Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Bartosz Pękosławski has a total of 42 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Temperature Variations in a Flexible Thermoelectric Module with an Evaporative Heat Sink

    by Monika Jangas, Anna Dąbrowska, Łukasz Starzak, Bartosz Pękosławski, Agata Kmiecik, Marcin Jachowicz, Szymon Ordysiński

    Exposure to hot microclimate constitutes a serious threat to human health, especially in environments where collective protection measures cannot be implemented. Despite technological advances, personal cooling solutions remain insufficient for long-term use. Thermoelectric modules (TEMs) offer a promising pathway for developing cooling garments. This paper deals with temperature variations in a cooling set composed of a TEM and an evaporative heat sink, for different supply currents. A special methodology was adopted that included the use of a skin model placed in a climatic chamber, and temperature sensors that allowed temperatures at several points to be recorded. After 30 min of operation, the cold side temperature of the TEM was approximately 3 °C to 4.5 °C lower than when the heat sink was absent and the TEM was not supplied. This is close to what thermal comfort requires and may become too small for longer operation or less favourable climatic conditions. Enhanced heat dissipation from the hot side is therefore essential for enabling TEMs to function effectively in wearable colling systems, which makes research on heat sinks other than evaporative ones necessary.

  • Open Access

    Functionality Evaluation of System for Monitoring and Prevention of Thermal Load in Glassworks

    by Anna Dąbrowska, Monika Jangas, Magdalena Młynarczyk, Łukasz Starzak, Bartosz Pękosławski, Agata Kmiecik, Marcin Jachowicz

    A hot microclimate is one of the hazards that glassworkers may be exposed to. In particular, high ambient temperatures contribute to thermal load. New measures are needed to monitor this parameter in the work environment and to protect workers from related health issues. Within this research study, a new system for monitoring and prevention of thermal load in glassworks is outlined, in alignment with the Industry 5.0 vision, which is focused on humans. It consists of a monitoring part that evaluates thermal load, an actuator part that provides workers with individual cooling through electronically controlled thermoelectric modules, and a communication part for wireless communication between the monitoring and actuator parts. The functionality of the system was evaluated in a controlled environment using a microclimate chamber, a thermal manikin, and a professional wet bulb and globe temperature meter. The tests performed have proven that the system properly reacts to a potential high thermal load by activating the cooling function in the dedicated clothing with integrated thermoelectric modules. The heat flux density from the relevant thermal manikin segment reaches a maximum of 44 W/m2.

  • Open Access

    A Performance Evaluation of Flexible Thermoelectric Modules for Application in a Cooling Garment

    by Anna Dąbrowska, Monika Kobus, Łukasz Starzak, Bartosz Pękosławski, Paulina Łataś

    In recent years, significant progress in thermoelectric module (TEM) technology has been achieved in terms of both flexibility and efficiency. This has created great application potential for it, including in cooling garments. In this paper, the results from performance tests of six selected flexible TEMs are presented and discussed in terms of their applicability in a cooling garment. For this purpose, a special testing methodology was adopted that included the use of a skin model located in a microclimate chamber that allowed the analysis of the absorbed heat flow rate from the cold side of a TEM. In addition, electrical parameters were measured in order to calculate the coefficient of performance for each of the evaluated TEMs. Based on these measurements, the TEMs were compared in terms of the cold-side heat flow rate and the number of modules needed to achieve a given heat flow rate or total cooling surface area. The best results were achieved for the TEM with dimensions of 85 mm × 68 mm × 6 mm, for which a maximum heat flow rate of 1.39 W was achieved with an electrical supply power of 0.35 W. To achieve similar values with other evaluated TEMs, two to five modules would have to be applied.


  • Open Access

    Self-noise reduction in a FOG-based rotational seismometer confirmed by Allan variance analysis

    by Rafał Kiełbik, Piotr Zając, Piotr Amrozik, Cezary Maj, Michał Szermer, Łukasz Starzak, Bartosz Pękosławski, Grzegorz Jabłoński, Wojciech Tylman, Anna T. Kurzych, et al.

    Reducing noise in fibre-optic gyroscope (FOG)-based rotational seismometers is crucial in guaranteeing their applicability as future high-precision sensors. This paper presents a practical approach to noise analysis of a designed and manufactured FOG-based three-axis rotational seismometer. The performed measurements show that proper identification of noise sources and subsequent changes to the device’s configuration which addressed these noise issues, visibly improved the Allan deviation plot of the device. In particular, angle random walk was reduced from 100–200 to around 35 nrad/s/√Hz and bias instability – from several dozens down to single nrad/s. These improvements were achieved only by elimination or mitigation of the impact of all noise sources, without changing any optoelectronic components of the constructed device and without applying any additional post-processing methods.


  • Open Access

    Integration of Active Clothing with a Personal Cooling System within the NGIoT Architecture for the Improved Comfort of Construction Workers

    by Anna Dąbrowska, Monika Kobus, Piotr Sowiński, Łukasz Starzak, Bartosz Pękosławski

    Intense physical activity and high ambient temperature cause construction workers to be exposed to an increased risk of overheating, especially in the summer season. Personal cooling systems have great potential to support workers’ thermoregulation and reduce this risk. In particular, solutions based on the thermoelectric effect can provide high cooling effectiveness and ergonomics at the same time. In this paper, a newly developed active clothing solution with flexible thermoelectric modules intended for outdoor activities is presented. The active clothing was subjected to utility tests on a treadmill under laboratory conditions with the participation of potential end users. A comparison of results from cooled and uncooled places indicated a reduction in local skin temperature of as much as 2.7 °C. Moreover, a gradual decrease in temperature in the uncooled place during the experiment was observed. Based on the positive results from this evaluation, the personal cooling system was integrated into active clothing within the ASSIST-IoT NGIoT reference architecture. This allows contextual and personalized adjustment of the cooling power to be provided using AI techniques and, additionally, by using data from a weather station and a smartwatch. Training procedures and models for the AI system are proposed, with special attention paid to the privacy aspect.


  • Open Access

    Evaluation of Performance and Power Consumption of a Thermoelectric Module-Based Personal Cooling System—A Case Study

    by Anna Dąbrowska, Monika Kobus, Łukasz Starzak, Bartosz Pękosławski

    Thermoelectric (TE) technology is promising for reducing thermal discomfort of workers during their routine professional activities. In this manuscript, a preliminary evaluation of a newly developed personal cooling system (PCS) with flexible TE modules is presented based on an analysis of cooling efficiency and power consumption. For this purpose, tests with human participation were performed involving the monitoring of local skin temperature changes and electrical parameters of the controller. Thanks to TE cooling, a significant reduction of local skin temperature was observed at the beginning of the experiment, reaching as much as 6 °C. However, the observed effect systematically became weaker with time, with the temperature difference decreasing to about 3 °C. Cooling efficiency stayed at the same level over the ambient temperature range from 25 °C to 35 °C. The obtained results showed that a proper fitting of the PCS to the human body is a crucial factor influencing the PCS cooling efficiency.


  • Open Access

    Evaluation of Heating Inserts in Active Protective Clothing for Mountain Rescuers—Preliminary Tests

    by Sylwia Krzemińska, Agnieszka Greszta, Grażyna Bartkowiak, Anna Dąbrowska, Rafał Kotas, Bartosz Pękosławski, Bartosz Małachowski, Pamela Miśkiewicz

    Rescue operations in mountain areas, lasting many hours, pose a mental and physical burden on the rescuer’s body. In addition, they cause thermal discomfort associated with variable energy expenditures and the high variability of weather conditions. One of the solutions for improving the comfort of the work of mountain rescuers is clothing with an active heating function. This paper discusses the technology of manufacturing flexible heating inserts with steel thread as a heating element. In order to assess the durability and safety of the applied heating inserts, they were subjected to simulated conditions of use. Multiple washing (25 cycles) and bending (9000 cycles) as well as exposure to artificial acidic sweat did not cause a significant change in the electrical power and resistance of the heating inserts. In order to assess the effectiveness of the inserts, they were tested within a system of clothing fabrics on an “artificial skin model”. Supplying the heating insert with a voltage of 4 V increased the thermal resistance of the fabric system, incorporating the insert by approx. 40%. Due to their high flexibility, durability, and heating efficiency, the developed heating inserts are a major step towards the development of electrical heated clothing.


  • Open Access

    Power Supply and Control Unit for Actively Heated Protective Clothing with Photovoltaic Energy Harvesting

    by Bartosz Pękosławski, Paweł Marciniak, Łukasz Starzak, Adam Stawiński, Grażyna Bartkowiak

    An active heating system has been developed for application in smart clothing for mountain rescuers. It uses a set of sensors and is aimed at gathering necessary data for the elaboration and testing of an automatic control algorithm. The system is powered by a lithium-ion battery pack, which can be additionally charged from flexible PV modules. The article presents an estimation of this system’s power supply requirements and its energy budget. Since the system’s maximum operation time strongly depends on the efficiency of its main power converter, the design of the latter was based on a model enabling power loss estimation in its particular components. Characteristics ultimately measured on a prototype showed a high agreement with simulations. Furthermore, five different arrangements of PV modules were studied in order to find the most effective one. The system was tested in real conditions for the three most promising PV module configurations.


  • Open Access

    Analysis of Efficiency of Thermoelectric Personal Cooling System Based on Utility Tests

    by Anna Dąbrowska, Monika Kobus, Łukasz Starzak, Bartosz Pękosławski

    Thermoelectric modules can find practical application in clothing with a cooling function. A personal cooling system using Peltier modules integrated with clothing was developed and tested with the participation of a person. A dedicated electronic controller was designed that enabled the power or temperature to be controlled and recorded. In the research, the influence of heat sinks and the method of controlling the operation of the module on the cooling efficiency was assessed. The research was aimed at selecting the operating mode of the controller and choosing the arrangement of modules comparing cooling efficiency. The research showed that by selection of appropriate controlling mode, the electric power used can be reduced while keeping the cooling efficiency at the same level. The location of Peltier modules in places where they can tightly adhere to the body increases their performance.


  • Open Access

    A Comparative Analysis of Thermoelectric Modules for the Purpose of Ensuring Thermal Comfort in Protective Clothing

    by Anna Dąbrowska, Monika Kobus, Bartosz Pękosławski, Łukasz Starzak

    In recent times, more and more workers are exposed to thermal stress due to climate changes and increased ambient temperature. Demanding physical activities and the use of protective clothing are additional sources of thermal load for workers. Therefore, recent research has focused on the development of protective clothing with a cooling function. Phase change materials, air or liquid, were mainly used for this purpose; only a few publications were concerned the use of thermoelectric modules. This publication analyzes the influence of such factors as supplied current, ambient temperature, and the type of heat sink on the amount of heat flux transferred by a thermoelectric cooler (TEC) and the electric power consumed by it. In the course of laboratory tests, a flexible thermoelectric module and three heat sink variants were tested. For this purpose, a polymer TEGway heat sink, a metal one, and a self-made one based on a superabsorbent were used. The research showed that at a temperature of 30 °C and above, the amount of the heat flux transferred by a TEC with a total area of 58 cm2, and an active area of 10 cm2 should be expected to be from 1 W to 1.5 W. An increase in ambient temperature from 20 to 35 °C caused a significant reduction in the heat flux by about 1 W. The results obtained indicated that the type of heat sink affects the heat flux drawn by the TEC to a statistically significant extent. The heat sink using the evaporation effect turned out to be the most efficient.