Jin-Ho Roh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jin-Ho Roh has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
- Jae-Wook Lee
Department of Electronics and Information Engineering, Korea Aerospace University, Goyang, Korea
4 shared publications O-Hyun Kwon
Mechanical R&D (Satellite System), LIG Nex1, Seongnam, Republic of Korea
4 shared publications- Kitae Park
Department of Electronics and Information Engineering, Korea Aerospace University, Goyang, Korea
3 shared publications - Dong-Seok Kang
Mechanical R&D (Space System), LIG Nex1, Seongnam 13488, Republic of Korea
2 shared publications - Hwa-Young Jung
Mechanical R&D (Satellite System), LIG Nex1, Seongnam, Korea
2 shared publications Jae-Sung Bae
School of Aerospace and Mechanical Engineering, Korea Aerospace University, Goyang, Gyeonggi, Republic of Korea
2 shared publications
Latest Publications
- Open Access
- 30 September 2026
- Published by Korean Institute of Electromagnetic Engineering and Science in Journal of Electromagnetic Engineering and Science
- Vol. 26 (5) , 518-528
Design and Experimental Validation of a 0.6 m Diameter K-Band CFRS Reflector Antenna for Cube Satellite Applications
This paper presents the design, fabrication, and experimental validation of a K-band reflector antenna using a triaxially woven carbonfiber-reinforced silicone (CFRS) composite for small satellite applications. The CFRS surface was formed by curing a single lamina sheet into a parabolic geometry to optimize electromagnetic performance and structural integrity. To mitigate reflection loss caused by fiber discontinuities at high frequencies, a sealed triaxial woven fabric was employed, improving surface continuity and isotropy. Waveguide-based S-parameter measurements yielded an equivalent electrical conductivity of approximately 3,686 S/m and a reflection loss of about 0.2 dB at 20 GHz. Surface profiling confirmed sub-millimeter surface accuracy, and gain degradation due to surface errors was estimated to be less than 0.1 dB. A 0.6 m parabolic reflector achieved a boresight gain of 37.4 dBi at 20 GHz, showing close agreement with full-wave simulations incorporating the measured material and geometric properties. While a conceptual umbrella-type structure was designed to assess mechanical feasibility, the experimental prototype was constructed with a fixed feed support to prioritize precise electromagnetic verification under ground-based conditions. This work provides an experimental foundation for the development of lightweight CFRS-based reflector antennas for future small satellites in low earth orbit.
- 30 September 2026
- Published by Korean Institute of Electromagnetic Engineering and Science in Journal of Electromagnetic Engineering and Science
- Vol. 26 (5) , 518-528
Open AccessDesign and Experimental Validation of a 0.6 m Diameter K-Band CFRS Reflector Antenna for Cube Satellite Applications
This paper presents the design, fabrication, and experimental validation of a K-band reflector antenna using a triaxially woven carbonfiber-reinforced silicone (CFRS) composite for small satellite applications. The CFRS surface was formed by curing a single lamina sheet into a parabolic geometry to optimize electromagnetic performance and structural integrity. To mitigate reflection loss caused by fiber discontinuities at high frequencies, a sealed triaxial woven fabric was employed, improving surface continuity and isotropy. Waveguide-based S-parameter measurements yielded an equivalent electrical conductivity of approximately 3,686 S/m and a reflection loss of about 0.2 dB at 20 GHz. Surface profiling confirmed sub-millimeter surface accuracy, and gain degradation due to surface errors was estimated to be less than 0.1 dB. A 0.6 m parabolic reflector achieved a boresight gain of 37.4 dBi at 20 GHz, showing close agreement with full-wave simulations incorporating the measured material and geometric properties. While a conceptual umbrella-type structure was designed to assess mechanical feasibility, the experimental prototype was constructed with a fixed feed support to prioritize precise electromagnetic verification under ground-based conditions. This work provides an experimental foundation for the development of lightweight CFRS-based reflector antennas for future small satellites in low earth orbit.
- 30 July 2026
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
Feasibility study of shape memory dual-matrix composites for self-deployable structures
This study presents a lightweight and autonomous deployable structural concept that integrates origami-inspired geometries, dual-matrix composite architectures, and shape memory polymer (SMP) actuation. A shape memory dual-matrix composite reinforced with triaxial woven fabric and incorporating spatially distributed SMP and epoxy matrices is developed. The compliant SMP matrix is selectively placed along predefined folding lines to enable reversible deformation and thermally activated deployment, while the stiff epoxy matrix provides load-bearing capability in the deployed configuration. A unified constitutive model is formulated to describe the coupled thermomechanical and viscoelastic behavior of the SMP matrix and the mechanical response of the textile reinforcement. The thermomechanical properties of the proposed composite are characterized through uniaxial tensile tests, dynamic mechanical analysis, stress relaxation experiments, and shape recovery measurements. Based on the results, origami based self-deployable composite structures are fabricated and experimentally evaluated to demonstrate their deployment performance and structural feasibility.
- 30 July 2026
- Published by SAGE Publications in Journal of Intelligent Material Systems and Structures
Feasibility study of shape memory dual-matrix composites for self-deployable structures
This study presents a lightweight and autonomous deployable structural concept that integrates origami-inspired geometries, dual-matrix composite architectures, and shape memory polymer (SMP) actuation. A shape memory dual-matrix composite reinforced with triaxial woven fabric and incorporating spatially distributed SMP and epoxy matrices is developed. The compliant SMP matrix is selectively placed along predefined folding lines to enable reversible deformation and thermally activated deployment, while the stiff epoxy matrix provides load-bearing capability in the deployed configuration. A unified constitutive model is formulated to describe the coupled thermomechanical and viscoelastic behavior of the SMP matrix and the mechanical response of the textile reinforcement. The thermomechanical properties of the proposed composite are characterized through uniaxial tensile tests, dynamic mechanical analysis, stress relaxation experiments, and shape recovery measurements. Based on the results, origami based self-deployable composite structures are fabricated and experimentally evaluated to demonstrate their deployment performance and structural feasibility.
- Open Access
Numerical Study on Shape Recovery Behaviors of Shape Memory Polymer Composite Hinges Considering Hysteresis Effect
Shape memory polymer composite (SMPC) hinges have been researched as deployable structures in space missions due to their stable and controllable shape recovery behaviors. The elastic energy of the fabrics plays a dominant role in predicting the recovered shape of the hinges, as it strongly drives shape restoration. In this research, the shape recovery behaviors of SMPC hinges are numerically investigated by applying an equation that accounts for the hysteresis characteristics of the fabric reinforcement. The constitutive equation integrates the Mooney–Rivlin model, a viscoelastic, stored energy model, to characterize the hyperelastic properties varying with time, temperature, and shape recovery behaviors of the SMP matrix. Additionally, polynomial functions are introduced to represent the hysteresis effects and energy dissipation behavior of the fabrics. Since the elasticity of fabrics significantly affects the shape recovery of SMPCs, the developed constitutive equation enables accurate prediction of the recovered configuration. Finite element method analysis is performed based on this model and validated through comparison with experimental results. Finally, the constitutive equation is applied to investigate the shape memory response of SMPC hinges. The simulations present the significant design factors to increase the shape recovery ratio of the SMPC hinges.
Open AccessNumerical Study on Shape Recovery Behaviors of Shape Memory Polymer Composite Hinges Considering Hysteresis Effect
Shape memory polymer composite (SMPC) hinges have been researched as deployable structures in space missions due to their stable and controllable shape recovery behaviors. The elastic energy of the fabrics plays a dominant role in predicting the recovered shape of the hinges, as it strongly drives shape restoration. In this research, the shape recovery behaviors of SMPC hinges are numerically investigated by applying an equation that accounts for the hysteresis characteristics of the fabric reinforcement. The constitutive equation integrates the Mooney–Rivlin model, a viscoelastic, stored energy model, to characterize the hyperelastic properties varying with time, temperature, and shape recovery behaviors of the SMP matrix. Additionally, polynomial functions are introduced to represent the hysteresis effects and energy dissipation behavior of the fabrics. Since the elasticity of fabrics significantly affects the shape recovery of SMPCs, the developed constitutive equation enables accurate prediction of the recovered configuration. Finite element method analysis is performed based on this model and validated through comparison with experimental results. Finally, the constitutive equation is applied to investigate the shape memory response of SMPC hinges. The simulations present the significant design factors to increase the shape recovery ratio of the SMPC hinges.
- Open Access
Flexible Surface Reflector Antenna for Small Satellites
A novel deployable reflector antenna for small satellites has been designed, fabricated, and experimentally validated. The reflector utilizes a doubly curved flexible surface manufactured from a triaxially woven fabric-reinforced silicone (TWFS) composite. By leveraging high-strain composite materials, the design enables a highly compact stowed configuration while maintaining precise surface accuracy upon deployment. The deployment mechanism is proposed to accommodate a 0.6 m diameter parabolic reflector within a minimal stowed volume, optimizing space efficiency for satellite integration. To validate this concept, a prototype of the reflector antenna has been fabricated and demonstrated the feasibility and effectiveness of the proposed approach.
Open AccessFlexible Surface Reflector Antenna for Small Satellites
A novel deployable reflector antenna for small satellites has been designed, fabricated, and experimentally validated. The reflector utilizes a doubly curved flexible surface manufactured from a triaxially woven fabric-reinforced silicone (TWFS) composite. By leveraging high-strain composite materials, the design enables a highly compact stowed configuration while maintaining precise surface accuracy upon deployment. The deployment mechanism is proposed to accommodate a 0.6 m diameter parabolic reflector within a minimal stowed volume, optimizing space efficiency for satellite integration. To validate this concept, a prototype of the reflector antenna has been fabricated and demonstrated the feasibility and effectiveness of the proposed approach.
- Open Access
- 31 March 2025
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 36 (3) , 250-253
Design and Fabrication of an Reflector Antenna for Satellites Using Carbon Fiber Reinforced-Silicon (CFRS)
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- 31 March 2025
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 36 (3) , 250-253
Open AccessDesign and Fabrication of an Reflector Antenna for Satellites Using Carbon Fiber Reinforced-Silicon (CFRS)
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- Open Access
- 10 March 2025
- Published by MDPI AG in Preprints.org
Flexible Surface Reflector Antenna for Small Satellites
A novel deployable reflector antenna for small satellites has been designed, fabricated, and experimentally validated. The reflector utilizes a doubly curved flexible surface manufactured from a triaxially woven fabric-reinforced silicone (TWFS) composite. By leveraging high-strain composite materials, the design enables a highly compact stowed configuration while maintaining precise surface accuracy upon deployment. The deployment mechanism is proposed to accommodate a 0.6 m diameter parabolic reflector within a minimal stowed volume, optimizing space efficiency for satellite integration. To validate this concept, a prototype of the reflector antenna has been fabricated and demonstrated the feasibility and effectiveness of the proposed approach.
- 10 March 2025
- Published by MDPI AG in Preprints.org
Open AccessFlexible Surface Reflector Antenna for Small Satellites
A novel deployable reflector antenna for small satellites has been designed, fabricated, and experimentally validated. The reflector utilizes a doubly curved flexible surface manufactured from a triaxially woven fabric-reinforced silicone (TWFS) composite. By leveraging high-strain composite materials, the design enables a highly compact stowed configuration while maintaining precise surface accuracy upon deployment. The deployment mechanism is proposed to accommodate a 0.6 m diameter parabolic reflector within a minimal stowed volume, optimizing space efficiency for satellite integration. To validate this concept, a prototype of the reflector antenna has been fabricated and demonstrated the feasibility and effectiveness of the proposed approach.
- 11 December 2023
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 58 (2) , 145-165
A three-dimensional constitutive equation for shape memory polymer composites considering energy dissipation under single loading–unloading condition
Shape memory polymer composites (SMPCs), composed of shape memory polymers (SMPs) and fabrics, can recover their deformed shapes to initial configurations by changing temperature. The shape recovery energy of the SMPs and the elastic energy of the fabrics are regarded as key points to predict the restored configuration of the SMPCs. In this research, a three-dimensional constitutive equation for SMPCs is newly developed, considering the energy dissipation of fabrics under a single loading–unloading condition. The constitutive equation is derived from Mooney–Rivlin, viscoelastic, and stored strain energy models for SMPs, as well as polynomial functions for fabrics. The Mooney–Rivlin and viscoelastic models describe the time- and temperature-dependent hyperelastic properties, and the stored strain energy model can explain the shape recovery. The polynomial functions are newly proposed to take into account the dissipated energy of fabrics, such as residual deformation and hysteresis effect. Because the elastic energy of fabrics considerably influences the shape recovery of SMPCs, the proposed constitutive equation can accurately predict the recovered configuration. Analyses of SMPCs are conducted using the finite element method and validated by comparing them with the results obtained from experiments. The constitutive equation is used to analyze the shape recovery behaviors of an SMPC skin. The skin can be largely stretched, and the deformed shape can be restored to its initial shape by applying electricity. The SMPC skin is applied to a morphing flap, and its shape-changing behaviors are demonstrated experimentally.
- 11 December 2023
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 58 (2) , 145-165
A three-dimensional constitutive equation for shape memory polymer composites considering energy dissipation under single loading–unloading condition
Shape memory polymer composites (SMPCs), composed of shape memory polymers (SMPs) and fabrics, can recover their deformed shapes to initial configurations by changing temperature. The shape recovery energy of the SMPs and the elastic energy of the fabrics are regarded as key points to predict the restored configuration of the SMPCs. In this research, a three-dimensional constitutive equation for SMPCs is newly developed, considering the energy dissipation of fabrics under a single loading–unloading condition. The constitutive equation is derived from Mooney–Rivlin, viscoelastic, and stored strain energy models for SMPs, as well as polynomial functions for fabrics. The Mooney–Rivlin and viscoelastic models describe the time- and temperature-dependent hyperelastic properties, and the stored strain energy model can explain the shape recovery. The polynomial functions are newly proposed to take into account the dissipated energy of fabrics, such as residual deformation and hysteresis effect. Because the elastic energy of fabrics considerably influences the shape recovery of SMPCs, the proposed constitutive equation can accurately predict the recovered configuration. Analyses of SMPCs are conducted using the finite element method and validated by comparing them with the results obtained from experiments. The constitutive equation is used to analyze the shape recovery behaviors of an SMPC skin. The skin can be largely stretched, and the deformed shape can be restored to its initial shape by applying electricity. The SMPC skin is applied to a morphing flap, and its shape-changing behaviors are demonstrated experimentally.
- 24 July 2022
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 31 (6) , 669-682
Damage prediction of thick composite laminates subjected to low-velocity impact loads
Experimental and numerical studies have been carried out to predict the behavior of composite laminates under low-velocity impact loads. Numerical models were built based on shell elements in order to simulate it efficiently. A strain-based failure theory was employed to predict the damaged area of laminates using a user-defined subroutine. Drop-weight impact tests were performed for verifying the analysis results of the low-velocity impact. The damaged areas were inspected using ultrasonic C-scans, and three types of thick composite laminates were examined. The impactor velocity was measured at time before and after contact with the target. Finally, the proposed numerical model with the failure theory was verified in that it well predicted the impact damage of the three composite laminates chosen for this study.
- 24 July 2022
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 31 (6) , 669-682
Damage prediction of thick composite laminates subjected to low-velocity impact loads
Experimental and numerical studies have been carried out to predict the behavior of composite laminates under low-velocity impact loads. Numerical models were built based on shell elements in order to simulate it efficiently. A strain-based failure theory was employed to predict the damaged area of laminates using a user-defined subroutine. Drop-weight impact tests were performed for verifying the analysis results of the low-velocity impact. The damaged areas were inspected using ultrasonic C-scans, and three types of thick composite laminates were examined. The impactor velocity was measured at time before and after contact with the target. Finally, the proposed numerical model with the failure theory was verified in that it well predicted the impact damage of the three composite laminates chosen for this study.
- Open Access
- 30 September 2020
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 31 (9) , 758-769
Design and Implementation of Lightweight Antenna for Small Satellite SAR with Feeder Strut
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- 30 September 2020
- Published by Korean Institute of Electromagnetic Engineering and Science in The Journal of Korean Institute of Electromagnetic Engineering and Science
- Vol. 31 (9) , 758-769
Open AccessDesign and Implementation of Lightweight Antenna for Small Satellite SAR with Feeder Strut
한국전자파학회논문지 (The Journal of Korean Institute of Electromagnetic Engineering and Science)
- 2 March 2020
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 29 (3) , 301-316
Failure analysis of laminated composites subjected to flexural loadings
The failure of laminated composites under out-of-plane loadings is experimentally and numerically investigated. For flexure failure prediction, a modified failure criterion is proposed. A progressive failure algorithm is developed for numerical analyses. In experiments, quasi–isotropic and cross-ply laminated composites are fabricated by using unidirectional carbon fiber and glass fabric prepregs. Three-point bending test is performed and the accuracy of the failure algorithm is verified with experimental results. In addition, the flexure failure behaviors are compared with those of a commercial finite element analysis program using the other failure criteria such as maximum strain, maximum stress, and Tasi–Wu.
- 2 March 2020
- Published by Taylor & Francis in Advanced Composite Materials
- Vol. 29 (3) , 301-316
Failure analysis of laminated composites subjected to flexural loadings
The failure of laminated composites under out-of-plane loadings is experimentally and numerically investigated. For flexure failure prediction, a modified failure criterion is proposed. A progressive failure algorithm is developed for numerical analyses. In experiments, quasi–isotropic and cross-ply laminated composites are fabricated by using unidirectional carbon fiber and glass fabric prepregs. Three-point bending test is performed and the accuracy of the failure algorithm is verified with experimental results. In addition, the flexure failure behaviors are compared with those of a commercial finite element analysis program using the other failure criteria such as maximum strain, maximum stress, and Tasi–Wu.