Thomas Neumeyer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Thomas Neumeyer has a total of 98 co-authors. Here are the top co-authors by number of shared publications:
- Volker Altstädt
Polymer Engineering, University of Bayreuth, Bayreuth, Germany
7 shared publications - Jens Schlimbach
Leibniz-Institut für Verbundwerkstoffe GmbH
3 shared publications Michael Kropka
Neue Materialien Bayreuth GmbH, Bayreuth, Deutschland
3 shared publicationsFlorian Gortner
2 shared publicationsGiancarlo Bonotto
University of Bayreuth
2 shared publicationsKarthick Selvaraj
Neue Materialien Bayreuth GmbH, Bayreuth, Deutschland
2 shared publications
Latest Publications
- 3 November 2026
- Published by Elsevier in Composites Part B: Engineering
- Vol. 330
Process-structure-relationship analysis of recycled carbon fiber composites
- 3 November 2026
- Published by Elsevier in Composites Part B: Engineering
- Vol. 330
Process-structure-relationship analysis of recycled carbon fiber composites
- Open Access
- 30 August 2026
- Published by Taylor & Francis in Advanced Manufacturing: Polymer & Composites Science
- Vol. 12 (1)
Inline metrology in composite winding processes – a comprehensive view on state of the art, current developments and perspectives
- 30 August 2026
- Published by Taylor & Francis in Advanced Manufacturing: Polymer & Composites Science
- Vol. 12 (1)
Open AccessInline metrology in composite winding processes – a comprehensive view on state of the art, current developments and perspectives
- Open Access
- 11 August 2026
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 211
Implementation of automated process-level GWP calculation for a high-speed thermoplastic tape laying process
- 11 August 2026
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 211
Open AccessImplementation of automated process-level GWP calculation for a high-speed thermoplastic tape laying process
- Open Access
- 11 July 2026
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 210
Investigation on the influence of process parameters on the pseudo-plastic deformation behavior of staple fiber organic sheets
- 11 July 2026
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 210
Open AccessInvestigation on the influence of process parameters on the pseudo-plastic deformation behavior of staple fiber organic sheets
- Open Access
- 14 April 2026
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 387, 131-141
The First European Benchmark Exercise on Squeeze Flow Testing of High-Performance C-SMCs: Review
Squeeze-flow testing is a commonly used experimental method for characterising the flow behaviour of high-performance C-SMCs under typical compression moulding conditions. A European benchmark exercise involving 14 research institutes is currently being conducted to identify the sources of variability in squeeze flow testing results and to support the development of a standardised testing methodology. Experimental testing of five C-SMC materials has been completed using a well-defined testing procedure.This paper focuses on the data processing stage of the benchmark exercise, in which experimental data collected from all participants are processed and analysed to extract information on raw material variability, force–gap height relationships, and flow-front profiles. Qualitative assessment of these results is used to identify the critical sources of variability, which subsequently informs a more detailed statistical analysis.
- 14 April 2026
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 387, 131-141
Open AccessThe First European Benchmark Exercise on Squeeze Flow Testing of High-Performance C-SMCs: Review
Squeeze-flow testing is a commonly used experimental method for characterising the flow behaviour of high-performance C-SMCs under typical compression moulding conditions. A European benchmark exercise involving 14 research institutes is currently being conducted to identify the sources of variability in squeeze flow testing results and to support the development of a standardised testing methodology. Experimental testing of five C-SMC materials has been completed using a well-defined testing procedure.This paper focuses on the data processing stage of the benchmark exercise, in which experimental data collected from all participants are processed and analysed to extract information on raw material variability, force–gap height relationships, and flow-front profiles. Qualitative assessment of these results is used to identify the critical sources of variability, which subsequently informs a more detailed statistical analysis.
- Open Access
- 10 April 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1182, 135-146
A Unified Simulation Environment for Thermoforming and Distortion Prediction of CFRTP Aircraft Components
This paper presents a comprehensive fully integrated polymer composite thermoforming process simulation chain developed in ANSYS LS-DYNA®, covering the full manufacturing sequence from automated preform creation to final part cooling. The entire simulation consists of three distinct phases, namely, thermoforming, cooling (within the tool) and manufacturing-induced dimensional distortion after demolding (spring-back), where distortions develop as the part is removed from the tooling and finally cools to room temperature. The simulation framework employs a modular model structure consisting of tooling, a preform holding system, and a detailed preform representation based on a semi-discrete unit cell approach. Individual laminate plies are modeled using a combination of beam, solid, and shell elements to accurately capture temperature-dependent bending, shear, and thermal behavior of the preform. To ensure industrial applicability, an automated preform meshing strategy has also been developed, utilizing tape placement path planning data exported from the automated tape laying process to generate simulation models with minimal manual effort. The simulation results enable the prediction of spring-angle distortions (spring-in or spring-back) and can be validated against experimental distortion measurement data from manufacturing trials of several different representative CFRTP components. The presented approach demonstrates the capability of the newly developed simulation chain to support thermoforming process development, tool geometry compensation, and robust manufacturing of complex thermoformed CFRTP structures.
- 10 April 2026
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1182, 135-146
Open AccessA Unified Simulation Environment for Thermoforming and Distortion Prediction of CFRTP Aircraft Components
This paper presents a comprehensive fully integrated polymer composite thermoforming process simulation chain developed in ANSYS LS-DYNA®, covering the full manufacturing sequence from automated preform creation to final part cooling. The entire simulation consists of three distinct phases, namely, thermoforming, cooling (within the tool) and manufacturing-induced dimensional distortion after demolding (spring-back), where distortions develop as the part is removed from the tooling and finally cools to room temperature. The simulation framework employs a modular model structure consisting of tooling, a preform holding system, and a detailed preform representation based on a semi-discrete unit cell approach. Individual laminate plies are modeled using a combination of beam, solid, and shell elements to accurately capture temperature-dependent bending, shear, and thermal behavior of the preform. To ensure industrial applicability, an automated preform meshing strategy has also been developed, utilizing tape placement path planning data exported from the automated tape laying process to generate simulation models with minimal manual effort. The simulation results enable the prediction of spring-angle distortions (spring-in or spring-back) and can be validated against experimental distortion measurement data from manufacturing trials of several different representative CFRTP components. The presented approach demonstrates the capability of the newly developed simulation chain to support thermoforming process development, tool geometry compensation, and robust manufacturing of complex thermoformed CFRTP structures.
- Open Access
- 16 September 2025
- Published by Elsevier in Materials & Design
- Vol. 259
Influencing the draping behaviour of solid epoxy prepregs by applying 3D-printed resin patterns
- 16 September 2025
- Published by Elsevier in Materials & Design
- Vol. 259
Open AccessInfluencing the draping behaviour of solid epoxy prepregs by applying 3D-printed resin patterns
- Open Access
- 2 June 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 304
Effect of inter-tow angle and temperature on the static coefficient of friction of preimpregnated tows in tow-tow and tow-metal contact
- 2 June 2025
- Published by Elsevier in Composites Part B: Engineering
- Vol. 304
Open AccessEffect of inter-tow angle and temperature on the static coefficient of friction of preimpregnated tows in tow-tow and tow-metal contact
- Open Access
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3158 (1) , 180005
Selective laser sintering on the way to industrial application: A holistic approach for a digitized demonstration factory
At present, additive manufacturing with polymers already allows the economical production of components in individual pieces or small quantities with good appli At present, additive manufacturing with polymers already allows the economical production of components in individual pieces or small quantities with good appli
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3158 (1) , 180005
Open AccessSelective laser sintering on the way to industrial application: A holistic approach for a digitized demonstration factory
At present, additive manufacturing with polymers already allows the economical production of components in individual pieces or small quantities with good appli At present, additive manufacturing with polymers already allows the economical production of components in individual pieces or small quantities with good appli
- Open Access
3D Printed, Single-Use Bioreactor with Integrated Inline Sensors for Microbial and Mammalian Cell Cultivation—A Case Study
The development of upstream bioprocesses necessitates small, instrumented bioreactors for investigating and optimizing production processes in a cost-effective manner. Due to advances in both the equipment and the materials used in additive manufacturing, 3D printing of customized bioreactors is now in the realm of possibilities. In this study, a small-scale 3D printed bioreactor suitable for mammalian and microbial cultivations was developed, featuring a working volume of 90 mL, inline pH and dissolved oxygen probes and a levitating magnetic stirrer. Aeration channels and a sampling port were printed directly into the vessel walls. Additionally, the vessel was equipped with a 3D printed customizable optical biomass-sensor. The bioreactor’s performance was evaluated through technical characterization and proof of concept cultivations, demonstrating that mixing time and oxygen mass transfer were sufficient for cultivating mammalian as well as microbial cells at high cell densities. Specifically, an Escherichia coli fed-batch cultivation achieved a maximum OD600 of 204. Furthermore, a fed-batch cultivation of an IgG antibody-producing Chinese hamster ovary cell line reached a peak viable cell density of 10.2 × 106 cells mL−1 and a maximum product titer of 2.75 g L−1. Using a three-parameter fit, the inline biomass signal could be correlated to the corresponding offline values with satisfactory accuracy, making it possible to monitor cell growth in real-time.
Open Access3D Printed, Single-Use Bioreactor with Integrated Inline Sensors for Microbial and Mammalian Cell Cultivation—A Case Study
The development of upstream bioprocesses necessitates small, instrumented bioreactors for investigating and optimizing production processes in a cost-effective manner. Due to advances in both the equipment and the materials used in additive manufacturing, 3D printing of customized bioreactors is now in the realm of possibilities. In this study, a small-scale 3D printed bioreactor suitable for mammalian and microbial cultivations was developed, featuring a working volume of 90 mL, inline pH and dissolved oxygen probes and a levitating magnetic stirrer. Aeration channels and a sampling port were printed directly into the vessel walls. Additionally, the vessel was equipped with a 3D printed customizable optical biomass-sensor. The bioreactor’s performance was evaluated through technical characterization and proof of concept cultivations, demonstrating that mixing time and oxygen mass transfer were sufficient for cultivating mammalian as well as microbial cells at high cell densities. Specifically, an Escherichia coli fed-batch cultivation achieved a maximum OD600 of 204. Furthermore, a fed-batch cultivation of an IgG antibody-producing Chinese hamster ovary cell line reached a peak viable cell density of 10.2 × 106 cells mL−1 and a maximum product titer of 2.75 g L−1. Using a three-parameter fit, the inline biomass signal could be correlated to the corresponding offline values with satisfactory accuracy, making it possible to monitor cell growth in real-time.