Benjapon Chalermsinsuwan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Benjapon Chalermsinsuwan has a total of 106 co-authors. Here are the top co-authors by number of shared publications:
- Pornpote Piumsomboon
Chulalongkorn University
19 shared publications Pornpote Piumsomboon
13 shared publicationsPrathana Nimmanterdwong
7 shared publicationsRatchanon Piemjaiswang
7 shared publications- Ratchanon Piemjaiswang
Environmental Research Institute, Chulalongkorn University, Bangkok, 10330, Thailand
7 shared publications Chaiwat Soanuch
Department of Chemical Technology, Faculty of Science, Chulalongkorn University, 254 Phyathai Road, Wangmai, Pathumwan, Bangkok 10330, Thailand
6 shared publications
Latest Publications
- Open Access
- 23 October 2026
- Published by Elsevier in Results in Engineering
- Vol. 32
Statistical evaluation of CO2 adsorption performance of Covalent organic frameworks (COFs) using artificial neural network modeling
- 23 October 2026
- Published by Elsevier in Results in Engineering
- Vol. 32
Open AccessStatistical evaluation of CO2 adsorption performance of Covalent organic frameworks (COFs) using artificial neural network modeling
- Open Access
- 29 September 2026
- Published by Elsevier in Results in Engineering
- Vol. 32
Unsupervised classification of industrial boiler operation signals using dynamic time warping self-organizing map (DTW-SOM) and long short-term memory (LSTM) framework
- 29 September 2026
- Published by Elsevier in Results in Engineering
- Vol. 32
Open AccessUnsupervised classification of industrial boiler operation signals using dynamic time warping self-organizing map (DTW-SOM) and long short-term memory (LSTM) framework
- 25 July 2026
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 14 (5)
Effect of wire configuration on collection efficiency of an electrostatic precipitator using EHD simulation
- 25 July 2026
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 14 (5)
Effect of wire configuration on collection efficiency of an electrostatic precipitator using EHD simulation
- Open Access
- 27 June 2026
- Published by Elsevier in Results in Engineering
- Vol. 32
Impact of operating conditions on performance and environmental aspects in large scale co-firing fluidized bed boilers: A CFD approach
- 27 June 2026
- Published by Elsevier in Results in Engineering
- Vol. 32
Open AccessImpact of operating conditions on performance and environmental aspects in large scale co-firing fluidized bed boilers: A CFD approach
- Open Access
- 10 June 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (24) , 35750-35761
A Study of CO 2 Adsorption of MEA-Modified Zeolite 13X and K 2 CO 3 -Impregnated Alumina for Direct Air Capture
Rising industrial CO2 emissions have created an urgent need for efficient carbon capture and storage (CCS) technologies. This study compares the CO2 adsorption performance of three sorbents, namely zeolite 13X (Z13), monoethanolamine-modified zeolite (Z13/MEA), and K2CO3-impregnated alumina (K2CO3/Al2O3), under realistic direct air capture (DAC) conditions (∼450 ppm of CO2, RH 60–65%, 26 ± 2 °C). The sorbents were prepared by wet impregnation with actual loadings of 6.98 wt % MEA (CHNS) and 4.01 wt % K2CO3 (XRF), and were characterized by BET, CHNS, XRF, SEM, XRD, FTIR, and TGA. Z13/MEA exhibited the highest uptake (∼40 mgCO2/g), substantially greater than pristine Z13 (12 mg/g) and K2CO3/Al2O3 (5 mg/g). Under the humid DAC pathway (1:1 bicarbonate stoichiometry), these values correspond to 79% amine and 39% carbonate utilization, respectively. The superior performance of Z13/MEA is attributed to chemisorption at the −NH2 sites, confirmed by FTIR bands at 1650 cm–1 (carbamate) and 1380 cm–1 (bicarbonate) and an increase in carbon content from 3.4% to 3.8% after use. Pore blocking by MEA reduced the specific surface area from 502 to 25 m2/g but partially recovered to 262 m2/g after regeneration. XRD results confirmed the zeolite framework remained intact. Z13/MEA retained ≥90% of its initial capacity over 10 cycles under mild TSA regeneration at 80 °C, indicating good cyclic stability and low regeneration-energy demand. These findings provide a comparative basis for designing durable sorbents for CCS technology toward Net-Zero goals.
- 10 June 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (24) , 35750-35761
Open AccessA Study of CO 2 Adsorption of MEA-Modified Zeolite 13X and K 2 CO 3 -Impregnated Alumina for Direct Air Capture
Rising industrial CO2 emissions have created an urgent need for efficient carbon capture and storage (CCS) technologies. This study compares the CO2 adsorption performance of three sorbents, namely zeolite 13X (Z13), monoethanolamine-modified zeolite (Z13/MEA), and K2CO3-impregnated alumina (K2CO3/Al2O3), under realistic direct air capture (DAC) conditions (∼450 ppm of CO2, RH 60–65%, 26 ± 2 °C). The sorbents were prepared by wet impregnation with actual loadings of 6.98 wt % MEA (CHNS) and 4.01 wt % K2CO3 (XRF), and were characterized by BET, CHNS, XRF, SEM, XRD, FTIR, and TGA. Z13/MEA exhibited the highest uptake (∼40 mgCO2/g), substantially greater than pristine Z13 (12 mg/g) and K2CO3/Al2O3 (5 mg/g). Under the humid DAC pathway (1:1 bicarbonate stoichiometry), these values correspond to 79% amine and 39% carbonate utilization, respectively. The superior performance of Z13/MEA is attributed to chemisorption at the −NH2 sites, confirmed by FTIR bands at 1650 cm–1 (carbamate) and 1380 cm–1 (bicarbonate) and an increase in carbon content from 3.4% to 3.8% after use. Pore blocking by MEA reduced the specific surface area from 502 to 25 m2/g but partially recovered to 262 m2/g after regeneration. XRD results confirmed the zeolite framework remained intact. Z13/MEA retained ≥90% of its initial capacity over 10 cycles under mild TSA regeneration at 80 °C, indicating good cyclic stability and low regeneration-energy demand. These findings provide a comparative basis for designing durable sorbents for CCS technology toward Net-Zero goals.
- Open Access
- 2 June 2026
- Published by Elsevier in Results in Engineering
- Vol. 31
Pyrolysis upcycling of sugarcane filter cake into engineered biochar for low-carbon cement composites: Process optimization via RSM
- 2 June 2026
- Published by Elsevier in Results in Engineering
- Vol. 31
Open AccessPyrolysis upcycling of sugarcane filter cake into engineered biochar for low-carbon cement composites: Process optimization via RSM
- 26 May 2025
- Published by Springer Nature
- p. 88-96
Computational Fluid Dynamics of Microplastics Separation in Hydrocyclones: Effects of Operating Parameters
- 26 May 2025
- Published by Springer Nature
- p. 88-96
Computational Fluid Dynamics of Microplastics Separation in Hydrocyclones: Effects of Operating Parameters
- Open Access
- 26 May 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-17
Investigation of microwave-assisted regeneration of zeolite 13X for efficient direct air CO2 capture: a comparison with conventional heating method
This study investigates the regeneration of zeolite 13X for direct air CO2 capture by comparing microwave-assisted and conventional heating methods in a fixed-bed reactor. Zeolite 13X, a high-surface-area solid adsorbent, was tested over three adsorption/desorption cycles under ambient conditions with approximately 400 ppm of CO2. Microwave-assisted regeneration, optimized at 300 W for 10 min (350 °C), achieved a regeneration efficiency of 95.26%, with minimal loss in adsorption capacity (9%) across cycles. Conventional heating at 350 °C for 30 min achieved a comparable efficiency of 93.90% but required significantly more time and energy. The microwave technique operates via direct dielectric heating, selectively exciting polar species such as mobile Na⁺ ions within the zeolite framework. This localized and volumetric heating enhances CO2 desorption without requiring reactor preheating or carrier gas flow, unlike conventional methods that rely on slower conduction and convection. As a result, microwave regeneration demonstrated a tenfold reduction in energy consumption (0.06 kWh vs. 0.62 kWh for conventional heating). Statistical analysis using ANOVA identified microwave power and regeneration time as key factors, with microwave power exerting the greatest influence. The study highlights the advantages of microwave-assisted regeneration, including reduced energy demand, shorter regeneration times, and enhanced scalability. These findings emphasize its potential as a transformative approach for advancing direct air capture technologies. Compared to conventional methods, microwave-assisted regeneration offers a more energy-efficient and practical solution for CO2 removal from ambient air.
- 26 May 2025
- Published by Springer Nature in Scientific Reports
- Vol. 15 (1) , 1-17
Open AccessInvestigation of microwave-assisted regeneration of zeolite 13X for efficient direct air CO2 capture: a comparison with conventional heating method
This study investigates the regeneration of zeolite 13X for direct air CO2 capture by comparing microwave-assisted and conventional heating methods in a fixed-bed reactor. Zeolite 13X, a high-surface-area solid adsorbent, was tested over three adsorption/desorption cycles under ambient conditions with approximately 400 ppm of CO2. Microwave-assisted regeneration, optimized at 300 W for 10 min (350 °C), achieved a regeneration efficiency of 95.26%, with minimal loss in adsorption capacity (9%) across cycles. Conventional heating at 350 °C for 30 min achieved a comparable efficiency of 93.90% but required significantly more time and energy. The microwave technique operates via direct dielectric heating, selectively exciting polar species such as mobile Na⁺ ions within the zeolite framework. This localized and volumetric heating enhances CO2 desorption without requiring reactor preheating or carrier gas flow, unlike conventional methods that rely on slower conduction and convection. As a result, microwave regeneration demonstrated a tenfold reduction in energy consumption (0.06 kWh vs. 0.62 kWh for conventional heating). Statistical analysis using ANOVA identified microwave power and regeneration time as key factors, with microwave power exerting the greatest influence. The study highlights the advantages of microwave-assisted regeneration, including reduced energy demand, shorter regeneration times, and enhanced scalability. These findings emphasize its potential as a transformative approach for advancing direct air capture technologies. Compared to conventional methods, microwave-assisted regeneration offers a more energy-efficient and practical solution for CO2 removal from ambient air.
- Open Access
- 29 January 2025
- Published by Sustainable Environment Research Institute, Chulalongkorn University in Applied Environmental Research
- Vol. 47 (1)
Enhanced CO2 Capture Performance Using Methyl Diethanolamine-functionalized Silica Gels: Assessing CO2 Capture Capacity
Carbon dioxide (CO2) is a significant greenhouse gas. This causes harm to the environment and to humans. In 2023, atmospheric CO2 levels rose to 420 ppm, marking a new record high. Therefore, technology for capturing CO2 has been developed. At present, a wide variety of technologies have been proposed to capture CO2. Adsorption technology is more affordable and requires less energy for regeneration. There are many potential solid adsorbents for CO2 capture, such as zeolites, alumina, metal‒organic frameworks (MOFs), and mesoporous silicas. Silica materials possess unique properties that make them promising candidates as solid sorbents for CO2 capture. They provide several benefits, such as high adsorption capacity under dry conditions at ambient temperature, along with low energy requirements for regeneration. Amine-functionalized silica adsorbents are among the most promising methods for CO2 capture, offering high efficiency and high uptake rates. In this study, silica gels were grafted and impregnated with amines via methyl diethanolamine (MDEA). The effects of water content and amine loading on CO2 capture performance were investigated. The MDEAs grafted and impregnated on silica gel exhibited excellent CO2 efficiencies of 0.36 and 0.38 mg CO2 per gram sorbent, respectively, which are higher than the 15% efficiency of the unmodified adsorbent. The results showed that the modified silica gel had high CO2 efficiency during the first three adsorption‒regeneration cycles when the water content and amine loading increased. Moreover, the nitrogen content increased with increasing water content, leading to an increase in the adsorption capacity.
- 29 January 2025
- Published by Sustainable Environment Research Institute, Chulalongkorn University in Applied Environmental Research
- Vol. 47 (1)
Open AccessEnhanced CO2 Capture Performance Using Methyl Diethanolamine-functionalized Silica Gels: Assessing CO2 Capture Capacity
Carbon dioxide (CO2) is a significant greenhouse gas. This causes harm to the environment and to humans. In 2023, atmospheric CO2 levels rose to 420 ppm, marking a new record high. Therefore, technology for capturing CO2 has been developed. At present, a wide variety of technologies have been proposed to capture CO2. Adsorption technology is more affordable and requires less energy for regeneration. There are many potential solid adsorbents for CO2 capture, such as zeolites, alumina, metal‒organic frameworks (MOFs), and mesoporous silicas. Silica materials possess unique properties that make them promising candidates as solid sorbents for CO2 capture. They provide several benefits, such as high adsorption capacity under dry conditions at ambient temperature, along with low energy requirements for regeneration. Amine-functionalized silica adsorbents are among the most promising methods for CO2 capture, offering high efficiency and high uptake rates. In this study, silica gels were grafted and impregnated with amines via methyl diethanolamine (MDEA). The effects of water content and amine loading on CO2 capture performance were investigated. The MDEAs grafted and impregnated on silica gel exhibited excellent CO2 efficiencies of 0.36 and 0.38 mg CO2 per gram sorbent, respectively, which are higher than the 15% efficiency of the unmodified adsorbent. The results showed that the modified silica gel had high CO2 efficiency during the first three adsorption‒regeneration cycles when the water content and amine loading increased. Moreover, the nitrogen content increased with increasing water content, leading to an increase in the adsorption capacity.
- Open Access
- 31 December 2024
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 17 (6) , 69-80
Biogas Feeding Position for Co-Firing with Biomass in Bubbling Fluidized Bed Boiler using Computational Fluid Dynamics
Reduction of coal use in boilers is necessary to help lessen the impact on the ozone layer without sacrificing boiler efficiency due to rising CO2 emissions and energy consumption. Since agricultural industries produce a large amount of waste biomass, biomass could be used as an energy source. Anaerobic digestion is a process that can be used to convert this waste into biogas, which can save on the expense of building a new boiler and help reduce the disposal fee. This study aims to investigate the optimal location of the biogas inlet in a biomass bubbling boiler using computational fluid dynamics (CFD) simulation to predict the feasibility of biogas co-firing in bubbling fluidized bed boilers. The objective of integrating biogas into a biomass bubbling bed boiler has been introduced. The load burner and the first row of secondary air inlets for biogas integration are compared in this study. The outcome demonstrates that the most effective position to feed biogas into the boiler is the premixed biogas in the first row of the secondary air inlet
- 31 December 2024
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 17 (6) , 69-80
Open AccessBiogas Feeding Position for Co-Firing with Biomass in Bubbling Fluidized Bed Boiler using Computational Fluid Dynamics
Reduction of coal use in boilers is necessary to help lessen the impact on the ozone layer without sacrificing boiler efficiency due to rising CO2 emissions and energy consumption. Since agricultural industries produce a large amount of waste biomass, biomass could be used as an energy source. Anaerobic digestion is a process that can be used to convert this waste into biogas, which can save on the expense of building a new boiler and help reduce the disposal fee. This study aims to investigate the optimal location of the biogas inlet in a biomass bubbling boiler using computational fluid dynamics (CFD) simulation to predict the feasibility of biogas co-firing in bubbling fluidized bed boilers. The objective of integrating biogas into a biomass bubbling bed boiler has been introduced. The load burner and the first row of secondary air inlets for biogas integration are compared in this study. The outcome demonstrates that the most effective position to feed biogas into the boiler is the premixed biogas in the first row of the secondary air inlet