Chuwen Guo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chuwen Guo has a total of 61 co-authors. Here are the top co-authors by number of shared publications:
Fengchao Wang
School of Electrical and Power Engineering, China University of Mining and Technology, Xuzhou, People’s Republic of China
8 shared publicationsChiheng Qiang
School of Low-carbon Energy and Power Engineering, China University of Mining and Technology, Xuzhou, People’s Republic of China
5 shared publicationsDachuan Feng
School of Electrical and Power Engineering, China University of Mining and Technology, Xuzhou, People’s Republic of China
4 shared publications- Fengchao Wang
School of Low-carbon Energy and Power Engineering, China University of Mining and Technology, Xuzhou 221116, China
3 shared publications Kaining Yang
School of Low-carbon Energy and Power Engineering, China University of Mining and Technology, Xuzhou, People’s Republic of China
3 shared publicationsLele Shi
Shanghai Railway Locomotive and Vehicle Development Co. LTD, Xuzhou Branch, Xuzhou, China
3 shared publications
Latest Publications
- 31 May 2024
- Published by Pleiades Publishing Ltd in Russian Journal of Physical Chemistry A
- Vol. 98 (5) , 997-1008
Evolution of the Material Properties of Rice Husk Hydrochar under Process Water Recycling and Its Adsorption Performance Research for Malachite Green
This study aims to investigate the evolution law of the material properties of rice husk (RH) hydrochar under quantitative process water recycling (QPWR) and to evaluate the changes in the adsorption performance of biomass hydrochar to malachite green (MG) with QPWR. In this study, 6 groups of RH samples were subjected to hydrothermal carbonization (HTC) experiments at 220°C, respectively. Except for the first HTC, which did not contain QPWR, the subsequent 5 HTC experiments all included the 100 mL process water from the previous HTC. The results demonstrated that after using QPWR, the mass yield (MY) of hydrochar increased from 68.51% without QPWR to 75.51% in the third QPWR; The carbon content increased from 58.09% of no QPWR to 76.63% of the fifth QPWR. Meanwhile, the volatile content decreased slowly from 42.70% without QPWR to 39.75% under the fifth QPWR, while the ash content increased slightly from 20.94% without QPWR to 21.45% under the fifth QPWR. SEM analysis showed that QPWR was beneficial to the decomposition and degradation of RH in HTC and promoted the accumulation of intermediates on the surface of hydrochar. BET-specific surface area and pore volume determination confirmed that QPWR could increase slightly the specific surface area and pore volume of hydrochar. Besides, the hydrochar produced by each HTC was used to adsorb malachite green, respectively. The results showed that the QPWR enhanced the adsorption performance of hydrochar, and the Langmuir–Freundlich adsorption model was more suitable to fit the adsorption law. These results highlighted the potential of QPWR in improving the application of biomass hydrochar.
- 31 May 2024
- Published by Pleiades Publishing Ltd in Russian Journal of Physical Chemistry A
- Vol. 98 (5) , 997-1008
Evolution of the Material Properties of Rice Husk Hydrochar under Process Water Recycling and Its Adsorption Performance Research for Malachite Green
This study aims to investigate the evolution law of the material properties of rice husk (RH) hydrochar under quantitative process water recycling (QPWR) and to evaluate the changes in the adsorption performance of biomass hydrochar to malachite green (MG) with QPWR. In this study, 6 groups of RH samples were subjected to hydrothermal carbonization (HTC) experiments at 220°C, respectively. Except for the first HTC, which did not contain QPWR, the subsequent 5 HTC experiments all included the 100 mL process water from the previous HTC. The results demonstrated that after using QPWR, the mass yield (MY) of hydrochar increased from 68.51% without QPWR to 75.51% in the third QPWR; The carbon content increased from 58.09% of no QPWR to 76.63% of the fifth QPWR. Meanwhile, the volatile content decreased slowly from 42.70% without QPWR to 39.75% under the fifth QPWR, while the ash content increased slightly from 20.94% without QPWR to 21.45% under the fifth QPWR. SEM analysis showed that QPWR was beneficial to the decomposition and degradation of RH in HTC and promoted the accumulation of intermediates on the surface of hydrochar. BET-specific surface area and pore volume determination confirmed that QPWR could increase slightly the specific surface area and pore volume of hydrochar. Besides, the hydrochar produced by each HTC was used to adsorb malachite green, respectively. The results showed that the QPWR enhanced the adsorption performance of hydrochar, and the Langmuir–Freundlich adsorption model was more suitable to fit the adsorption law. These results highlighted the potential of QPWR in improving the application of biomass hydrochar.
- Open Access
A Study on Processing Defects and Parameter Optimization in Abrasive Suspension Jet Cutting of Carbon-Fiber-Reinforced Plastics
Abrasive suspension jet (ASJ), an accurate cold-cutting technology, can address traditional processing issues relating to carbon-fiber-reinforced plastics (CFRPs) like tool wear, interlayer delamination, large heat-affected zone, and low surface roughness. This study employed the use of an ASJ to cut CFRPs and an ultra-depth optical microscope to scan the cut surface to analyze interlayer delamination, surface roughness, kerf taper, and shoulder damage. Regression analysis was conducted to establish a prediction model for cutting quality based on surface roughness, kerf taper, and shoulder damage. Various types of CFRP cutting quality were analyzed using jet parameters. It was found that the use of ASJ to process CFRP results in the following defects: The range of surface roughness variation is from 0.112 μm to 0.144 μm. Surface roughness is most influenced by stand-off distance, followed by traverse speed and jet pressure. The range of kerf taper variation is from 4.737° to 10.1°. Kerf taper is most influenced by stand-off distance, followed by jet pressure and traverse speed. The range of shoulder damage variation is from 3.384 μm2 to 10 μm2. Shoulder damage is most influenced by jet pressure, followed by traverse speed and stand-off distance. A prediction model for cutting quality was developed based on surface roughness, kerf taper, and shoulder damage, providing data support for ASJ cutting of CFRPs. The optimal parameter combination is a stand-off distance of 1 mm, a jet pressure of 30 MPa, and a traverse speed of 30 mm/min.
Open AccessA Study on Processing Defects and Parameter Optimization in Abrasive Suspension Jet Cutting of Carbon-Fiber-Reinforced Plastics
Abrasive suspension jet (ASJ), an accurate cold-cutting technology, can address traditional processing issues relating to carbon-fiber-reinforced plastics (CFRPs) like tool wear, interlayer delamination, large heat-affected zone, and low surface roughness. This study employed the use of an ASJ to cut CFRPs and an ultra-depth optical microscope to scan the cut surface to analyze interlayer delamination, surface roughness, kerf taper, and shoulder damage. Regression analysis was conducted to establish a prediction model for cutting quality based on surface roughness, kerf taper, and shoulder damage. Various types of CFRP cutting quality were analyzed using jet parameters. It was found that the use of ASJ to process CFRP results in the following defects: The range of surface roughness variation is from 0.112 μm to 0.144 μm. Surface roughness is most influenced by stand-off distance, followed by traverse speed and jet pressure. The range of kerf taper variation is from 4.737° to 10.1°. Kerf taper is most influenced by stand-off distance, followed by jet pressure and traverse speed. The range of shoulder damage variation is from 3.384 μm2 to 10 μm2. Shoulder damage is most influenced by jet pressure, followed by traverse speed and stand-off distance. A prediction model for cutting quality was developed based on surface roughness, kerf taper, and shoulder damage, providing data support for ASJ cutting of CFRPs. The optimal parameter combination is a stand-off distance of 1 mm, a jet pressure of 30 MPa, and a traverse speed of 30 mm/min.
- 8 July 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 121 (7-8) , 4625-4641
Proposal of “relative Young’s modulus” and its influence on cutting performance of abrasive suspension jet
- 8 July 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 121 (7-8) , 4625-4641
Proposal of “relative Young’s modulus” and its influence on cutting performance of abrasive suspension jet
- 3 August 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 117 (3-4) , 889-903
Effect of outlet pressure and polymer addition on accuracy of machining stainless steel by abrasive suspension jet
- 3 August 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 117 (3-4) , 889-903
Effect of outlet pressure and polymer addition on accuracy of machining stainless steel by abrasive suspension jet
- 24 March 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 114 (3-4) , 969-979
Experimental study on abrasive recycling in cutting with abrasive suspension water jet
- 24 March 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 114 (3-4) , 969-979
Experimental study on abrasive recycling in cutting with abrasive suspension water jet
- 2 February 2021
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 46 (8) , 7227-7237
New Application of Abrasive Slurry Jet in Coal Rocks Breaking and Prediction Model of Its Rock Breaking Ability
- 2 February 2021
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 46 (8) , 7227-7237
New Application of Abrasive Slurry Jet in Coal Rocks Breaking and Prediction Model of Its Rock Breaking Ability
- 19 November 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 112 (1-2) , 323-332
Quantitative analysis on the surface topography of Ti-6Al-4V machined by abrasive suspension jet
- 19 November 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 112 (1-2) , 323-332
Quantitative analysis on the surface topography of Ti-6Al-4V machined by abrasive suspension jet
- Open Access
- 10 September 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (18) , 6294
Rock Breaking Performance of TBM Disc Cutter Assisted by High-Pressure Water Jet
A high-pressure water jet can break rock efficiently, which is of great potential to overcome the problems of a tunnel boring machine (TBM) in full-face hard rock tunnel digging, such as low digging efficiency and high disc cutter wear rate. Therefore, this paper presented a new tunneling method that is a TBM coupled with a high-pressure water jet. The rock failure mechanism under the coupled forces of a disc cutter and water jet was analyzed at first. Then, the finite element method (FEM) and smoothed particle hydrodynamics (SPH) method were used to establish a numerical model of rock broken by the disc cutter and water jet. Effects of parameters on rock breaking performance were studied based on the numerical model. Moreover, an experiment of the water jet cutting marble was carried out to verify the reliability of the numerical simulation. Results showed that the high-pressure water jet can increase the TBM digging efficiency and decrease the forces and wear rate of the disc cutter. The optimum nozzle diameter is 1.5 mm, while the optimum jet velocity is 224.5 m/s in this simulation. The results can provide theoretical guidance and data support for designing the most efficient system of a TBM with a water jet for digging a full-face hard rock tunnel.
- 10 September 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (18) , 6294
Open AccessRock Breaking Performance of TBM Disc Cutter Assisted by High-Pressure Water Jet
A high-pressure water jet can break rock efficiently, which is of great potential to overcome the problems of a tunnel boring machine (TBM) in full-face hard rock tunnel digging, such as low digging efficiency and high disc cutter wear rate. Therefore, this paper presented a new tunneling method that is a TBM coupled with a high-pressure water jet. The rock failure mechanism under the coupled forces of a disc cutter and water jet was analyzed at first. Then, the finite element method (FEM) and smoothed particle hydrodynamics (SPH) method were used to establish a numerical model of rock broken by the disc cutter and water jet. Effects of parameters on rock breaking performance were studied based on the numerical model. Moreover, an experiment of the water jet cutting marble was carried out to verify the reliability of the numerical simulation. Results showed that the high-pressure water jet can increase the TBM digging efficiency and decrease the forces and wear rate of the disc cutter. The optimum nozzle diameter is 1.5 mm, while the optimum jet velocity is 224.5 m/s in this simulation. The results can provide theoretical guidance and data support for designing the most efficient system of a TBM with a water jet for digging a full-face hard rock tunnel.
- 1 May 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 108 (5-6) , 1875-1886
Study on cutting speed and energy utilization rate in processing stainless steel with abrasive water jet
- 1 May 2020
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 108 (5-6) , 1875-1886
Study on cutting speed and energy utilization rate in processing stainless steel with abrasive water jet
- 20 January 2020
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 42 (2) , 1-10
Principle and mechanical design of a new abrasive slurry jet and its performance testing
- 20 January 2020
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 42 (2) , 1-10
Principle and mechanical design of a new abrasive slurry jet and its performance testing