Alexey L. Rukosuev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Alexey L. Rukosuev has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Alexis V. Kudryashov
Russian Academy of Sciences
35 shared publications - Vadim V. Samarkin
Moscow State Open Univ. (Russian Federation)
27 shared publications - Alexander Alexandrov
Moscow State University of Mechanical Engineering, Moscow, Russia
18 shared publications - Julia Sheldakova
Russian Academy of Sciences
17 shared publications - Valentina Zavalova
Joint Institute for High Temperatures, Russian Academy of Sciences, Moscow, Russia
16 shared publications - Pavel Romanov
Moscow State Open Univ. (Russian Federation)
9 shared publications
Latest Publications
- 6 January 2026
- Published by Sadovsky Institute of Geosphere Dynamics in ДИНАМИЧЕСКИЕ ПРОЦЕССЫ В ГЕОСФЕРАХ
- Vol. 17 (4) , 115-129
ЛАБОРАТОРНАЯ МОДЕЛЬ АДАПТИВНОЙ ОПТИЧЕСКОЙ СИСТЕМЫ, ВКЛЮЧАЮЩАЯ ГЕНЕРАТОР АТМОСФЕРНОЙ ТУРБУЛЕНТНОСТИ И СИСТЕМУ КОРРЕКЦИИ СОЗДАННЫХ ФАЗОВЫХ ФЛУКТУАЦИЙ
Атмосферная турбулентность вызывает искажения волнового фронта распространяющегося оптического излучения. Это приводит к ухудшению разрешения изображений в астрономических телескопах и значительно снижает плотность мощности излучения на цели при фокусировке. Влияние турбулентных флуктуаций на волновой фронт можно исследовать в лабораторных условиях с использованием деформируемого зеркалa в качестве генератора турбулентности, а в качестве измерителя искажений волнового фронта — датчика волнового фронта. Мы разработали программный симулятор и экспериментальную установку для генерации фазовых флуктуаций атмосферной турбулентности, а также адаптивную оптическую систему для компенсации вызванных ими аберраций. Обе системы используют биморфные деформируемых зеркала диаметром 60 мм с 92 каналами управления и два корректора наклона. Волновой фронт измеряется с помощью высокоскоростного датчика волнового фронта Шака–Гартмана на базе промышленной CMOS-камеры. Система достигла частоты коррекции 500 Гц, при этом амплитуда аберраций снизилась с 2.6 мкм до 0.3 мкм в процессе коррекции. Применение корректора наклона позволило уменьшить диапазон дрожания центроида фокального пятна в 2–3 раза. Atmospheric turbulence causes distortions in the wavefront of propagating optical radiation. This leads to a degradation of image resolution in astronomical telescopes and significantly reduces the power density of radiation on the target when focusing. The influence of turbulent fluctuations on the wavefront can be studied in laboratory conditions using a deformable mirror as a phase fluctuations generator and a wavefront sensor as a distortion measurer. We have developed a software simulator and an experimental setup forgenerating atmospheric turbulence phase fluctuations, as well as an adaptive optical system to compensate for the induced aberrations. Both systems use 60-mm diameter bimorph deformable mirrors with 92 control channels and two tip-tilt correctors. The wavefront is measured using a high-speed Shack-Hartmann wavefront sensor based on an industrial CMOS camera. The system achieved a correction frequency of 600 Hz, reducing the aberration amplitude from 2.6 μm to 0.3 μm during the correction process. Theapplication of the tip-tilt corrector reduced the range of focal spot centroid jitter by a factor of 2–3.
- 6 January 2026
- Published by Sadovsky Institute of Geosphere Dynamics in ДИНАМИЧЕСКИЕ ПРОЦЕССЫ В ГЕОСФЕРАХ
- Vol. 17 (4) , 115-129
ЛАБОРАТОРНАЯ МОДЕЛЬ АДАПТИВНОЙ ОПТИЧЕСКОЙ СИСТЕМЫ, ВКЛЮЧАЮЩАЯ ГЕНЕРАТОР АТМОСФЕРНОЙ ТУРБУЛЕНТНОСТИ И СИСТЕМУ КОРРЕКЦИИ СОЗДАННЫХ ФАЗОВЫХ ФЛУКТУАЦИЙ
Атмосферная турбулентность вызывает искажения волнового фронта распространяющегося оптического излучения. Это приводит к ухудшению разрешения изображений в астрономических телескопах и значительно снижает плотность мощности излучения на цели при фокусировке. Влияние турбулентных флуктуаций на волновой фронт можно исследовать в лабораторных условиях с использованием деформируемого зеркалa в качестве генератора турбулентности, а в качестве измерителя искажений волнового фронта — датчика волнового фронта. Мы разработали программный симулятор и экспериментальную установку для генерации фазовых флуктуаций атмосферной турбулентности, а также адаптивную оптическую систему для компенсации вызванных ими аберраций. Обе системы используют биморфные деформируемых зеркала диаметром 60 мм с 92 каналами управления и два корректора наклона. Волновой фронт измеряется с помощью высокоскоростного датчика волнового фронта Шака–Гартмана на базе промышленной CMOS-камеры. Система достигла частоты коррекции 500 Гц, при этом амплитуда аберраций снизилась с 2.6 мкм до 0.3 мкм в процессе коррекции. Применение корректора наклона позволило уменьшить диапазон дрожания центроида фокального пятна в 2–3 раза. Atmospheric turbulence causes distortions in the wavefront of propagating optical radiation. This leads to a degradation of image resolution in astronomical telescopes and significantly reduces the power density of radiation on the target when focusing. The influence of turbulent fluctuations on the wavefront can be studied in laboratory conditions using a deformable mirror as a phase fluctuations generator and a wavefront sensor as a distortion measurer. We have developed a software simulator and an experimental setup forgenerating atmospheric turbulence phase fluctuations, as well as an adaptive optical system to compensate for the induced aberrations. Both systems use 60-mm diameter bimorph deformable mirrors with 92 control channels and two tip-tilt correctors. The wavefront is measured using a high-speed Shack-Hartmann wavefront sensor based on an industrial CMOS camera. The system achieved a correction frequency of 600 Hz, reducing the aberration amplitude from 2.6 μm to 0.3 μm during the correction process. Theapplication of the tip-tilt corrector reduced the range of focal spot centroid jitter by a factor of 2–3.
- 21 November 2025
- Published by Technosphera JSC in PHOTONICS Russia
- Vol. 19 (7)
Стабилизация направления распространения широкоапертурного светового пучка с использованием квадрантных фотодиодов
Статья посвящена проблеме стабилизации направления распространения широкоапертурных лазерных пучков в условиях, когда размер пучка существенно превышает габариты стандартных квадрантных фотоприемников. Анализируются две принципиальные схемы стабилизации: с зависимыми и независимыми контурами управления, и показывается, что первая схема имеет фундаментальное ограничение из-за высокой обусловленности матрицы влияния. В качестве решения предлагается система с двумя независимыми контурами, которая не требует матричных вычислений и демонстрирует высокую точность позиционирования пучка, достаточную для практического применения в лазерных системах дальней связи и фокусировки.
- 21 November 2025
- Published by Technosphera JSC in PHOTONICS Russia
- Vol. 19 (7)
Стабилизация направления распространения широкоапертурного светового пучка с использованием квадрантных фотодиодов
Статья посвящена проблеме стабилизации направления распространения широкоапертурных лазерных пучков в условиях, когда размер пучка существенно превышает габариты стандартных квадрантных фотоприемников. Анализируются две принципиальные схемы стабилизации: с зависимыми и независимыми контурами управления, и показывается, что первая схема имеет фундаментальное ограничение из-за высокой обусловленности матрицы влияния. В качестве решения предлагается система с двумя независимыми контурами, которая не требует матричных вычислений и демонстрирует высокую точность позиционирования пучка, достаточную для практического применения в лазерных системах дальней связи и фокусировки.
- 1 September 2021
- Published by Pleiades Publishing Ltd in Izvestiya, Physics of the Solid Earth
- Vol. 57 (5) , 789-794
Laboratory Simulation of Atmospheric Turbulence in the Problem of Correcting Laser Radiation Wavefront Distortions by Using a Fast Adaptive Optical System
—Atmospheric turbulence has been simulated under laboratory conditions, where a household heat fan has been used as a source of air flows of different temperatures. The wavefront distortions of laser radiation passing through a heated air flow have been studied by means of a Shack-Hartmann wavefront sensor, which is part of a fast adaptive optical system that has a correction rate of up to 2000 Hz (frames per second). The energy spectra of laser radiation wavefront disturbances are presented, which help determine the frequency bandwidth of the disturbing effect. Based on the calculated Fried parameter, a graph is plotted for the turbulent flow, which compares the results of the laboratory simulation with the real conditions of the Earth’s atmosphere.
- 1 September 2021
- Published by Pleiades Publishing Ltd in Izvestiya, Physics of the Solid Earth
- Vol. 57 (5) , 789-794
Laboratory Simulation of Atmospheric Turbulence in the Problem of Correcting Laser Radiation Wavefront Distortions by Using a Fast Adaptive Optical System
—Atmospheric turbulence has been simulated under laboratory conditions, where a household heat fan has been used as a source of air flows of different temperatures. The wavefront distortions of laser radiation passing through a heated air flow have been studied by means of a Shack-Hartmann wavefront sensor, which is part of a fast adaptive optical system that has a correction rate of up to 2000 Hz (frames per second). The energy spectra of laser radiation wavefront disturbances are presented, which help determine the frequency bandwidth of the disturbing effect. Based on the calculated Fried parameter, a graph is plotted for the turbulent flow, which compares the results of the laboratory simulation with the real conditions of the Earth’s atmosphere.
- 2 August 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (23) , 6719-6724
High-spatial resolution stacked-actuator deformable mirror for correction of atmospheric wavefront aberrations
Deformable mirrors are vital components of any adaptive optical system. Considering such a crucial role in compensation of incident wavefront distortions, the main requirements are imposed on these elements that determine performance of the entire system. To correct for phase distortions in high-power laser complexes a stacked-actuator deformable mirror with water cooling was developed. The main characteristics of the mirror, such as the initial surface profile (flatness), response functions of the actuators, maximal stroke, and amplitude-frequency characteristics are presented in this paper. Experimental investigations of the proposed cooling method of the mirror surface through actuators were performed.
- 2 August 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (23) , 6719-6724
High-spatial resolution stacked-actuator deformable mirror for correction of atmospheric wavefront aberrations
Deformable mirrors are vital components of any adaptive optical system. Considering such a crucial role in compensation of incident wavefront distortions, the main requirements are imposed on these elements that determine performance of the entire system. To correct for phase distortions in high-power laser complexes a stacked-actuator deformable mirror with water cooling was developed. The main characteristics of the mirror, such as the initial surface profile (flatness), response functions of the actuators, maximal stroke, and amplitude-frequency characteristics are presented in this paper. Experimental investigations of the proposed cooling method of the mirror surface through actuators were performed.
- 21 March 2019
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10904, 54
Stacked-actuators deformable mirror vs bimorph mirror for laser beam shaping
We present our latest research results on intensity distribution transformation from Gaussian to a flattop and doughnut. The theoretical calculations and experimental results of the efficiency of different types of deformable mirrors are given. During the experiments the wavefront was measured with Shack-Hartmann sensor and then modified with bimorph deformable mirror to reach the desired intensity distribution in the far-field. Then the bimorph mirror was substituted with the stacked-actuators deformable mirror to confirm the simulations.
- 21 March 2019
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10904, 54
Stacked-actuators deformable mirror vs bimorph mirror for laser beam shaping
We present our latest research results on intensity distribution transformation from Gaussian to a flattop and doughnut. The theoretical calculations and experimental results of the efficiency of different types of deformable mirrors are given. During the experiments the wavefront was measured with Shack-Hartmann sensor and then modified with bimorph deformable mirror to reach the desired intensity distribution in the far-field. Then the bimorph mirror was substituted with the stacked-actuators deformable mirror to confirm the simulations.
- 1 September 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 104-105
Large aperture bimorph deformable mirror for extremely high power laser systems
In this work we present our recent results in modeling and fabrication of large aperture deformable mirrors first of all for laser beam correction but also for astronomical applications. Right now our company can produce bimorph mirrors with diameter from 200 to 500 mm. One of the main new advantages of our technology is that we can easily substitute damaged reflecting surface of our mirrors. Also, these wavefront correctors could be efficiently used in wide aperture high power lasers and laser systems.
- 1 September 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 104-105
Large aperture bimorph deformable mirror for extremely high power laser systems
In this work we present our recent results in modeling and fabrication of large aperture deformable mirrors first of all for laser beam correction but also for astronomical applications. Right now our company can produce bimorph mirrors with diameter from 200 to 500 mm. One of the main new advantages of our technology is that we can easily substitute damaged reflecting surface of our mirrors. Also, these wavefront correctors could be efficiently used in wide aperture high power lasers and laser systems.
- 1 September 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21601518,p. 91-92
Adaptive system for high power (more than 100 kW) CW CO2 lasers
In this paper we consider the design and realization of wide aperture adaptive system to correct for high power CW CO2 laser radiation. Two new approaches for development of the wavefront sensors to measure 10 μ laser radiation are considered.
- 1 September 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 21601518,p. 91-92
Adaptive system for high power (more than 100 kW) CW CO2 lasers
In this paper we consider the design and realization of wide aperture adaptive system to correct for high power CW CO2 laser radiation. Two new approaches for development of the wavefront sensors to measure 10 μ laser radiation are considered.
- 12 March 2013
- Published by SPIE-Intl Soc Optical Eng
- p. 860003-860003-7
Extremely high power CO2laser beam correction
- 12 March 2013
- Published by SPIE-Intl Soc Optical Eng
- p. 860003-860003-7
Extremely high power CO2laser beam correction
- 9 February 2012
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8236, 82360L-82360L-6
New Hartmann wavefront sensor for high power CO 2 lasers
This paper presents the two types of Hartmann wavefront sensors to measure the aberrations of CO2 laser radiation. One sensor is baser on commercially available IR camera while the second one - on so-called thing film sensors. We discuss both positive and negative attributes of these sensors and the possibility to use them in the real laser systems.
- 9 February 2012
- Published by SPIE-Intl Soc Optical Eng
- Vol. 8236, 82360L-82360L-6
New Hartmann wavefront sensor for high power CO 2 lasers
This paper presents the two types of Hartmann wavefront sensors to measure the aberrations of CO2 laser radiation. One sensor is baser on commercially available IR camera while the second one - on so-called thing film sensors. We discuss both positive and negative attributes of these sensors and the possibility to use them in the real laser systems.
- 10 February 2011
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7913, 791309-791309-9
Shack-Hartmann wavefront sensor and its problems
Shack-Hartman wavefront sensors are widely used in scientific investigations of wavefronts and also, as a component of the closed-loop adaptive optical system, intended to correct for laser beam aberrations. This paper presents successful application of such type sensors in the laser systems investigations to obtain high quality laser radiation. Results of investigations of wavefronts of modern high power solid-state lasers are given in this paper.
- 10 February 2011
- Published by SPIE-Intl Soc Optical Eng
- Vol. 7913, 791309-791309-9
Shack-Hartmann wavefront sensor and its problems
Shack-Hartman wavefront sensors are widely used in scientific investigations of wavefronts and also, as a component of the closed-loop adaptive optical system, intended to correct for laser beam aberrations. This paper presents successful application of such type sensors in the laser systems investigations to obtain high quality laser radiation. Results of investigations of wavefronts of modern high power solid-state lasers are given in this paper.