Xiang Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xiang Zhou has a total of 63 co-authors. Here are the top co-authors by number of shared publications:
- Laili Wang
State Key Laboratory of Electrical Insulation and Power Equipment, Xian Jiaotong University, Xian, China
9 shared publications - Yan-Fei Liu
Department of Electrical and Computer Engineering, Queens University, Kingston, ON, Canada
6 shared publications - Zihao Song
State Key Laboratory of Electrical Insulation and Power Equipment, Xian Jiaotong University, Xian, China
4 shared publications - Huan Luo
Sichuan University
3 shared publications - Jianping Xu
Southwest Jiaotong University
3 shared publications Shi Chen
College of Electrical Engineering, Sichuan University, Chengdu, China
3 shared publications
Latest Publications
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (10) , 14421-14433
Maximum Efficiency Point Tracking Technology for Dual-Bridge Series Resonant Converter
Typically, the efficiency of a power electronic converter follows a parabolic trend, rising initially and then decreasing as the load current increases. To enhance efficiency in the ascending segment (left of the peak) of the quasi-parabolic efficiency curve, this article proposes a maximum efficiency point tracking (MEPT) technology that elevates the converter’s efficiency within this ascending segment to the maximum-efficiency point. The proposed MEPT technique is investigated using a dual-bridge series resonant converter (DBSRC) under extended-phase-shift and variable-frequency control as a representative case. By combining pulse skipping modulation with optimal trajectory control, the operating current during the pulse-retained cycles is regulated to match the load current corresponding to the maximum-efficiency point. As a result, the converter can operate equivalently at the maximum-efficiency point. In addition, the internal phase-shift angle, external phase-shift angle, and switching frequency remain fixed when the load current varies. Output regulation is achieved solely by adjusting the pulse-skipped ratio. This feature significantly reduces the control complexity compared with conventional multi-degree-of-freedom control schemes. Finally, a DBSRC prototype with input voltage range of 360–560 V and output voltage of 36.5 V is built to validate the proposed MEPT technology and the theoretical analysis.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 73 (10) , 14421-14433
Maximum Efficiency Point Tracking Technology for Dual-Bridge Series Resonant Converter
Typically, the efficiency of a power electronic converter follows a parabolic trend, rising initially and then decreasing as the load current increases. To enhance efficiency in the ascending segment (left of the peak) of the quasi-parabolic efficiency curve, this article proposes a maximum efficiency point tracking (MEPT) technology that elevates the converter’s efficiency within this ascending segment to the maximum-efficiency point. The proposed MEPT technique is investigated using a dual-bridge series resonant converter (DBSRC) under extended-phase-shift and variable-frequency control as a representative case. By combining pulse skipping modulation with optimal trajectory control, the operating current during the pulse-retained cycles is regulated to match the load current corresponding to the maximum-efficiency point. As a result, the converter can operate equivalently at the maximum-efficiency point. In addition, the internal phase-shift angle, external phase-shift angle, and switching frequency remain fixed when the load current varies. Output regulation is achieved solely by adjusting the pulse-skipped ratio. This feature significantly reduces the control complexity compared with conventional multi-degree-of-freedom control schemes. Finally, a DBSRC prototype with input voltage range of 360–560 V and output voltage of 36.5 V is built to validate the proposed MEPT technology and the theoretical analysis.
- 28 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (9) , 15948-15963
A Hybrid Control Strategy of Dual-Bridge Series Resonant Converter for Soft-Switching Range Extension and Backflow Power Reduction
Dual-bridge series resonant converter (DBSRC), featuring high efficiency and high power density, is widely applied in scenarios such as electric vehicle (EV) chargers, etc. However, under light-load or non-unity voltage gain conditions, DBSRCs with single-phase-shift variable-frequency (SPS-VF) modulation require an extremely high switching frequency to ensure zero-voltage-switching (ZVS) for all switches and suppress backflow power. To address this issue, this paper proposes a hybrid control strategy that integrates pulse skipping modulation (PSM) into the SPS-VF framework. By increasing the operating current during the pulse-retained cycles, PSM extends the ZVS region and suppresses backflow power. Within a relatively low switching frequency range, the proposed strategy can simultaneously achieve ZVS turn-on for all switches and zero-current-switching (ZCS) turn-off for the secondary switches, while also ensuring zero backflow power on the output capacitor. Finally, a DBSRC prototype with input voltage range of 360–560 V and output voltage of 36.5 V is built to validate the proposed hybrid control strategy.
- 28 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (9) , 15948-15963
A Hybrid Control Strategy of Dual-Bridge Series Resonant Converter for Soft-Switching Range Extension and Backflow Power Reduction
Dual-bridge series resonant converter (DBSRC), featuring high efficiency and high power density, is widely applied in scenarios such as electric vehicle (EV) chargers, etc. However, under light-load or non-unity voltage gain conditions, DBSRCs with single-phase-shift variable-frequency (SPS-VF) modulation require an extremely high switching frequency to ensure zero-voltage-switching (ZVS) for all switches and suppress backflow power. To address this issue, this paper proposes a hybrid control strategy that integrates pulse skipping modulation (PSM) into the SPS-VF framework. By increasing the operating current during the pulse-retained cycles, PSM extends the ZVS region and suppresses backflow power. Within a relatively low switching frequency range, the proposed strategy can simultaneously achieve ZVS turn-on for all switches and zero-current-switching (ZCS) turn-off for the secondary switches, while also ensuring zero backflow power on the output capacitor. Finally, a DBSRC prototype with input voltage range of 360–560 V and output voltage of 36.5 V is built to validate the proposed hybrid control strategy.
- 17 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (8) , 12639-12654
A Control Strategy With Pulse Skipping and Optimal Trajectory for Efficiency Improvement of Dual-Bridge Series Resonant Converter Under Light-Load or Non-Unity-Gain Conditions
Dual-bridge series resonant converter (DBSRC) is widely employed in high-voltage and high-power applications such as electric vehicle (EV) chargers, power conversion systems (PCS), etc,. However, under light-load or non-unity voltage gain conditions, the DBSRC with traditional single-phase-shift (SPS) modulation exhibits a very small external phase-shift angle. This leads to significant backflow power, which increases both the root-mean-square (RMS) value of the resonant current and the switch turn-off current, consequently lowering the efficiency. To address this issue, a novel control strategy combining pulse skipping modulation (PSM) with optimal trajectory control (OTC) is proposed in this paper. PSM operates in a periodic pattern: within every C switching cycles, only the first E cycles (E < C) are retained for energy transfer, while the driving signals in the rest of (C- E) cycles are skipped. This increases the energy transferred during each pulse-retained cycle, enlarges the external phase-shift angle, and consequently reduces backflow power. Moreover, switching and driving losses are completely eliminated during the pulse-skipped cycles, further improving efficiency. In order to suppress the transient oscillations induced by PSM,OTCisemployed to force the converter to enter steady state trajectory within the first pulse cycle among E consecutive driving signals. Theoretical analysis shows that the proposed control strategy effectively reduces the losses. Finally, a prototype with 200 V input and 12–24 V output is built to verify the proposed strategy. Experimental results demonstrate that, compared to the traditional SPS scheme, the proposed control strategy improves the prototype's efficiency by at least 8% under non-unity gain and light-load conditions.
- 17 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (8) , 12639-12654
A Control Strategy With Pulse Skipping and Optimal Trajectory for Efficiency Improvement of Dual-Bridge Series Resonant Converter Under Light-Load or Non-Unity-Gain Conditions
Dual-bridge series resonant converter (DBSRC) is widely employed in high-voltage and high-power applications such as electric vehicle (EV) chargers, power conversion systems (PCS), etc,. However, under light-load or non-unity voltage gain conditions, the DBSRC with traditional single-phase-shift (SPS) modulation exhibits a very small external phase-shift angle. This leads to significant backflow power, which increases both the root-mean-square (RMS) value of the resonant current and the switch turn-off current, consequently lowering the efficiency. To address this issue, a novel control strategy combining pulse skipping modulation (PSM) with optimal trajectory control (OTC) is proposed in this paper. PSM operates in a periodic pattern: within every C switching cycles, only the first E cycles (E < C) are retained for energy transfer, while the driving signals in the rest of (C- E) cycles are skipped. This increases the energy transferred during each pulse-retained cycle, enlarges the external phase-shift angle, and consequently reduces backflow power. Moreover, switching and driving losses are completely eliminated during the pulse-skipped cycles, further improving efficiency. In order to suppress the transient oscillations induced by PSM,OTCisemployed to force the converter to enter steady state trajectory within the first pulse cycle among E consecutive driving signals. Theoretical analysis shows that the proposed control strategy effectively reduces the losses. Finally, a prototype with 200 V input and 12–24 V output is built to verify the proposed strategy. Experimental results demonstrate that, compared to the traditional SPS scheme, the proposed control strategy improves the prototype's efficiency by at least 8% under non-unity gain and light-load conditions.
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- p. 1
Investigation on the Transient Electro-Thermal Characteristics and Overcurrent Capability of Multichip Parallel SiC MOSFET Modules under Pulsed High Current Excitation
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- p. 1
Investigation on the Transient Electro-Thermal Characteristics and Overcurrent Capability of Multichip Parallel SiC MOSFET Modules under Pulsed High Current Excitation
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (4) , 8768-8783
Wide Voltage-Regulation Range Synchronous-Rectifier LLC Converter With Novel Operation Modes
Traditionally, the energy feedback in synchronous rectifier (SR) LLC converter was once considered to only have the ability to reduce the voltage gain. In this article, a kind of special energy feedback caused by the novel operation modes of LLC resonant converter is proposed for improving voltage gain. Compared to the P, O, and N stages in conventional LLC converter, stage F is built by controlling the turn-on early time of the SR. By using the proposed operation modes, not only zero-voltage switching (ZVS) of both the primary-side and secondary-side switches is achieved, but the voltage gain of the LLC converter can be increased significantly with a narrow switching frequency range and a smaller magnetizing inductance circulating current. In addition, the proposed operation modes are simple and easy to be utilized in full bridge, half bridge, and so on; all kinds of LLC converters thus can form a new general control strategy of the SR LLC. Finally, a 100-W half-bridge SR LLC dc-dc converter prototype with a wide voltage-regulation range is implemented to validate the proposed operation modes and the theoretical analysis.
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 11 (4) , 8768-8783
Wide Voltage-Regulation Range Synchronous-Rectifier LLC Converter With Novel Operation Modes
Traditionally, the energy feedback in synchronous rectifier (SR) LLC converter was once considered to only have the ability to reduce the voltage gain. In this article, a kind of special energy feedback caused by the novel operation modes of LLC resonant converter is proposed for improving voltage gain. Compared to the P, O, and N stages in conventional LLC converter, stage F is built by controlling the turn-on early time of the SR. By using the proposed operation modes, not only zero-voltage switching (ZVS) of both the primary-side and secondary-side switches is achieved, but the voltage gain of the LLC converter can be increased significantly with a narrow switching frequency range and a smaller magnetizing inductance circulating current. In addition, the proposed operation modes are simple and easy to be utilized in full bridge, half bridge, and so on; all kinds of LLC converters thus can form a new general control strategy of the SR LLC. Finally, a 100-W half-bridge SR LLC dc-dc converter prototype with a wide voltage-regulation range is implemented to validate the proposed operation modes and the theoretical analysis.
- Open Access
- 12 November 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (16) , 2852-2860
A synchronization method based on current orthogonal decomposition considering harmonic components for wireless power transfer system
In order to improve the wireless power transfer (WPT) system, an active rectifier is commonly used. Synchronization technology is critical for active rectifier. The traditional synchronization method based on zero‐crossing detection (ZCD) is unstable and not suitable for the case with lots of harmonic component in the resonant current. Here, a new synchronization method with harmonic compensation is proposed for the WPT system without the ZCD of the resonant current. A mathematical model is built to analyse and compensate the impact caused by the harmonic on phase angle. Therefore, the proposed method can be applied to the high‐order resonant network like LCC compensated topology where the harmonic component is rich in the resonant current. For verifying the proposed synchronization method, a laboratory prototype is built. The experimental results prove that the system can operate stably with parameter perturbation and different load. The peak transfer efficiency of the system can achieve the 94.5%.
- 12 November 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (16) , 2852-2860
Open AccessA synchronization method based on current orthogonal decomposition considering harmonic components for wireless power transfer system
In order to improve the wireless power transfer (WPT) system, an active rectifier is commonly used. Synchronization technology is critical for active rectifier. The traditional synchronization method based on zero‐crossing detection (ZCD) is unstable and not suitable for the case with lots of harmonic component in the resonant current. Here, a new synchronization method with harmonic compensation is proposed for the WPT system without the ZCD of the resonant current. A mathematical model is built to analyse and compensate the impact caused by the harmonic on phase angle. Therefore, the proposed method can be applied to the high‐order resonant network like LCC compensated topology where the harmonic component is rich in the resonant current. For verifying the proposed synchronization method, a laboratory prototype is built. The experimental results prove that the system can operate stably with parameter perturbation and different load. The peak transfer efficiency of the system can achieve the 94.5%.
- 23 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (5) , 5135-5154
Hybrid Control Strategy for Single-Stage Interleaved Totem-Pole LLC AC–DC Converter With Input and Output Power Decoupling
This paper proposes a hybrid control strategy for single-stage interleaved totem-pole LLC AC-DC converter. Since the totem-pole power factor correction (PFC) front-cell provides bi-direction inductor current, this converter is restricted by operating in continuous conduction mode (CCM) or critical conduction mode (CRM). The traditional control strategy shows variable duty cycle of the resonant tank voltage to the instantaneous AC input voltage. Therefore, the line-frequency variation from the AC input-end will be easily interfaced to the load, and brings a large fluctuation of output voltage. To tackle this issue, this paper proposed a novel control strategy that utilizes pulse width modulation (PWM) to shape the input current, and pulse frequency modulation (PFM) to regulate the output voltage. As a positive consequence, the large output voltage ripple brought by the variation of duty cycle for traditional PWM-based control is therefore effectively compensated by the variation of switching frequency, and the power decoupling between the AC pulse input power and constant DC output power is achieved. Numerical-based calculation method is utilized to develop the time-domain analysis of the converter, and a 500W/150V experimental prototype has been built to verify the proposed control strategy and theoretical analysis.
- 23 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (5) , 5135-5154
Hybrid Control Strategy for Single-Stage Interleaved Totem-Pole LLC AC–DC Converter With Input and Output Power Decoupling
This paper proposes a hybrid control strategy for single-stage interleaved totem-pole LLC AC-DC converter. Since the totem-pole power factor correction (PFC) front-cell provides bi-direction inductor current, this converter is restricted by operating in continuous conduction mode (CCM) or critical conduction mode (CRM). The traditional control strategy shows variable duty cycle of the resonant tank voltage to the instantaneous AC input voltage. Therefore, the line-frequency variation from the AC input-end will be easily interfaced to the load, and brings a large fluctuation of output voltage. To tackle this issue, this paper proposed a novel control strategy that utilizes pulse width modulation (PWM) to shape the input current, and pulse frequency modulation (PFM) to regulate the output voltage. As a positive consequence, the large output voltage ripple brought by the variation of duty cycle for traditional PWM-based control is therefore effectively compensated by the variation of switching frequency, and the power decoupling between the AC pulse input power and constant DC output power is achieved. Numerical-based calculation method is utilized to develop the time-domain analysis of the converter, and a 500W/150V experimental prototype has been built to verify the proposed control strategy and theoretical analysis.
- Open Access
- 26 June 2023
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (10) , 1176-1188
Analysis and design of synchronous‐rectified LLC DC–DC converter for LDC of electric vehicles
In electric vehicles (EVs), the low voltage dc‐dc converter (LDC) with synchronous rectifier switches (SRs) can be used to reduce conduction loss caused by the high load current and improve the efficiency. Therefore, it is important to design a proper turn‐on time of SRs. As a popular driving strategy for the SRs, the drain–source voltage across the SRs is sensed to generate the gate driving signal. However, when LLC dc–dc converter operates at O mode, there will be a voltage ringing across the SRs. If the ringing voltage reaches to the threshold voltage − V th,on , it would make SRs turn‐on early and results in abnormally working of the converter. The novelty and contribution of this paper lie in: (1) elaborating on the voltage ringing across the SRs, (2) the accurate ringing model is established during O mode, and (3) a simple, lossless, and low‐cost filter circuit is used to solve the negative effect of the ringing voltage for LLC converter at high load current. A 1.26 kW experimental prototype with ≈250–430 V wide input voltage and ≈9–16 V wide output voltage is implemented, 96.7% peak efficiency and 96% full load efficiency are achieved with a 3.12 kW/L power density. The theoretical analysis has been validated by the simulated and experimental results, and the SR LLC dc–dc converter with the SR works efficiently and reliably with the proposed solution at a high load current.
- 26 June 2023
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (10) , 1176-1188
Open AccessAnalysis and design of synchronous‐rectified LLC DC–DC converter for LDC of electric vehicles
In electric vehicles (EVs), the low voltage dc‐dc converter (LDC) with synchronous rectifier switches (SRs) can be used to reduce conduction loss caused by the high load current and improve the efficiency. Therefore, it is important to design a proper turn‐on time of SRs. As a popular driving strategy for the SRs, the drain–source voltage across the SRs is sensed to generate the gate driving signal. However, when LLC dc–dc converter operates at O mode, there will be a voltage ringing across the SRs. If the ringing voltage reaches to the threshold voltage − V th,on , it would make SRs turn‐on early and results in abnormally working of the converter. The novelty and contribution of this paper lie in: (1) elaborating on the voltage ringing across the SRs, (2) the accurate ringing model is established during O mode, and (3) a simple, lossless, and low‐cost filter circuit is used to solve the negative effect of the ringing voltage for LLC converter at high load current. A 1.26 kW experimental prototype with ≈250–430 V wide input voltage and ≈9–16 V wide output voltage is implemented, 96.7% peak efficiency and 96% full load efficiency are achieved with a 3.12 kW/L power density. The theoretical analysis has been validated by the simulated and experimental results, and the SR LLC dc–dc converter with the SR works efficiently and reliably with the proposed solution at a high load current.
- 14 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (5) , 4883-4895
Multioutput Wireless Charger for Drone Swarms With Reduced Switch Requirements and Independent Regulation Capability
This article develops a cost-effective and efficient wireless charger with multiple outputs based on the newly proposed H3-bridge inverter, which has the benefits of reduced switch requirements and independent regulation capability. The output power of each channel is regulated by asymmetric duty cycle control. With the help of the auxiliary LC branch, soft switching is ensured in spite of load variations. The sequential logic of driver signals is analyzed in detail to explore independent regulation characteristics. For arbitrary 2 n (or 2 n +1) outputs, the total number of required switches is only 3 n (or 3 n +2), and the voltage stress of switches is the input voltage, which can reduce switch requirements. Simulation and experimental results are in good agreement with each other, proving that the proposed wireless charger is a feasible solution for drone swarms.
- 14 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 71 (5) , 4883-4895
Multioutput Wireless Charger for Drone Swarms With Reduced Switch Requirements and Independent Regulation Capability
This article develops a cost-effective and efficient wireless charger with multiple outputs based on the newly proposed H3-bridge inverter, which has the benefits of reduced switch requirements and independent regulation capability. The output power of each channel is regulated by asymmetric duty cycle control. With the help of the auxiliary LC branch, soft switching is ensured in spite of load variations. The sequential logic of driver signals is analyzed in detail to explore independent regulation characteristics. For arbitrary 2 n (or 2 n +1) outputs, the total number of required switches is only 3 n (or 3 n +2), and the voltage stress of switches is the input voltage, which can reduce switch requirements. Simulation and experimental results are in good agreement with each other, proving that the proposed wireless charger is a feasible solution for drone swarms.
- 23 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 70 (9) , 3529-3533
Soft-Switching Resonant DC Transformer for Class-D Switching Amplifier With Symmetric Bipolar Outputs
In this letter, soft-switching resonant DC transformer (DCX) for the class-D switching amplifier with the symmetric bipolar outputs is proposed. The proposed DCX consists of a single transformer primary inverter circuit and two transformer secondary dual series resonant half-bridge rectifier circuits, which reduces the voltage stress of the rectifier diodes. In the proposed DCX, the duty cycle of the primary inverter circuit is 0.5, and the symmetric bipolar output voltage gains only depend on the transformer. By dual series resonance between the leakage inductance and the output resonant capacitors, ZVS turn-on of switches and ZCS turn-off of the diodes can be achieved, which improves the overall efficiency. The characteristic of the DCX is elaborated and analyzed in this letter. Finally, a 60 W prototype is established and the experimental verified the theoretical analysis of the proposed DCX.
- 23 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 70 (9) , 3529-3533
Soft-Switching Resonant DC Transformer for Class-D Switching Amplifier With Symmetric Bipolar Outputs
In this letter, soft-switching resonant DC transformer (DCX) for the class-D switching amplifier with the symmetric bipolar outputs is proposed. The proposed DCX consists of a single transformer primary inverter circuit and two transformer secondary dual series resonant half-bridge rectifier circuits, which reduces the voltage stress of the rectifier diodes. In the proposed DCX, the duty cycle of the primary inverter circuit is 0.5, and the symmetric bipolar output voltage gains only depend on the transformer. By dual series resonance between the leakage inductance and the output resonant capacitors, ZVS turn-on of switches and ZCS turn-off of the diodes can be achieved, which improves the overall efficiency. The characteristic of the DCX is elaborated and analyzed in this letter. Finally, a 60 W prototype is established and the experimental verified the theoretical analysis of the proposed DCX.