire for a range of heat input 72–250 J/mm. Results showed that focused/denser arc and smaller arc action range, i.e., lower heat loss in the case of Braze+ torch resulted in better wettability, thicker intermetallic layer at the interface of deposited bead-steel, and higher dispersive phase fraction in the bead compared to Robacta torch which ultimately contributed to the evolution of mechanical properties of brazed joints. Furthermore, wettability, thickness of intermetallic layer and fraction of dispersive phases increased with the heat input due to increased deposition rate per unit time, availability of reacting atoms near the interface, and melting of base metal, respectively. Hardness variation of the brazed joints revealed that base metal was prone to failure due to comparatively higher hardness as well as improved resistance to failure of HAZ (due to the formation of acicular ferrite) and deposited bead (due to dispersion hardening). In addition, Fe, Al, and Cu were the main constituents of intermetallic layer and dispersive phases in the bead. IMC layer was harder in the case of Braze+ torch due to comparatively higher Fe content. Two modes of failure namely interface (brittle features) and base metal (ductile features) were observed during shear-tensile testing.
- 1 September 2020
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 283
Lap weld-brazing of aluminium to steel using novel cold metal transfer process
- 1 September 2020
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 283
Lap weld-brazing of aluminium to steel using novel cold metal transfer process