Kantha Lankatilake
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kantha Lankatilake has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Anurudda Karunarathna Karunarathna
Department of Agricultural Engineering, Faculty of Agriculture, University of Peradeniya, Peradeniya 20400, Sri Lanka
1 shared publication C. G. Uragoda
†Central Chest ClinicColombo, Sri Lanka
1 shared publicationD. B. D. L. Samaranayake
Department of Community Medicine, Faculty of Medicine, University of Colombo, Sri Lanka
1 shared publicationDulani Samaranayake
1 shared publication- K. R. M. Chandrathilaka
Department of Allied Health Sciences, Faculty of Medicine, University of Colombo, Sri Lanka
1 shared publication Kasun Piyathunga
1 shared publication
Latest Publications
- Open Access
- 23 July 2018
- Published by Medip Academy in International Journal Of Community Medicine And Public Health
- Vol. 5 (8) , 3257-3264
Work environment of automated and non-automated rice mills in Amapara district, Sri Lanka
Background: Paddy cultivation is a major occupation in informal sector in Sri Lanka. In 2014, contribution of the agricultural activities to the country’s annual GDP was 9.9% of which, contribution by paddy was 11.3%. The objective of the current study was to describe the work environment in rice mills with respect to dust, humidity and thermal condition, ventilation and illumination.Methods: A cross sectional study in 107 randomly selected rice mills was carried out in Ampara district in Sri Lanka. Standardized measurements were carried out to assess internal work environment of the mills.Results: Milling activities showed a seasonal variation. The majority of the mills (95.3%) manufactured raw rice only. Other than the basic characteristics, both automated (AMs) and non-automated mills (NAMs) showed common features. All rice mills exceeded the threshold limit values for total (520.04 mg/m3, SD=191.86 mg/m3) and respirable dust (48.14 mg/m3, SD=9.4 mg/m3). Mean daytime indoor relative humidity in the majority of the mills (n=102, 95.3%) was within the accepted upper limit. In most of the mills, ventilation (n=84, 78.5%) and illumination in polishing/packing area (n=60, 56.1%) was satisfactory while in dehusking/paddy inlet area (n=96, 89.7%), illumination was below the limits.Conclusions: Work environment in both the AMs and NAMs in Ampara district presented with poor work standards compared to the required guidelines.
- 23 July 2018
- Published by Medip Academy in International Journal Of Community Medicine And Public Health
- Vol. 5 (8) , 3257-3264
Open AccessWork environment of automated and non-automated rice mills in Amapara district, Sri Lanka
Background: Paddy cultivation is a major occupation in informal sector in Sri Lanka. In 2014, contribution of the agricultural activities to the country’s annual GDP was 9.9% of which, contribution by paddy was 11.3%. The objective of the current study was to describe the work environment in rice mills with respect to dust, humidity and thermal condition, ventilation and illumination.Methods: A cross sectional study in 107 randomly selected rice mills was carried out in Ampara district in Sri Lanka. Standardized measurements were carried out to assess internal work environment of the mills.Results: Milling activities showed a seasonal variation. The majority of the mills (95.3%) manufactured raw rice only. Other than the basic characteristics, both automated (AMs) and non-automated mills (NAMs) showed common features. All rice mills exceeded the threshold limit values for total (520.04 mg/m3, SD=191.86 mg/m3) and respirable dust (48.14 mg/m3, SD=9.4 mg/m3). Mean daytime indoor relative humidity in the majority of the mills (n=102, 95.3%) was within the accepted upper limit. In most of the mills, ventilation (n=84, 78.5%) and illumination in polishing/packing area (n=60, 56.1%) was satisfactory while in dehusking/paddy inlet area (n=96, 89.7%), illumination was below the limits.Conclusions: Work environment in both the AMs and NAMs in Ampara district presented with poor work standards compared to the required guidelines.
- 1 June 2012
- Published by Taylor & Francis in International Journal of Occupational and Environmental Health
- Vol. 18 (2) , 110-115
Exposure to polychlorinated biphenyls (PCBs) among welders in Sri Lanka
Polychlorinated biphenyls (PCBs) are a group of persistent organic pollutants with the ability to cause adverse impacts on human health and the environment. This study describes the indiscriminate use of PCB-contaminated transformer oil as a coolant in informal welding shops in Kalutara, Sri Lanka. Sixty-three welders, one each from a convenience sample of 63 welding workshops participated in the study. We administered a questionnaire and observed work practices. Sixty-two (98%) workplaces used transformer oil as the coolant in the welding equipment, 60 (95%) claiming that it was the only one available. Sixty-two (98%) did not use any protective measures when refilling coolant oil, while none of them safely disposed of the empty coolant oil containers. Only four (6%) were aware of the possible health effects of PCB-contaminated coolant oil. Health and safety measures in the work places studied were very poor. Coolant oil samples from a sub-sample of 30 welding workshops were tested for PCBs; 19 (63%) were positive. PCB-contaminated coolant oil is widely used by the welders in Kalutara without adequate precautions or safety measures.
- 1 June 2012
- Published by Taylor & Francis in International Journal of Occupational and Environmental Health
- Vol. 18 (2) , 110-115
Exposure to polychlorinated biphenyls (PCBs) among welders in Sri Lanka
Polychlorinated biphenyls (PCBs) are a group of persistent organic pollutants with the ability to cause adverse impacts on human health and the environment. This study describes the indiscriminate use of PCB-contaminated transformer oil as a coolant in informal welding shops in Kalutara, Sri Lanka. Sixty-three welders, one each from a convenience sample of 63 welding workshops participated in the study. We administered a questionnaire and observed work practices. Sixty-two (98%) workplaces used transformer oil as the coolant in the welding equipment, 60 (95%) claiming that it was the only one available. Sixty-two (98%) did not use any protective measures when refilling coolant oil, while none of them safely disposed of the empty coolant oil containers. Only four (6%) were aware of the possible health effects of PCB-contaminated coolant oil. Health and safety measures in the work places studied were very poor. Coolant oil samples from a sub-sample of 30 welding workshops were tested for PCBs; 19 (63%) were positive. PCB-contaminated coolant oil is widely used by the welders in Kalutara without adequate precautions or safety measures.
- 1 September 1993
- Published by Oxford University Press (OUP) in Occupational Medicine
- Vol. 43 (3) , 139-142
Respiratory function in chilli grinders
The active principle of chilli is capsaicin which when inhaled induces cough and transient increase in airway resistance through selective stimulation of sensory nerves in the airway. The present study was aimed at determining whether workers exposed to chilli dust showed ventilatory changes as in the pharmacological model. Twenty-five men with an average age of 28.5 years employed in five chilli grinding factories in Sri Lanka for an average of 6.6 years (range 3 months to 20 years) were clinically examined. Their ventilatory measurements were recorded before and after a Monday workshift. A control group was similarly examined. Dust levels in the respective chilli grinding factories were monitored. Fifteen men (60 per cent) had initial symptoms including cough on recruitment, but these passed off in 3 weeks to 6 months. There was no statistically significant across-shift change in ventilatory indices in chilli grinders when compared to the controls, nor was there a significant difference in the pre-shift measurements in the two groups. It is concluded that the airway resistance that occurs in the pharmacological model is too fleeting, if present in chilli grinders, to be recorded under ordinary conditions.
- 1 September 1993
- Published by Oxford University Press (OUP) in Occupational Medicine
- Vol. 43 (3) , 139-142
Respiratory function in chilli grinders
The active principle of chilli is capsaicin which when inhaled induces cough and transient increase in airway resistance through selective stimulation of sensory nerves in the airway. The present study was aimed at determining whether workers exposed to chilli dust showed ventilatory changes as in the pharmacological model. Twenty-five men with an average age of 28.5 years employed in five chilli grinding factories in Sri Lanka for an average of 6.6 years (range 3 months to 20 years) were clinically examined. Their ventilatory measurements were recorded before and after a Monday workshift. A control group was similarly examined. Dust levels in the respective chilli grinding factories were monitored. Fifteen men (60 per cent) had initial symptoms including cough on recruitment, but these passed off in 3 weeks to 6 months. There was no statistically significant across-shift change in ventilatory indices in chilli grinders when compared to the controls, nor was there a significant difference in the pre-shift measurements in the two groups. It is concluded that the airway resistance that occurs in the pharmacological model is too fleeting, if present in chilli grinders, to be recorded under ordinary conditions.
- 1 September 1990
- Vol. 35 (3) , 109-17
A survey of the thermal environment, sound and illuminance in an iron and a steel foundry and related health effects.
The thermal environment and the workers' physiological response to heat were monitored throughout the casting process in two foundries. Of the 86 thermal observations in the iron foundry, 25 (29%) exceeded the heat stress index set by Occupational Safety and Health Administration (OSHA) advisory committee in 1974. In the steel foundry during a steel casting the environmental thermal measurements remained above the standard. The workers' physiological indices of heat strain as measured by pulse rate and body temperature rarely showed excursions above limits recommended by World Health Organization (WHO) in 1969. The environmental noise levels exceeded the standard in certain foundry operations. A significant hearing threshold shift was observed at 4 kHz among the foundry workers when compared with non-exposed controls. The illuminance in both foundries was below values recommended by the illuminating Engineering Society, in 1977. The prevalence of lens and corneal opacities among workers in the iron foundry was 32.5% and 30.0% respectively, which was significantly higher than that of the workers in the steel foundry and non-exposed controls.
- 1 September 1990
- Vol. 35 (3) , 109-17
A survey of the thermal environment, sound and illuminance in an iron and a steel foundry and related health effects.
The thermal environment and the workers' physiological response to heat were monitored throughout the casting process in two foundries. Of the 86 thermal observations in the iron foundry, 25 (29%) exceeded the heat stress index set by Occupational Safety and Health Administration (OSHA) advisory committee in 1974. In the steel foundry during a steel casting the environmental thermal measurements remained above the standard. The workers' physiological indices of heat strain as measured by pulse rate and body temperature rarely showed excursions above limits recommended by World Health Organization (WHO) in 1969. The environmental noise levels exceeded the standard in certain foundry operations. A significant hearing threshold shift was observed at 4 kHz among the foundry workers when compared with non-exposed controls. The illuminance in both foundries was below values recommended by the illuminating Engineering Society, in 1977. The prevalence of lens and corneal opacities among workers in the iron foundry was 32.5% and 30.0% respectively, which was significantly higher than that of the workers in the steel foundry and non-exposed controls.