Shuo Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shuo Wang has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Bin Qi
Beijing Technology and Business University
1 shared publication - Dong Han
School of Material and Mechanical Engineering, Beijing Technology and Business University, Beijing 100048, China
1 shared publication - Feifei Zhang
School of Material and Mechanical Engineering, Beijing Technology and Business University, Beijing 100048, China
1 shared publication - Jin Yang
School of Material and Mechanical Engineering, Beijing Technology and Business University, Beijing 100048, China
1 shared publication - Wentian Shi
Department of Mechanical Engineering, Beijing Technology and Business University, Beijing, China
1 shared publication - Yingyi Ma
School of Material and Mechanical Engineering, Beijing Technology and Business University, Beijing 100048, China
1 shared publication
Latest Publications
- Open Access
Research on High Layer Thickness Fabricated of 316L by Selective Laser Melting
Selective laser melting (SLM) is a potential additive manufacturing (AM) technology. However, the application of SLM was confined due to low efficiency. To improve efficiency, SLM fabrication with a high layer thickness and fine powder was systematically researched, and the void areas and hollow powders can be reduced by using fine powder. Single-track experiments were used to narrow down process parameter windows. Multi-layer fabrication relative density can be reached 99.99% at the exposure time-point distance-hatch space of 120 μs-40 μm-240 μm. Also, the building rate can be up to 12 mm3/s, which is about 3–10 times higher than the previous studies. Three typical defects were found by studying deeply, including the un-melted defect between the molten pools, the micro-pore defect within the molten pool, and the irregular distribution of the splashing phenomenon. Moreover, the microstructure is mostly equiaxed crystals and a small amount of columnar crystals. The averages of ultimate tensile strength, yield strength, and elongation are 625 MPa, 525 MPa, and 39.9%, respectively. As exposure time increased from 80 μs to 200 μs, the grain size is gradually grown up from 0.98 μm to 2.23 μm, the grain aspect ratio is close to 1, and the tensile properties are shown as a downward trend. The tensile properties of high layer thickness fabricated are not significantly different than those with a coarse-powder layer thickness of low in previous research.
Open AccessResearch on High Layer Thickness Fabricated of 316L by Selective Laser Melting
Selective laser melting (SLM) is a potential additive manufacturing (AM) technology. However, the application of SLM was confined due to low efficiency. To improve efficiency, SLM fabrication with a high layer thickness and fine powder was systematically researched, and the void areas and hollow powders can be reduced by using fine powder. Single-track experiments were used to narrow down process parameter windows. Multi-layer fabrication relative density can be reached 99.99% at the exposure time-point distance-hatch space of 120 μs-40 μm-240 μm. Also, the building rate can be up to 12 mm3/s, which is about 3–10 times higher than the previous studies. Three typical defects were found by studying deeply, including the un-melted defect between the molten pools, the micro-pore defect within the molten pool, and the irregular distribution of the splashing phenomenon. Moreover, the microstructure is mostly equiaxed crystals and a small amount of columnar crystals. The averages of ultimate tensile strength, yield strength, and elongation are 625 MPa, 525 MPa, and 39.9%, respectively. As exposure time increased from 80 μs to 200 μs, the grain size is gradually grown up from 0.98 μm to 2.23 μm, the grain aspect ratio is close to 1, and the tensile properties are shown as a downward trend. The tensile properties of high layer thickness fabricated are not significantly different than those with a coarse-powder layer thickness of low in previous research.