In-Tae Seo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
In-Tae Seo has a total of 106 co-authors. Here are the top co-authors by number of shared publications:
- Sahn Nahm
Department of Materials Science and Engineering Korea University Seoul Republic of Korea
20 shared publications Sahn Nahm
12 shared publicationsJae-Hong Choi
6 shared publicationsJoon Hur
6 shared publicationsBo-Yun Kim
5 shared publicationsBo‐Yun Kim
Information Technology‐Nano Science KU‐KIST Graduate School of Converging Science and Technology 1‐5Ga, Anam‐Dong Seongbuk‐Gu Seoul 136‐713 Korea
5 shared publications
Latest Publications
- 4 April 2018
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 6 (17) , 4769-4776
Optimizing the defect chemistry of Na1/2Bi1/2TiO3-based materials: paving the way for excellent high temperature capacitors
For applications in automotive, aviation and renewable energy industries temperature and power requirements have been significantly increased for electronic components. In particular, capacitors have been identified as the most critical materials considering the fulfillment of these requirements. Ceramics are the most promising materials for high temperature capacitors but no ceramic has been able to meet the necessary electrical properties so far. In this work, Na1/2Bi1/2TiO3 (NBT) solid solutions are investigated to optimize the respective electrical properties. A reduction of bismuth vacancy and oxygen vacancy concentration by increasing the initial Bi content leads to a significant decrease in dielectric loss. Additionally, energy efficiencies of up to 97% can be achieved for the composition Na1/2Bi1/2O3–BaTiO3–CaZrO3 (NBT–BT–CZ) and the temperature range of stable high permittivity together with low dielectric loss (tan δ ≤ 0.02) extends from −67 °C to 362 °C. Hence, optimization of the defect chemistry of NBT-materials results in highly stable electrical properties over a large temperature and electric field range, which leads to the fulfillment of industrial requirements.
- 4 April 2018
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 6 (17) , 4769-4776
Optimizing the defect chemistry of Na1/2Bi1/2TiO3-based materials: paving the way for excellent high temperature capacitors
For applications in automotive, aviation and renewable energy industries temperature and power requirements have been significantly increased for electronic components. In particular, capacitors have been identified as the most critical materials considering the fulfillment of these requirements. Ceramics are the most promising materials for high temperature capacitors but no ceramic has been able to meet the necessary electrical properties so far. In this work, Na1/2Bi1/2TiO3 (NBT) solid solutions are investigated to optimize the respective electrical properties. A reduction of bismuth vacancy and oxygen vacancy concentration by increasing the initial Bi content leads to a significant decrease in dielectric loss. Additionally, energy efficiencies of up to 97% can be achieved for the composition Na1/2Bi1/2O3–BaTiO3–CaZrO3 (NBT–BT–CZ) and the temperature range of stable high permittivity together with low dielectric loss (tan δ ≤ 0.02) extends from −67 °C to 362 °C. Hence, optimization of the defect chemistry of NBT-materials results in highly stable electrical properties over a large temperature and electric field range, which leads to the fulfillment of industrial requirements.
- 7 August 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 5 (35) , 8958-8965
Ionic conductivity of acceptor doped sodium bismuth titanate: influence of dopants, phase transitions and defect associates
We investigate both, experimentally and theoretically, the electrical conductivity of Mg- and Fe-doped polycrystalline Na0.5Bi0.5TiO3. Samples with up to 4% of acceptor dopants are studied by means of impedance spectroscopy, scanning electron microscopy, and X-ray diffraction, while an analytical defect chemical model is developed for describing the measured conductivities. Within the framework of defect chemistry, we demonstrate that the experimentally measured conductivities can only be reproduced, if the formation of dopant–vacancy defect complexes is considered and the phase transition from a rhombohedral to a tetragonal symmetry is taken into account, affecting the dissociation of the dopant–vacancy complex. By using migration energies from density functional theory calculations, we obtain a good agreement between the data obtained from the analytical model and the experimental results, if we assume that the association energy is strongly affected by the dopant concentration.
- 7 August 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 5 (35) , 8958-8965
Ionic conductivity of acceptor doped sodium bismuth titanate: influence of dopants, phase transitions and defect associates
We investigate both, experimentally and theoretically, the electrical conductivity of Mg- and Fe-doped polycrystalline Na0.5Bi0.5TiO3. Samples with up to 4% of acceptor dopants are studied by means of impedance spectroscopy, scanning electron microscopy, and X-ray diffraction, while an analytical defect chemical model is developed for describing the measured conductivities. Within the framework of defect chemistry, we demonstrate that the experimentally measured conductivities can only be reproduced, if the formation of dopant–vacancy defect complexes is considered and the phase transition from a rhombohedral to a tetragonal symmetry is taken into account, affecting the dissociation of the dopant–vacancy complex. By using migration energies from density functional theory calculations, we obtain a good agreement between the data obtained from the analytical model and the experimental results, if we assume that the association energy is strongly affected by the dopant concentration.
- 1 April 2017
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 37 (4) , 1429-1436
The effect of A site non-stoichiometry on 0.94(NayBix)TiO3-0.06BaTiO3
- 1 April 2017
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 37 (4) , 1429-1436
The effect of A site non-stoichiometry on 0.94(NayBix)TiO3-0.06BaTiO3
- Open Access
- 31 March 2016
- Published by Korean Ceramic Society in Journal of the Korean Ceramic Society
- Vol. 53 (2) , 129-133
Effect of MnO2 Addition on Microstructure and Piezoelectric Properties of 0.95(Na0.5K0.5)NbO3-0.05CaTiO3 Piezoelectric Ceramics
- 31 March 2016
- Published by Korean Ceramic Society in Journal of the Korean Ceramic Society
- Vol. 53 (2) , 129-133
Open AccessEffect of MnO2 Addition on Microstructure and Piezoelectric Properties of 0.95(Na0.5K0.5)NbO3-0.05CaTiO3 Piezoelectric Ceramics
- 1 February 2016
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 238, 71-79
Multilayer piezoelectric haptic actuator with CuO-modified PZT-PZNN ceramics
- 1 February 2016
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 238, 71-79
Multilayer piezoelectric haptic actuator with CuO-modified PZT-PZNN ceramics
- 22 December 2015
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 99 (3) , 938-945
Large Strain in CuO‐added (Na 0.2 K 0.8 )NbO 3 Ceramic for Use in Piezoelectric Multilayer Actuators
In this study, 1.0 mol% CuO‐added (Na x K 1− x )NbO 3 ( CN x K 1− x N) ceramics with 0.0 ≤ x ≤ 0.5 were sintered at a relatively low temperature of 960°C. A large Q m value (≥1750) was obtained for the specimens with x ≤ 0.2 owing to the hardening effect of Cu 2+ ions, indicating that a large number of Cu 2+ ions had replaced Nb 5+ ions in these ceramics. The double polarization versus electric field ( P – E ) hysteresis loop was observed for the specimens with x ≤ 0.2, and was explained by the defect polarization ( P d ) formed between Cu 2+ ions and O 2− vacancies. These specimens also exhibited a sprout‐shaped strain versus electric field ( S – E ) curves with a large strain of 0.14%–0.15% at 8.0 kV/mm because of the internal bias field produced by P d . For the CN 0.2 K 0.8 N ceramic, a double P – E hysteresis loop was maintained at 125°C without remnant polarization. Moreover, this ceramic showed a large strain of 0.175% after 10 4 cycles when a high electric field of 8.0 kV/mm was continuously applied to the specimens during each cycles. Therefore, CN 0.2 K 0.8 N is a useful lead‐free piezoelectric ceramic for multilayer actuators.
- 22 December 2015
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 99 (3) , 938-945
Large Strain in CuO‐added (Na 0.2 K 0.8 )NbO 3 Ceramic for Use in Piezoelectric Multilayer Actuators
In this study, 1.0 mol% CuO‐added (Na x K 1− x )NbO 3 ( CN x K 1− x N) ceramics with 0.0 ≤ x ≤ 0.5 were sintered at a relatively low temperature of 960°C. A large Q m value (≥1750) was obtained for the specimens with x ≤ 0.2 owing to the hardening effect of Cu 2+ ions, indicating that a large number of Cu 2+ ions had replaced Nb 5+ ions in these ceramics. The double polarization versus electric field ( P – E ) hysteresis loop was observed for the specimens with x ≤ 0.2, and was explained by the defect polarization ( P d ) formed between Cu 2+ ions and O 2− vacancies. These specimens also exhibited a sprout‐shaped strain versus electric field ( S – E ) curves with a large strain of 0.14%–0.15% at 8.0 kV/mm because of the internal bias field produced by P d . For the CN 0.2 K 0.8 N ceramic, a double P – E hysteresis loop was maintained at 125°C without remnant polarization. Moreover, this ceramic showed a large strain of 0.175% after 10 4 cycles when a high electric field of 8.0 kV/mm was continuously applied to the specimens during each cycles. Therefore, CN 0.2 K 0.8 N is a useful lead‐free piezoelectric ceramic for multilayer actuators.
- 12 December 2015
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 99 (3) , 796-801
Synthesis of [10Ῑ]‐Oriented (Na1−xKx)NbO3 Platelets by Using Hydrothermally Produced (K8−8xNa8x)Nb6O19·nH2O Precursor
Micrometer size [10 ] (N 1− x K x )NbO 3 ( NKN ) platelets were synthesized by annealing (K 8−8 x Na 8 x )Nb 6 O 19 · n H 2 O ( KNNH ) precursors at 500°C. The plate‐like KNNH precursors were produced from (1− y )NaOH‐ y KOH + Nb 2 O 5 specimens using the hydrothermal process at 160°C. The size of the NKN platelets was similar to that of the KNNH precursor, but the surfaces of the NKN platelets were rough while the KNNH precursor had a smooth surface. The formation of a rough surface is related to the vigorous evaporation of the H 2 O from the KNNH platelets during the annealing process at high temperatures. NKN platelets with smooth surfaces could be synthesized using KNNH platelets, which were heated to 150°C to evaporate H 2 O before annealing at 500°C. These NKN platelets can be used for the fabrication of textured NKN ceramics.
- 12 December 2015
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 99 (3) , 796-801
Synthesis of [10Ῑ]‐Oriented (Na1−xKx)NbO3 Platelets by Using Hydrothermally Produced (K8−8xNa8x)Nb6O19·nH2O Precursor
Micrometer size [10 ] (N 1− x K x )NbO 3 ( NKN ) platelets were synthesized by annealing (K 8−8 x Na 8 x )Nb 6 O 19 · n H 2 O ( KNNH ) precursors at 500°C. The plate‐like KNNH precursors were produced from (1− y )NaOH‐ y KOH + Nb 2 O 5 specimens using the hydrothermal process at 160°C. The size of the NKN platelets was similar to that of the KNNH precursor, but the surfaces of the NKN platelets were rough while the KNNH precursor had a smooth surface. The formation of a rough surface is related to the vigorous evaporation of the H 2 O from the KNNH platelets during the annealing process at high temperatures. NKN platelets with smooth surfaces could be synthesized using KNNH platelets, which were heated to 150°C to evaporate H 2 O before annealing at 500°C. These NKN platelets can be used for the fabrication of textured NKN ceramics.
- 24 August 2015
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 234, 9-16
Effect of CuO on the ferroelectric and piezoelectric properties of lead-free KNbO3 ceramics
- 24 August 2015
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 234, 9-16
Effect of CuO on the ferroelectric and piezoelectric properties of lead-free KNbO3 ceramics
- 13 June 2015
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 98 (9) , 2887-2893
Structural and Piezoelectric Properties of (1− x )Pb(Zr 1− y Ti y )O 3 – x Pb(Zn 0.4 Ni 0.6 ) 1/3 Nb 2/3 O 3 Ceramics Near Triple Point
The crystal structure and piezoelectric properties of (1− x )Pb(Zr 1− y Ti y )O 3 ‐ x Pb(Zn 0.4 Ni 0.6 ) 1/3 Nb 2/3 O 3 [(1− x ) PZ 1− y T y ‐ x PZNN] ceramics were investigated. The 0.665 PZ 0.45 T 0.55 ‐0.335 PZNN ceramic has the triple point composition, where the rhombohedral, pseudocubic, and tetragonal structures coexist. Maximum d 33 and k p values of 770 pC/N and 0.69, respectively, were observed from this specimen; it also exhibited a large ε T 33 / ε o value of 3250. Although the maximum d 33 value was obtained from the triple point composition specimen, its g 33 and d 33 × g 33 values were relatively small because of its large ε T 33 / ε o value. However, the 0.665 PZ 0.46 T 0.54 ‐0.335 PZNN ceramic, which has a rhombohedral structure, exhibited a large g 33 value of 43 × 10 −3 Vm/N and a d 33 × g 33 value of 27 000 × 10 −15 m 2 /N. Therefore, this ceramic is a good candidate for multilayer actuators and piezoelectric energy harvesters.
- 13 June 2015
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 98 (9) , 2887-2893
Structural and Piezoelectric Properties of (1− x )Pb(Zr 1− y Ti y )O 3 – x Pb(Zn 0.4 Ni 0.6 ) 1/3 Nb 2/3 O 3 Ceramics Near Triple Point
The crystal structure and piezoelectric properties of (1− x )Pb(Zr 1− y Ti y )O 3 ‐ x Pb(Zn 0.4 Ni 0.6 ) 1/3 Nb 2/3 O 3 [(1− x ) PZ 1− y T y ‐ x PZNN] ceramics were investigated. The 0.665 PZ 0.45 T 0.55 ‐0.335 PZNN ceramic has the triple point composition, where the rhombohedral, pseudocubic, and tetragonal structures coexist. Maximum d 33 and k p values of 770 pC/N and 0.69, respectively, were observed from this specimen; it also exhibited a large ε T 33 / ε o value of 3250. Although the maximum d 33 value was obtained from the triple point composition specimen, its g 33 and d 33 × g 33 values were relatively small because of its large ε T 33 / ε o value. However, the 0.665 PZ 0.46 T 0.54 ‐0.335 PZNN ceramic, which has a rhombohedral structure, exhibited a large g 33 value of 43 × 10 −3 Vm/N and a d 33 × g 33 value of 27 000 × 10 −15 m 2 /N. Therefore, this ceramic is a good candidate for multilayer actuators and piezoelectric energy harvesters.
- 1 December 2014
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 34 (16) , 4193-4200
Influence of sintering conditions on piezoelectric properties of KNbO3 ceramics
- 1 December 2014
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 34 (16) , 4193-4200
Influence of sintering conditions on piezoelectric properties of KNbO3 ceramics