Dmytro Tsyplenkov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Dmytro Tsyplenkov has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Mykhailo Kovalenko
National Technical University of Ukraine "Igor Sikorsky Kyiv Polytechnic Institute
4 shared publications - Iryna Kovalenko
Національний технічний університет України «Київський політехнічний інститут імені Ігоря Сікорського», м. Київ
3 shared publications - Maryna Kyrychenko
Department of Electric Power Engineering, Dnipro University of Technology, 19 Yavornytskoho Ave., 49005 Dnipro, Ukraine
2 shared publications - Vitaliy Kuznetsov
Ukrainian State University of Science and Technologies
2 shared publications - Андрій Гребенюк
Дніпровський фаховий коледж енергетичних та інформаційних технологій
2 shared publications A. M. Grebeniuk
Державний вищий навчальний заклад «Національний гірничий університет
1 shared publication
Latest Publications
- 27 August 2026
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 4,p. 89-97
Comparison of impulse processes in spatially shifted ring-like cores made of ferrite and thin sheet steel
Purpose. Development of a numerical simulation model of pulse processes of magnetic cores made of ferrite and thin-sheet electrical steel in order to estimate the magnitude of pulse overvoltages. Methodology. The distribution of the electromagnetic field and eddy currents was calculated using the finite element method. Computer-aided design tools were used to develop geometric models of the computational domain of the studied processes in ring-shaped cores. The theory of transient processes and the laws of electric circuits were used to excite pulse processes in the studied system. Findings. A three-dimensional numerical ring-field mathematical model of pulse excitation of ring-shaped cores made of different materials of electrical steel of the sensor and inductor was developed, which is used to diagnose interturn short circuits of the filled windings. The model allows determining the time dependences of current, voltage and the nature of the change in magnetic flux during the passage of the pulse excitation front. The distributions of the electromagnetic field, eddy currents and the dynamics of their attenuation were obtained for different values of the magnetic permeability and electrical conductivity of the materials. The obtained results allow us to quantitatively assess the influence of material parameters on pulse processes, to determine the limits of efficiency of using ferrite and cores from different types of electrical steel in high-frequency diagnostic systems, sensors and energy converters. Originality. The results of the analysis of numerical simulation modeling of the studied system showed that, depending on the type of core material, wave penetration processes with minimal losses are inherent in ferrite material. In thin-sheet steel, eddy currents in each individual sheet have a significant effect on pulse shielding, which significantly affects the output signal. Practical value. The obtained results can be used to build systems for diagnosing interturn insulation of windings of electrical machines, in particular, as a methodological basis for diagnostic devices based on the use of the proposed approach.
- 27 August 2026
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 4,p. 89-97
Comparison of impulse processes in spatially shifted ring-like cores made of ferrite and thin sheet steel
Purpose. Development of a numerical simulation model of pulse processes of magnetic cores made of ferrite and thin-sheet electrical steel in order to estimate the magnitude of pulse overvoltages. Methodology. The distribution of the electromagnetic field and eddy currents was calculated using the finite element method. Computer-aided design tools were used to develop geometric models of the computational domain of the studied processes in ring-shaped cores. The theory of transient processes and the laws of electric circuits were used to excite pulse processes in the studied system. Findings. A three-dimensional numerical ring-field mathematical model of pulse excitation of ring-shaped cores made of different materials of electrical steel of the sensor and inductor was developed, which is used to diagnose interturn short circuits of the filled windings. The model allows determining the time dependences of current, voltage and the nature of the change in magnetic flux during the passage of the pulse excitation front. The distributions of the electromagnetic field, eddy currents and the dynamics of their attenuation were obtained for different values of the magnetic permeability and electrical conductivity of the materials. The obtained results allow us to quantitatively assess the influence of material parameters on pulse processes, to determine the limits of efficiency of using ferrite and cores from different types of electrical steel in high-frequency diagnostic systems, sensors and energy converters. Originality. The results of the analysis of numerical simulation modeling of the studied system showed that, depending on the type of core material, wave penetration processes with minimal losses are inherent in ferrite material. In thin-sheet steel, eddy currents in each individual sheet have a significant effect on pulse shielding, which significantly affects the output signal. Practical value. The obtained results can be used to build systems for diagnosing interturn insulation of windings of electrical machines, in particular, as a methodological basis for diagnostic devices based on the use of the proposed approach.
- 26 December 2025
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 6,p. 69-78
Model-based designof a cone crusher adaptive control system
Purpose. The purpose of the article is to develop a methodology for creating cone crusher adaptive control system based on the model-based design method for automated software generation of microprocessor controllers. Methodology. A method based on a block-oriented predictive model was used to generate control signals for the cone crusher. The parameters and structure of this model were identified in real time using measured data from the plant. A prototype of the control system was created in MATLAB/Simulink. Then, the model-based design method was used to generate software for digital signal processors. Mathematical statistics methods were employed to analyze the experimental results. Findings. A method of model-based design of an adaptive control system for a cone crusher has been developed. This system uses a predictive model of a block-oriented structure. This model adjusts the predictive controller’s structure and parameters directly during operation. This approach makes it possible to divide the functions of identifying the process model and generating controls between the two digital controllers. Consequently, the average computational time is reduced while ensuring the stabilization of the degree of homogeneity of ore crushing and separate output of the control size class, with respective standard deviation coefficients not exceeding 3.42 and 1.83 %, respectively. Originality. The regularity of the effect of the closed-side setting and the eccentric speed on the particle size distribution of crushed ore has been established. This shows that high homogeneity of the crushed product is ensured by simultaneously adjusting these input coordinates. We propose a new method for synthesizing an adaptive cone crusher control system based on a model-based design approach. This method provides automated real-time generation of software for microprocessor-based controllers, allowing the system to quickly adjust to changes in rock mass characteristics and other disturbances. Practical value. A hardware and software implementation of an adaptive control system for a cone crusher is proposed. This system is based on a block-oriented predictive model. The model ensures the stabilization of the required ore particle size distribution. This stabilization is achieved by adjusting the closed-side setting and the eccentric speed. The system is based on 16-bit, low-cost digital signal processors. A prototype of the system was tested in a crushing plant at a metallurgical enterprise.
- 26 December 2025
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 6,p. 69-78
Model-based designof a cone crusher adaptive control system
Purpose. The purpose of the article is to develop a methodology for creating cone crusher adaptive control system based on the model-based design method for automated software generation of microprocessor controllers. Methodology. A method based on a block-oriented predictive model was used to generate control signals for the cone crusher. The parameters and structure of this model were identified in real time using measured data from the plant. A prototype of the control system was created in MATLAB/Simulink. Then, the model-based design method was used to generate software for digital signal processors. Mathematical statistics methods were employed to analyze the experimental results. Findings. A method of model-based design of an adaptive control system for a cone crusher has been developed. This system uses a predictive model of a block-oriented structure. This model adjusts the predictive controller’s structure and parameters directly during operation. This approach makes it possible to divide the functions of identifying the process model and generating controls between the two digital controllers. Consequently, the average computational time is reduced while ensuring the stabilization of the degree of homogeneity of ore crushing and separate output of the control size class, with respective standard deviation coefficients not exceeding 3.42 and 1.83 %, respectively. Originality. The regularity of the effect of the closed-side setting and the eccentric speed on the particle size distribution of crushed ore has been established. This shows that high homogeneity of the crushed product is ensured by simultaneously adjusting these input coordinates. We propose a new method for synthesizing an adaptive cone crusher control system based on a model-based design approach. This method provides automated real-time generation of software for microprocessor-based controllers, allowing the system to quickly adjust to changes in rock mass characteristics and other disturbances. Practical value. A hardware and software implementation of an adaptive control system for a cone crusher is proposed. This system is based on a block-oriented predictive model. The model ensures the stabilization of the required ore particle size distribution. This stabilization is achieved by adjusting the closed-side setting and the eccentric speed. The system is based on 16-bit, low-cost digital signal processors. A prototype of the system was tested in a crushing plant at a metallurgical enterprise.
- 30 August 2025
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 4,p. 108-116
Mathematical simulation of brushless high-speed permanent magnet motor
Purpose. To develop a numerical two-dimensional field mathematical model of a brushless high-speed permanent magnet motor to estimate its parameters, characteristics and determine the magnitude of losses in the magnetic core under different control methods. Methodology. The finite element method was used to calculate the electromagnetic field distribution in the computational domain of the motor under study. To develop two-dimensional and three-dimensional drawings of the design area, methods and tools of computer-aided design were used. Numerical methods for calculating losses in the magnetic core developed by Giovanni Bertotti were used to calculate losses in the magnetic core. The Fourier series expansion method and spectral analysis methods were used to model various motor control methods. Findings. A two-dimensional numerical circular-field mathematical model of a brushless high-speed motor with permanent magnets has been developed. The model was developed to estimate the distribution of the electromagnetic field and eddy currents in the structural and active elements of the motor in question in order to determine the magnitude of losses under different power supply methods. The paper investigates the dependence of losses in individual structural elements of the motor under study when powered by a sinusoidal voltage source and when powered by a PWM inverter. Replacing permanent magnets with rectangular magnets reduces the cost of motor manufacturing. The use of rectangular permanent magnets reduces losses in the computational domain, the magnitude of electromagnetic torque fluctuations, but reduces the magnitude of traction. Originality. Using the developed numerical circular-field mathematical model, it is proved that losses in the magnetic core of a high-speed motor and its structural elements significantly depend on the control method and configuration of the magnetic system and the motor as a whole. The study allows solving urgent scientific and practical problems related to the optimization of the structure depending on the optimization criteria: reduction of heating or losses, reduction of vibration and noise, etc. Practical value. The modelling results indicate the prospects for the industrial implementation of high-speed permanent magnet motors as part of various complexes and systems: vehicles, hand-held power tools, aircraft, unmanned devices and systems, etc.
- 30 August 2025
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 4,p. 108-116
Mathematical simulation of brushless high-speed permanent magnet motor
Purpose. To develop a numerical two-dimensional field mathematical model of a brushless high-speed permanent magnet motor to estimate its parameters, characteristics and determine the magnitude of losses in the magnetic core under different control methods. Methodology. The finite element method was used to calculate the electromagnetic field distribution in the computational domain of the motor under study. To develop two-dimensional and three-dimensional drawings of the design area, methods and tools of computer-aided design were used. Numerical methods for calculating losses in the magnetic core developed by Giovanni Bertotti were used to calculate losses in the magnetic core. The Fourier series expansion method and spectral analysis methods were used to model various motor control methods. Findings. A two-dimensional numerical circular-field mathematical model of a brushless high-speed motor with permanent magnets has been developed. The model was developed to estimate the distribution of the electromagnetic field and eddy currents in the structural and active elements of the motor in question in order to determine the magnitude of losses under different power supply methods. The paper investigates the dependence of losses in individual structural elements of the motor under study when powered by a sinusoidal voltage source and when powered by a PWM inverter. Replacing permanent magnets with rectangular magnets reduces the cost of motor manufacturing. The use of rectangular permanent magnets reduces losses in the computational domain, the magnitude of electromagnetic torque fluctuations, but reduces the magnitude of traction. Originality. Using the developed numerical circular-field mathematical model, it is proved that losses in the magnetic core of a high-speed motor and its structural elements significantly depend on the control method and configuration of the magnetic system and the motor as a whole. The study allows solving urgent scientific and practical problems related to the optimization of the structure depending on the optimization criteria: reduction of heating or losses, reduction of vibration and noise, etc. Practical value. The modelling results indicate the prospects for the industrial implementation of high-speed permanent magnet motors as part of various complexes and systems: vehicles, hand-held power tools, aircraft, unmanned devices and systems, etc.
- 30 April 2024
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 2,p. 88-95
Mathematical modeling of a magnetic gear for an autonomous wind turbine
New+Electrical Complexes and Systems +https://doi.org/10.33271/nvngu/2024-2 +/jdownloads/pdf/2024/2/02_2024_Contents-en-GB.pdf
- 30 April 2024
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 2,p. 88-95
Mathematical modeling of a magnetic gear for an autonomous wind turbine
New+Electrical Complexes and Systems +https://doi.org/10.33271/nvngu/2024-2 +/jdownloads/pdf/2024/2/02_2024_Contents-en-GB.pdf
- 30 October 2022
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 5,p. 74-79
Mathematical simulation of autonomous wind electric installation with magnetoelectric generator
Purpose. Development of a mathematical model of an autonomous wind power plant based on an end-generator with a double stator and combined excitation to evaluate methods for improving the efficiency of conversion of mechanical wind energy into electricity. Methodology. The research used methods of general theory of wind power plants, methods of mathematical modeling, which are based on the numerical solution of nonlinear differential equations to evaluate methods for correcting the output power in Matlab-Simulink by modifying standard units. Findings. A numerical simulation mathematical model of an autonomous wind power plant consisting of a magnetoelectric generator with an axial magnetic flux with combined excitation and a double stator has been developed. The model was created to study the parameters and characteristics of the installation, as well as to evaluate methods and means to improve the efficiency of conversion of wind energy into electricity. According to the research, it is established that a more effective method for regulating the output power of the generator in the wind turbine is the use of additional winding for magnetization, compared with the use of additional capacity. The latter provides up to 716% increase in output power, while using the magnetizing winding can increase the output power to 3235%. The results obtained by the authors allow further developing a number of methods to increase the efficiency of conversion of mechanical energy of the wind turbine rotor into electrical energy. Originality. The mathematical model developed for the first time, in contrast to the existing ones, takes into account the presence of a double stator, an additional winding for magnetization of the magnetic system and the axial nature of the circuit of the main and additional magnetic flux. The developed model also takes into account the change in the parameters of the electric generator with axial magnetic flux when changing the parameters of the wind, the rotor of the wind turbine and the load. The model is designed to analyze the possibility of adjusting the output power of the generator when the wind speed changes. Practical value. The simulation results indicate the prospects of industrial implementation of wind power plant based on magnetoelectric generator for their use as autonomous electrical installations and as part of shunting power systems.
- 30 October 2022
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 5,p. 74-79
Mathematical simulation of autonomous wind electric installation with magnetoelectric generator
Purpose. Development of a mathematical model of an autonomous wind power plant based on an end-generator with a double stator and combined excitation to evaluate methods for improving the efficiency of conversion of mechanical wind energy into electricity. Methodology. The research used methods of general theory of wind power plants, methods of mathematical modeling, which are based on the numerical solution of nonlinear differential equations to evaluate methods for correcting the output power in Matlab-Simulink by modifying standard units. Findings. A numerical simulation mathematical model of an autonomous wind power plant consisting of a magnetoelectric generator with an axial magnetic flux with combined excitation and a double stator has been developed. The model was created to study the parameters and characteristics of the installation, as well as to evaluate methods and means to improve the efficiency of conversion of wind energy into electricity. According to the research, it is established that a more effective method for regulating the output power of the generator in the wind turbine is the use of additional winding for magnetization, compared with the use of additional capacity. The latter provides up to 716% increase in output power, while using the magnetizing winding can increase the output power to 3235%. The results obtained by the authors allow further developing a number of methods to increase the efficiency of conversion of mechanical energy of the wind turbine rotor into electrical energy. Originality. The mathematical model developed for the first time, in contrast to the existing ones, takes into account the presence of a double stator, an additional winding for magnetization of the magnetic system and the axial nature of the circuit of the main and additional magnetic flux. The developed model also takes into account the change in the parameters of the electric generator with axial magnetic flux when changing the parameters of the wind, the rotor of the wind turbine and the load. The model is designed to analyze the possibility of adjusting the output power of the generator when the wind speed changes. Practical value. The simulation results indicate the prospects of industrial implementation of wind power plant based on magnetoelectric generator for their use as autonomous electrical installations and as part of shunting power systems.
- Open Access
- 8 September 2021
- Published by RS Global Sp. z O.O.
ELECTROTECHNICAL MATERIALS
The regularities of processes and phenomena that occur in dielectric, conductive, semiconductor and magnetic materials as part of electrical and electronic devices under the influence of energy of electric, magnetic and thermal fields are considered. The main feature of the textbook is a detailed structuring of educational material, focusing largely on the distance form of learning, as well as demonstration of the close relationship of the properties of various electrical materials and the basics of electrical engineering on specific examples. The manual is intended for students of specialties: 141 - "Electrical Energetics, Electrical Engineering and Electromechanics" and 275 - "Transport technologies", as well as for students of other specialties of higher education, which are related to the study of disciplines of electrical engineering and electronic computer science.
- 8 September 2021
- Published by RS Global Sp. z O.O.
Open AccessELECTROTECHNICAL MATERIALS
The regularities of processes and phenomena that occur in dielectric, conductive, semiconductor and magnetic materials as part of electrical and electronic devices under the influence of energy of electric, magnetic and thermal fields are considered. The main feature of the textbook is a detailed structuring of educational material, focusing largely on the distance form of learning, as well as demonstration of the close relationship of the properties of various electrical materials and the basics of electrical engineering on specific examples. The manual is intended for students of specialties: 141 - "Electrical Energetics, Electrical Engineering and Electromechanics" and 275 - "Transport technologies", as well as for students of other specialties of higher education, which are related to the study of disciplines of electrical engineering and electronic computer science.
- 12 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Optimum parameters of electromechanical system model “electrical grid-drive-compressor-pneumatic network”
Increasing the energy efficiency of the system “electrical network - compressor - pneumatic network” in general can be achieved by performing a “floating” upper level of pressure. The optimal parameters of the mathematical model that allow to determine the optimum operating mode of the compressed air production and distribution system consisting of the following elements “electric network - drive - compressor - pneumatic network” are substantiated in the work. The intervals of the pump pumping-down cycle in the pneumonetwork are determined at a fixed value of compressed air consumption, and the dependence of the optimum efficiency on the compressed air consumption consumed by the compressed air receivers is determined.
- 12 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Optimum parameters of electromechanical system model “electrical grid-drive-compressor-pneumatic network”
Increasing the energy efficiency of the system “electrical network - compressor - pneumatic network” in general can be achieved by performing a “floating” upper level of pressure. The optimal parameters of the mathematical model that allow to determine the optimum operating mode of the compressed air production and distribution system consisting of the following elements “electric network - drive - compressor - pneumatic network” are substantiated in the work. The intervals of the pump pumping-down cycle in the pneumonetwork are determined at a fixed value of compressed air consumption, and the dependence of the optimum efficiency on the compressed air consumption consumed by the compressed air receivers is determined.
- 1 April 2019
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 2,p. 101-107
Justification of the optimum operation of electromechanical system for production and distribution of pressurized air
Justification of the optimum operation of electromechanical system for production and distribution of pressurized air
- 1 April 2019
- Published by Dnipro University of Technology in Naukovyi Visnyk Natsionalnoho Hirnychoho Universytetu
- No. 2,p. 101-107
Justification of the optimum operation of electromechanical system for production and distribution of pressurized air
Justification of the optimum operation of electromechanical system for production and distribution of pressurized air
- Open Access
- 12 March 2016
- Published by National Technical University Kharkiv Polytechnic Institute in Electrical Engineering & Electromechanics
- No. 1,p. 33-37
MACHINE-TRANSFORMER UNITS FOR WIND TURBINES
МАШИННО-ТРАНСФОРМАТОРНИЙ АГРЕГАТ ДЛЯ ВІТРОЕНЕРГЕТИЧНИХ УСТАНОВОК
- 12 March 2016
- Published by National Technical University Kharkiv Polytechnic Institute in Electrical Engineering & Electromechanics
- No. 1,p. 33-37
Open AccessMACHINE-TRANSFORMER UNITS FOR WIND TURBINES
МАШИННО-ТРАНСФОРМАТОРНИЙ АГРЕГАТ ДЛЯ ВІТРОЕНЕРГЕТИЧНИХ УСТАНОВОК