Khaled Ali Al-Attab
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Khaled Ali Al-Attab has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Zainal Alimuddin Zainal
School of Mechanical Engineering, Universiti Sains Malaysia, Engineering Campus, 14300 Nibong Tebal, Penang, Malaysia
18 shared publications Ibrahim I. Enagi
Federal Polytechnic
3 shared publicationsZ.A. Zainal
3 shared publications- Ibrahim I. Enagi
Department of Mechanical Engineering, School of Engineering TechnologyFederal Polytechnic P.M.B 55, Bida, Niger State Nigeria
2 shared publications Jie Wang
School of Mechanical Engineering, Universiti Sains Malaysia, Nibong Tebal, Penang, Malaysia
2 shared publications- Lemthong Chanphavong
Department of Mechanical Engineering, Faculty of Engineering, National University of Laos, Vientiane, Lao PDR
2 shared publications
Latest Publications
- Open Access
- 30 November 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Numerical Heat Transfer
- Vol. 27 (1) , 146-170
Modeling of Basin Type Single Slope Solar Still Under Local Climate Conditions in Yemen
The economic crises and instability caused by the conflict in Yemen prevents the establishment of medium and large-scale water desalination plants to overcome the sever water scarcity in the high population major cities. This paper investigates small scale solar still water desalination technology as a potential candidate to aid with the production of fresh water to reduce the accelerated depletion of underground water reserves in Yemen. Water stills have the advantage of low capital cost and no operational cost as it utilizes the high solar radiation intensity in the coastal areas to evaporate water. This paper proposes and compares two models to simulate the performance of solar still following steady-state and transient modelling approaches, with in-depth evaluation of the different parameters affecting the performance. The transient model showed better prediction of the temperature profiles of the solar still when compared to other experimental and mathematical modelling studies. The small scale solar still showed water production yield of about 1.9 kg/day, with maximum hourly yield of about 0.27 kg/h.
- 30 November 2024
- Published by Akademia Baru Publishing in Journal of Advanced Research in Numerical Heat Transfer
- Vol. 27 (1) , 146-170
Open AccessModeling of Basin Type Single Slope Solar Still Under Local Climate Conditions in Yemen
The economic crises and instability caused by the conflict in Yemen prevents the establishment of medium and large-scale water desalination plants to overcome the sever water scarcity in the high population major cities. This paper investigates small scale solar still water desalination technology as a potential candidate to aid with the production of fresh water to reduce the accelerated depletion of underground water reserves in Yemen. Water stills have the advantage of low capital cost and no operational cost as it utilizes the high solar radiation intensity in the coastal areas to evaporate water. This paper proposes and compares two models to simulate the performance of solar still following steady-state and transient modelling approaches, with in-depth evaluation of the different parameters affecting the performance. The transient model showed better prediction of the temperature profiles of the solar still when compared to other experimental and mathematical modelling studies. The small scale solar still showed water production yield of about 1.9 kg/day, with maximum hourly yield of about 0.27 kg/h.
- 3 July 2024
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 15 (6) , 9653-9678
Techno-economic and thermodynamic analyses of a novel CCHP system driven by a solid oxide fuel cell integrated with a biomass gasification unit and a double-effect LiBr-water absorption chiller or heat cycle and carbon capture
- 3 July 2024
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 15 (6) , 9653-9678
Techno-economic and thermodynamic analyses of a novel CCHP system driven by a solid oxide fuel cell integrated with a biomass gasification unit and a double-effect LiBr-water absorption chiller or heat cycle and carbon capture
- Open Access
- 30 September 2023
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 15 (11) , 181-200
Numerical Investigation and Comparison Between Internal and External Liquid Biofuel Pre-Evaporation in Micro Gas Turbine Chamber
Due to the current global crises related to fossil fuels (prices up and sources shortage) and in order to diminish the remnants and the negative effects of harmful gas emission (CO and NOx), the fielded researchers and academics try to find alternative source of fossil fuel. Bio fuels consider one of promised source of clean energy. Palm vegetable oil widely separated in Malaysia which considered one of dominant production of this oil globally. Atomization and evaporation radically represent a challenge when using liquid fuel especially fuels with high viscosity and density which is not easy to atomize and evaporate without pre-heating or blende it. A numerical investigation has been proposed to do comparison between two different external evaporative chamber and internal evaporation without using conventional liquid fuel evaporation methods. Findings revealed that both configurations have a good performance in term of emission concentrations and turbine inlet temperature (TIT) which was about 899 C with chamber using internal recycle tube evaporation with CO emission about 183 ppm with outer pre-evaporation chamber. Chamber with internal evaporation was chosen due to technical and fabrication reasons. Besides that, a six different inlet and exhaust ducting ports tested with the chosen chamber with internal recycle tube evaporation chamber, all configurations revealed a non-symmetrical flame flow near chamber exhaust which is not desirable as it will cause turbine unstable operation. The configuration with square duct exhaust was suitable with stable and symmetric flame flow field and slight small CO emission about 312 ppm.
- 30 September 2023
- Published by Akademia Baru Publishing in CFD Letters
- Vol. 15 (11) , 181-200
Open AccessNumerical Investigation and Comparison Between Internal and External Liquid Biofuel Pre-Evaporation in Micro Gas Turbine Chamber
Due to the current global crises related to fossil fuels (prices up and sources shortage) and in order to diminish the remnants and the negative effects of harmful gas emission (CO and NOx), the fielded researchers and academics try to find alternative source of fossil fuel. Bio fuels consider one of promised source of clean energy. Palm vegetable oil widely separated in Malaysia which considered one of dominant production of this oil globally. Atomization and evaporation radically represent a challenge when using liquid fuel especially fuels with high viscosity and density which is not easy to atomize and evaporate without pre-heating or blende it. A numerical investigation has been proposed to do comparison between two different external evaporative chamber and internal evaporation without using conventional liquid fuel evaporation methods. Findings revealed that both configurations have a good performance in term of emission concentrations and turbine inlet temperature (TIT) which was about 899 C with chamber using internal recycle tube evaporation with CO emission about 183 ppm with outer pre-evaporation chamber. Chamber with internal evaporation was chosen due to technical and fabrication reasons. Besides that, a six different inlet and exhaust ducting ports tested with the chosen chamber with internal recycle tube evaporation chamber, all configurations revealed a non-symmetrical flame flow near chamber exhaust which is not desirable as it will cause turbine unstable operation. The configuration with square duct exhaust was suitable with stable and symmetric flame flow field and slight small CO emission about 312 ppm.
- Open Access
- 18 July 2023
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 106 (2) , 54-67
Hydrogen Production Enhancement and Tar Reduction using New Three-Layer Annular Downdraft Air-Steam Biomass Gasifier
This study presents experimental analysis of biomass air-steam gasification for the enhancement of H2 production in producer gas (PG). Wood pellets which are widely available in Malaysia are used in this investigation. A pilot scale downdraft gasifier based on new three-layers annular reactor design was implemented to produce hydrogen enriched PG. The reactor is initially heated using hot flue gas from LPG combustion which is switched to PG when the reactor reaches stable operation. The effect of steam to biomass (S/B) ratio from 1.1 to 1.5 on PG quality in terms of gas composition, HHV and tar contamination is studied. Maximum H2 production of 27.7% was achieved at optimum air flow rate of 75 LPM and S/B ratio of 1.2. At the optimum air flow rate, HHV and tar contamination in PG where in the range of 5.06 - 6.08 MJ/Nm3 and 187 - 30mg/m3, respectively.
- 18 July 2023
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 106 (2) , 54-67
Open AccessHydrogen Production Enhancement and Tar Reduction using New Three-Layer Annular Downdraft Air-Steam Biomass Gasifier
This study presents experimental analysis of biomass air-steam gasification for the enhancement of H2 production in producer gas (PG). Wood pellets which are widely available in Malaysia are used in this investigation. A pilot scale downdraft gasifier based on new three-layers annular reactor design was implemented to produce hydrogen enriched PG. The reactor is initially heated using hot flue gas from LPG combustion which is switched to PG when the reactor reaches stable operation. The effect of steam to biomass (S/B) ratio from 1.1 to 1.5 on PG quality in terms of gas composition, HHV and tar contamination is studied. Maximum H2 production of 27.7% was achieved at optimum air flow rate of 75 LPM and S/B ratio of 1.2. At the optimum air flow rate, HHV and tar contamination in PG where in the range of 5.06 - 6.08 MJ/Nm3 and 187 - 30mg/m3, respectively.
- 6 June 2023
- Published by Elsevier in Renewable Energy
- Vol. 214, 154-167
New annular steam-biomass reactor design for hydrogen-enriched producer gas production
- 6 June 2023
- Published by Elsevier in Renewable Energy
- Vol. 214, 154-167
New annular steam-biomass reactor design for hydrogen-enriched producer gas production
- Open Access
- 29 September 2022
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 98 (2) , 175-204
Steam Gasification of Biomass for Hydrogen Production – A Review and Outlook
This article summarizes various biomass gasification methods and explains their advantages and disadvantages. First, theoretical aspects of gasification and the variety in reactor designs are overviewed. Despite the eminent effect of reactor design on gas product quality, gasification agents remain the dominant factor that determines the gas composition. Steam gasification is a thermochemical process that promotes organic carbonaceous substances into carbon monoxide and hydrogen while reducing the presence of dilutants. However, several obstacles during gasification and downstream processing have to be overcome to achieve adequate maturity. Gasification characteristics of steam were compared to the other gasification agents, including air, oxygen and CO2. The key performance parameters affecting steam gasification include raw material properties, additive and catalytic materials. While the key operating parameters include operating temperature, residence time, superficial velocity, equivalence ratio and steam-to-biomass ratio. Finally, the techno-economic evaluation and challenges facing the commercialization of steam gasification were discussed.
- 29 September 2022
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 98 (2) , 175-204
Open AccessSteam Gasification of Biomass for Hydrogen Production – A Review and Outlook
This article summarizes various biomass gasification methods and explains their advantages and disadvantages. First, theoretical aspects of gasification and the variety in reactor designs are overviewed. Despite the eminent effect of reactor design on gas product quality, gasification agents remain the dominant factor that determines the gas composition. Steam gasification is a thermochemical process that promotes organic carbonaceous substances into carbon monoxide and hydrogen while reducing the presence of dilutants. However, several obstacles during gasification and downstream processing have to be overcome to achieve adequate maturity. Gasification characteristics of steam were compared to the other gasification agents, including air, oxygen and CO2. The key performance parameters affecting steam gasification include raw material properties, additive and catalytic materials. While the key operating parameters include operating temperature, residence time, superficial velocity, equivalence ratio and steam-to-biomass ratio. Finally, the techno-economic evaluation and challenges facing the commercialization of steam gasification were discussed.
- Open Access
- 24 May 2022
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 94 (2) , 184-199
Design and Characteristics of a New Pre-Evaporation Chamber Geometry for Low-Grade Palm Oil Fuel Evaporation for Micro Gas Turbine Application
Recent increase in fuel prices, greenhouse emissions, global warming issue, as well as future predictions regarding fossil fuel depletion concerns have prompted widespread research on carbon-neutral renewable liquid biofuels as an alternative of petroleum fuels. In the present study, a numerical approach was used to design and optimize a novel design of pre-evaporation chamber, to pre-evaporate crude palm oil fuel using exhaust gas recycling to allow partially premixed fuel vapors to be introduced to the main combustion chamber. Discrete Phase Model (DPM) and species non-premixed model used in ANSYS-FLUENT software to simulate fuel evaporation. The pre-chamber optimization included the addition of variable number of revolve geometry to the walls to induce turbulence and to enhance the cyclonic motion caused by the tangential hot exhaust gas inlets with different fuel injection configurations. The number of revolves was varied in the range of 5-8 and diameter range of 40-90 mm with three injector configurations. The results revealed that the optimum chamber geometry consist of 7 revolves with 70 mm diameter with fuel evaporation rate about 0.0023kg/s and fuel evaporation percentage about 89%. Increasing the exhaust gas temperature from 950 °C up to 1050°C did not show a significant fuel evaporation enhancement. Results also showed that the evaporation enhancement is proportional to the number of fuel injectors where evaporation increased gradually from 73% to 89% when increasing number of injectors from 1 to 3.
- 24 May 2022
- Published by Akademia Baru Publishing in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
- Vol. 94 (2) , 184-199
Open AccessDesign and Characteristics of a New Pre-Evaporation Chamber Geometry for Low-Grade Palm Oil Fuel Evaporation for Micro Gas Turbine Application
Recent increase in fuel prices, greenhouse emissions, global warming issue, as well as future predictions regarding fossil fuel depletion concerns have prompted widespread research on carbon-neutral renewable liquid biofuels as an alternative of petroleum fuels. In the present study, a numerical approach was used to design and optimize a novel design of pre-evaporation chamber, to pre-evaporate crude palm oil fuel using exhaust gas recycling to allow partially premixed fuel vapors to be introduced to the main combustion chamber. Discrete Phase Model (DPM) and species non-premixed model used in ANSYS-FLUENT software to simulate fuel evaporation. The pre-chamber optimization included the addition of variable number of revolve geometry to the walls to induce turbulence and to enhance the cyclonic motion caused by the tangential hot exhaust gas inlets with different fuel injection configurations. The number of revolves was varied in the range of 5-8 and diameter range of 40-90 mm with three injector configurations. The results revealed that the optimum chamber geometry consist of 7 revolves with 70 mm diameter with fuel evaporation rate about 0.0023kg/s and fuel evaporation percentage about 89%. Increasing the exhaust gas temperature from 950 °C up to 1050°C did not show a significant fuel evaporation enhancement. Results also showed that the evaporation enhancement is proportional to the number of fuel injectors where evaporation increased gradually from 73% to 89% when increasing number of injectors from 1 to 3.
Design optimization of trio concept combustor geometry for low-grade biomass producer gas combustion