Brendan C. Barry
Brendan C. Barry has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Adam Penczek
Department of Power Electronics and Energy Control Systems, Faculty of Electrical Engineering, Automatics, Computer Science and Biomedical Engineering, AGH University of Science and Technology, al. Mickiewicza 30, 30-059 Krakow, Poland
1 shared publication - Andrzej Mondzik
AGH University of Krakow
1 shared publication - Christoph Kessler
Linköping University
1 shared publication - Diarmuid N. Hogan
Advanced Energy, Cork, Ireland
1 shared publication - John G. Hayes
University College Cork, Ireland
1 shared publication - Lu Li
School of Astronautics, Beihang University, Beijing 100191, China
1 shared publication
Latest Publications
- Open Access
- 22 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (5) , 6771-6786
Hysteretic Current Mode Control of a Wide Output Voltage Three-Level Converter
Multilevel dc–dc converters can offer very high efficiency but have been generally limited to voltage mode control schemes for wide output voltage applications due to difficulties with current mode control near certain duty-cycles. For applications that require current mode control, this article proposes a hysteretic current mode control scheme which allows cycle-by-cycle control of multilevel converters over a wide duty-cycle range while also allowing operation at the critical duty-cycles found in multilevel converters. This enables high-efficiency solutions for applications that require a wide range of tightly regulated outputs, such as capacitor and battery charging, direct laser diode driving, and motor control. This is achieved using a multimode control scheme with ramped current references, a maximum interval timer, and reference offsetting for flying capacitor balancing. This control scheme is verified in Simulink modeling and implemented on a prototype three-level buck converter using a combination of a low-cost field programmable gate array and discrete analog circuitry. Alternative implementations are also described.
- 22 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (5) , 6771-6786
Open AccessHysteretic Current Mode Control of a Wide Output Voltage Three-Level Converter
Multilevel dc–dc converters can offer very high efficiency but have been generally limited to voltage mode control schemes for wide output voltage applications due to difficulties with current mode control near certain duty-cycles. For applications that require current mode control, this article proposes a hysteretic current mode control scheme which allows cycle-by-cycle control of multilevel converters over a wide duty-cycle range while also allowing operation at the critical duty-cycles found in multilevel converters. This enables high-efficiency solutions for applications that require a wide range of tightly regulated outputs, such as capacitor and battery charging, direct laser diode driving, and motor control. This is achieved using a multimode control scheme with ramped current references, a maximum interval timer, and reference offsetting for flying capacitor balancing. This control scheme is verified in Simulink modeling and implemented on a prototype three-level buck converter using a combination of a low-cost field programmable gate array and discrete analog circuitry. Alternative implementations are also described.
- 23 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 33 (9) , 8052-8064
Small-Signal Model of the Two-Phase Interleaved Coupled-Inductor Boost Converter
A coupled-inductor dc-dc converter has several modes of operation in continuous-conduction mode (CCM) and discontinuous-conduction mode (DCM), and is quite complex. This paper presents the derivation of the complete small-signal model of a two-phase interleaved dc-dc boost converter utilizing a single-core coupled-inductor operating in both CCM and DCM. Several small-signal models are required to fully model the converter due to the complexity of the converter operating in DCM. The transfer functions are then derived from these small-signal models. The theoretical analysis is validated experimentally using frequency sweeps from a 1-kW prototype.
- 23 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 33 (9) , 8052-8064
Small-Signal Model of the Two-Phase Interleaved Coupled-Inductor Boost Converter
A coupled-inductor dc-dc converter has several modes of operation in continuous-conduction mode (CCM) and discontinuous-conduction mode (DCM), and is quite complex. This paper presents the derivation of the complete small-signal model of a two-phase interleaved dc-dc boost converter utilizing a single-core coupled-inductor operating in both CCM and DCM. Several small-signal models are required to fully model the converter due to the complexity of the converter operating in DCM. The transfer functions are then derived from these small-signal models. The theoretical analysis is validated experimentally using frequency sweeps from a 1-kW prototype.
- 1 February 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 398-402
Efficient Execution of SkePU Skeleton Programs on the Low-Power Multicore Processor Myriad2
SkePU is a state-of-the-art skeleton programming library for high-level portable programming and efficient execution on heterogeneous parallel computer systems, with a publically available implementation for general-purpose multicore CPU and multi-GPU systems. This paper presents the design, implementation and evaluation of a new back-end of the SkePU skeleton programming library for the new low-power multicore processor Myriad2 by Movidius Ltd. This enables seamless code portability of SkePU applications across both HPC and embedded (Myriad2) parallel computing systems, with decent performance, on these architecturally very diverse types of execution platforms.
- 1 February 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 398-402
Efficient Execution of SkePU Skeleton Programs on the Low-Power Multicore Processor Myriad2
SkePU is a state-of-the-art skeleton programming library for high-level portable programming and efficient execution on heterogeneous parallel computer systems, with a publically available implementation for general-purpose multicore CPU and multi-GPU systems. This paper presents the design, implementation and evaluation of a new back-end of the SkePU skeleton programming library for the new low-power multicore processor Myriad2 by Movidius Ltd. This enables seamless code portability of SkePU applications across both HPC and embedded (Myriad2) parallel computing systems, with decent performance, on these architecturally very diverse types of execution platforms.