Sebastian Koelling
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Sebastian Koelling has a total of 161 co-authors. Here are the top co-authors by number of shared publications:
- Erik P. A. M. Bakkers
Department of Applied Physics, Eindhoven University of Technology, Eindhoven, The Netherlands
14 shared publications - Oussama Moutanabbir
École Polytechnique de Montréal C.P. 6079, Succ. Centre-Ville
11 shared publications - Simone Assali
École Polytechnique de Montréal C.P. 6079, Succ. Centre-Ville
11 shared publications - Marcel A. Verheijen
Eindhoven University of Technology, 5600 MB Eindhoven, The Netherlands
6 shared publications Mahmoud Atalla
Ecole Polytechnique de Montréal
5 shared publicationsMarcel A. Verheijen
Eurofins Materials Science BV , High Tech Campus 11 , 5656AE Eindhoven , The Netherlands
5 shared publications
Latest Publications
- 11 July 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-01 (36) , 1717
Reduced Pressure Chemical Vapour Deposition Growth of Nuclear Spin-Free 70Ge/28Si70Ge Heterostructures on Industrial Si-Ge Substrates
Spin qubits based on germanium (Ge) heterostructures are promising candidates for CMOS compatible quantum processors with long coherence times. This is in part due to the advantages of hole spins in Ge, such as their large spin orbit interaction and reduced hyperfine coupling with nuclear spins. The coherence and operation of hole spin qubits in planar Ge/SiGe heterostructures are both very sensitive to the nuclear spin bath. Therefore, developing nuclear spin-depleted materials is critical to enhance the performance of these qubits. To this end, it is important to eliminate the nuclear spin-full 29Si and 73Ge in the epitaxial Ge/SiGe heterostructures. Our group has recently demonstrated highly crystalline, defect free, isotopically purified (>99.9 at.% 70Ge) nuclear spin-depleted 70Ge quantum well (QW) heterostructures grown in a reduced pressure CVD using purified precursors (>99.9 at.% 70GeH4 and >99.99 at.% 28SiH4) on in situ grown reversed graded SiGe buffers. However, the extensive use of expensive purified precursors across the growth remained a problem. Here we demonstrate the regrowth of 70Ge QW heterostructures on easily available industrial SiGe substrates, leading to a major reduction of purified precursor consumption. The QW structures are grown with the forementioned precursors following a surface preparation based on HF and HCl cleans and high temperature anneals in hydrogen (Figure 1.a). X-ray diffraction experiments show excellent crystallinity of the regrown barriers and the QW (Figure 1.b). The obtained QW-barrier interfaces are notably sharper than for our previously reported heterostructures (Figure 1.c). The total spin-bearing isotope content in the regrowth has been determined to be below 7 ppm with atom probe tomography. Additional details on the surface characterization, fine tuning of the interface profiles and electron microscopy examination of the interfaces will be discussed at the conference. Figure 1
- 11 July 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-01 (36) , 1717
Reduced Pressure Chemical Vapour Deposition Growth of Nuclear Spin-Free 70Ge/28Si70Ge Heterostructures on Industrial Si-Ge Substrates
Spin qubits based on germanium (Ge) heterostructures are promising candidates for CMOS compatible quantum processors with long coherence times. This is in part due to the advantages of hole spins in Ge, such as their large spin orbit interaction and reduced hyperfine coupling with nuclear spins. The coherence and operation of hole spin qubits in planar Ge/SiGe heterostructures are both very sensitive to the nuclear spin bath. Therefore, developing nuclear spin-depleted materials is critical to enhance the performance of these qubits. To this end, it is important to eliminate the nuclear spin-full 29Si and 73Ge in the epitaxial Ge/SiGe heterostructures. Our group has recently demonstrated highly crystalline, defect free, isotopically purified (>99.9 at.% 70Ge) nuclear spin-depleted 70Ge quantum well (QW) heterostructures grown in a reduced pressure CVD using purified precursors (>99.9 at.% 70GeH4 and >99.99 at.% 28SiH4) on in situ grown reversed graded SiGe buffers. However, the extensive use of expensive purified precursors across the growth remained a problem. Here we demonstrate the regrowth of 70Ge QW heterostructures on easily available industrial SiGe substrates, leading to a major reduction of purified precursor consumption. The QW structures are grown with the forementioned precursors following a surface preparation based on HF and HCl cleans and high temperature anneals in hydrogen (Figure 1.a). X-ray diffraction experiments show excellent crystallinity of the regrown barriers and the QW (Figure 1.b). The obtained QW-barrier interfaces are notably sharper than for our previously reported heterostructures (Figure 1.c). The total spin-bearing isotope content in the regrowth has been determined to be below 7 ppm with atom probe tomography. Additional details on the surface characterization, fine tuning of the interface profiles and electron microscopy examination of the interfaces will be discussed at the conference. Figure 1
- 11 July 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-01 (31) , 1600
GeSn Nanowire Mid-Infrared Photodetectors and Spectrometers
Group IV GeSn nanowires (NWs) are emerging as promising candidates for mid-infrared (MIR) optoelectronic devices due to their tunable direct bandgap, high carrier mobility, and compatibility with silicon-based platforms. A core/shell NW structure with an ultra-thin Ge core has been utilized to produce high-quality GeSn alloys, offering two significant advantages: (1) the free sidewall facets of NWs effectively reduce lattice mismatch-induced compressive strain in the GeSn shell, and (2) the thin Ge core (< 20 nm) enhances the uniformity of Sn composition in the shell. Ge/Ge₁₋ₓSnₓ core/shell NWs are fabricated via chemical vapor deposition (CVD), involving a vapor-liquid-solid (VLS) Ge NW growth step and a Ge₁₋ₓSnₓ shell epitaxial growth step. Photodetectors based on Ge/Ge₁₋ₓSnₓ core/shell NWs with Sn compositions ranging from 8% to 18% have been demonstrated, achieving cutoff wavelengths spanning from 2.1 µm to 3.9 µm.[1,2] Additionally, the application of a short-wave infrared (SWIR) imager utilizing multiple NW photodetectors has been successfully demonstrated. NW-based photodetectors further benefit from the cavity resonance effect, wherein the resonance peak strongly depends on the NW diameter, enabling enhanced absorption at specific wavelengths.[3] Leveraging this effect, a GeSn NW on-chip infrared spectrometer is proposed. The device comprises multiple GeSn NW array photodiodes with varying diameters, enabling tunable absorption peaks. Finite-difference time-domain (FDTD) simulations were conducted to optimize design parameters, including NW diameter and pitch length. Vertical GeSn NW array photodiodes are fabricated by dry etching GeSn p-i-n multi-layer structures, followed by forming top and bottom contacts on n-type and p-type GeSn layers, respectively. The spectrometer reconstructs the detected spectrum using computational algorithms, providing a scalable and efficient solution for MIR sensing and imaging applications.[4] References [1] Luo, L. et al. ACS Photonics 9.3 (2022): 914-921. [2] Luo, L., et al. Nano Letters 24.16 (2024): 4979-4986. [3] Attiaoui, A., et al. Physical Review Applied 15.1 (2021): 014034. [4] Yang, Z., et al. Science 365.6457 (2019): 1017-1020.
- 11 July 2025
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2025-01 (31) , 1600
GeSn Nanowire Mid-Infrared Photodetectors and Spectrometers
Group IV GeSn nanowires (NWs) are emerging as promising candidates for mid-infrared (MIR) optoelectronic devices due to their tunable direct bandgap, high carrier mobility, and compatibility with silicon-based platforms. A core/shell NW structure with an ultra-thin Ge core has been utilized to produce high-quality GeSn alloys, offering two significant advantages: (1) the free sidewall facets of NWs effectively reduce lattice mismatch-induced compressive strain in the GeSn shell, and (2) the thin Ge core (< 20 nm) enhances the uniformity of Sn composition in the shell. Ge/Ge₁₋ₓSnₓ core/shell NWs are fabricated via chemical vapor deposition (CVD), involving a vapor-liquid-solid (VLS) Ge NW growth step and a Ge₁₋ₓSnₓ shell epitaxial growth step. Photodetectors based on Ge/Ge₁₋ₓSnₓ core/shell NWs with Sn compositions ranging from 8% to 18% have been demonstrated, achieving cutoff wavelengths spanning from 2.1 µm to 3.9 µm.[1,2] Additionally, the application of a short-wave infrared (SWIR) imager utilizing multiple NW photodetectors has been successfully demonstrated. NW-based photodetectors further benefit from the cavity resonance effect, wherein the resonance peak strongly depends on the NW diameter, enabling enhanced absorption at specific wavelengths.[3] Leveraging this effect, a GeSn NW on-chip infrared spectrometer is proposed. The device comprises multiple GeSn NW array photodiodes with varying diameters, enabling tunable absorption peaks. Finite-difference time-domain (FDTD) simulations were conducted to optimize design parameters, including NW diameter and pitch length. Vertical GeSn NW array photodiodes are fabricated by dry etching GeSn p-i-n multi-layer structures, followed by forming top and bottom contacts on n-type and p-type GeSn layers, respectively. The spectrometer reconstructs the detected spectrum using computational algorithms, providing a scalable and efficient solution for MIR sensing and imaging applications.[4] References [1] Luo, L. et al. ACS Photonics 9.3 (2022): 914-921. [2] Luo, L., et al. Nano Letters 24.16 (2024): 4979-4986. [3] Attiaoui, A., et al. Physical Review Applied 15.1 (2021): 014034. [4] Yang, Z., et al. Science 365.6457 (2019): 1017-1020.
- Open Access
- 16 May 2025
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 11 (20) , eadt6723
Mid-infrared group IV nanowire laser
Semiconductor nanowires have shown great potential for enabling ultracompact lasers for integrated photonics platforms. Despite the impressive progress in developing nanowire lasers, their integration into Si photonics platforms remains challenging largely because of the use of III-V and II-VI semiconductors as gain media. Recently, group IV nanowires, particularly direct bandgap GeSn nanowires capable of emitting above 2 μm, have emerged as promising cost-effective gain media for Si-compatible nanowire lasers, but there has been no successful demonstration of lasing from this seemingly promising nanowire platform. Herein, we report the experimental observation of lasing above 2 μm from a single bottom-up grown GeSn nanowire. By harnessing strain engineering and optimized cavity designs simultaneously, the single GeSn nanowire achieves an amplified material gain that can sufficiently overcome minimized optical losses, resulting in single-mode lasing with an ultralow threshold of ~5.3 kilowatts per square centimeter. Our finding paves the way for all–group IV mid-infrared photonic-integrated circuits with Si-compatible lasers for on-chip classical and quantum applications.
- 16 May 2025
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 11 (20) , eadt6723
Open AccessMid-infrared group IV nanowire laser
Semiconductor nanowires have shown great potential for enabling ultracompact lasers for integrated photonics platforms. Despite the impressive progress in developing nanowire lasers, their integration into Si photonics platforms remains challenging largely because of the use of III-V and II-VI semiconductors as gain media. Recently, group IV nanowires, particularly direct bandgap GeSn nanowires capable of emitting above 2 μm, have emerged as promising cost-effective gain media for Si-compatible nanowire lasers, but there has been no successful demonstration of lasing from this seemingly promising nanowire platform. Herein, we report the experimental observation of lasing above 2 μm from a single bottom-up grown GeSn nanowire. By harnessing strain engineering and optimized cavity designs simultaneously, the single GeSn nanowire achieves an amplified material gain that can sufficiently overcome minimized optical losses, resulting in single-mode lasing with an ultralow threshold of ~5.3 kilowatts per square centimeter. Our finding paves the way for all–group IV mid-infrared photonic-integrated circuits with Si-compatible lasers for on-chip classical and quantum applications.
- Open Access
- 24 December 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 136 (24)
Tracking of atomic planes in atom probe tomography
Atom probe tomography is a ubiquitous method in materials science and engineering capable of revealing the atomic-level three-dimensional composition of a plethora of materials. Beside the nature of atoms forming the analyzed material, atom probe data are also known to contain information on the crystallography. In particular, remnants of the atomic plane sets forming on the surface of the tip-shaped samples are commonly found in atom probe data sets of crystalline metallic materials. The plane remnants can be utilized to correlate the nano-scale chemical analysis that atom probe tomography provides with the crystallographic structure on the same scale. We describe a protocol to reveal and track the atomic planes systematically from raw atom probe data. We demonstrate for both metals and semiconductors that the extracted crystallographic can be used to calibrate a dynamic reconstruction of the respective data set acquired in atom probe tomography. Furthermore, we utilize the crystal planes to make precise measurements of layer thicknesses in atom probe data of semiconductor heterostructures.
- 24 December 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 136 (24)
Open AccessTracking of atomic planes in atom probe tomography
Atom probe tomography is a ubiquitous method in materials science and engineering capable of revealing the atomic-level three-dimensional composition of a plethora of materials. Beside the nature of atoms forming the analyzed material, atom probe data are also known to contain information on the crystallography. In particular, remnants of the atomic plane sets forming on the surface of the tip-shaped samples are commonly found in atom probe data sets of crystalline metallic materials. The plane remnants can be utilized to correlate the nano-scale chemical analysis that atom probe tomography provides with the crystallographic structure on the same scale. We describe a protocol to reveal and track the atomic planes systematically from raw atom probe data. We demonstrate for both metals and semiconductors that the extracted crystallographic can be used to calibrate a dynamic reconstruction of the respective data set acquired in atom probe tomography. Furthermore, we utilize the crystal planes to make precise measurements of layer thicknesses in atom probe data of semiconductor heterostructures.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (32) , 2327
In-Situ n-Type Doped Carrier-Injection Layers in GeSn Direct Bandgap LEDs for Methane Sensing
GeSn-based group-IV alloys are attracting great attention in the Si photonics community, as they are considered to be compatible with Complementary Metal Oxide Semiconductor (CMOS) technology. Alloying germanium with more than 8% of tin (Sn) results in direct bandgap semiconductors, with some optical gain in devices such as lasers. Recently, room temperature optically pumped lasing was achieved thanks to high Sn content stacks. GeSn alloys can be used for near, short and mid wavelength infra-red spectral range operation, notably for gas detection. Current efforts are focused on electro-optical GeSn IR devices such as light-emitting devices (LEDs), electrically pumped lasers and photodetectors. In this paper, we evaluate the impact of various types of in situ n-type doped carrier injection layers on top of GeSn direct bandgap LEDs. More precisely, we compare the performances of GeSn:P and Ge:P –capped mid IR LEDs. Using reduced pressure chemical vapor deposition and metastable growth conditions (e.g. fast growth rates at low temperature), high crystalline quality GeSn layers were grown on 200 mm diameter Ge-buffered Si(001) wafers (Figure a). In situ n-type doped Ge layers (sample A) and GeSn layers (sample B) were used to inject carriers into direct band gap Ge0.87Sn0.13 active layers beneath (Figure b). I(V) curves (Figure c) and Electro-Luminescence spectra (Figure d) were compared for sample B (GeSn:P) and sample A (Ge:P). Very similar I(V) behaviors were observed under forward bias for both samples. However, a higher dark current was measured under reverse bias for sample B than for sample A. This could be due to a higher number of defects in the thicker capping layer of sample B (240 nm) compared to that of sample A (50 nm). However, a 2-fold increase in the EL signal was obtained for sample B than sample A (Figure d). Temperature dependence electroluminescence measurements and atom probe tomography data will be used to explain the electroluminescence behavior differences between Samples A and B. Finally, even higher Sn content LEDs were fabricated to emit light at 3.3 µm (Figure e). A direct band gap Ge0.846Sn0.154LED (Sample C) with an in situ n-type doped Ge cap was placed in a gas cell filled with diluted methane. Its emission overlapped well with the absorption of methane (Figure f). The methane detection limit of our setup was evaluated (data not shown). To further increase the emitted power of GeSn LEDs, current spreading was studied for different top contact geometries. Emission maps collected by an InSb camera at room temperature showed a definite dependence of light emission on electrical contact geometry (Figure g). Investigations are underway to further increase light extraction from LEDs and improve their performances for use in environmental sensors. Acknowledgement: This work was supported by the European Union’s Horizon 2020 LASTSTEP Project under the grant agreement ID: 101070208, the EDEN Carnot project and the CEA DRF-DRT Phare project. We gratefully acknowledge the clean room staff from LETI and IRIG for their technical support. Figure 1
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (32) , 2327
In-Situ n-Type Doped Carrier-Injection Layers in GeSn Direct Bandgap LEDs for Methane Sensing
GeSn-based group-IV alloys are attracting great attention in the Si photonics community, as they are considered to be compatible with Complementary Metal Oxide Semiconductor (CMOS) technology. Alloying germanium with more than 8% of tin (Sn) results in direct bandgap semiconductors, with some optical gain in devices such as lasers. Recently, room temperature optically pumped lasing was achieved thanks to high Sn content stacks. GeSn alloys can be used for near, short and mid wavelength infra-red spectral range operation, notably for gas detection. Current efforts are focused on electro-optical GeSn IR devices such as light-emitting devices (LEDs), electrically pumped lasers and photodetectors. In this paper, we evaluate the impact of various types of in situ n-type doped carrier injection layers on top of GeSn direct bandgap LEDs. More precisely, we compare the performances of GeSn:P and Ge:P –capped mid IR LEDs. Using reduced pressure chemical vapor deposition and metastable growth conditions (e.g. fast growth rates at low temperature), high crystalline quality GeSn layers were grown on 200 mm diameter Ge-buffered Si(001) wafers (Figure a). In situ n-type doped Ge layers (sample A) and GeSn layers (sample B) were used to inject carriers into direct band gap Ge0.87Sn0.13 active layers beneath (Figure b). I(V) curves (Figure c) and Electro-Luminescence spectra (Figure d) were compared for sample B (GeSn:P) and sample A (Ge:P). Very similar I(V) behaviors were observed under forward bias for both samples. However, a higher dark current was measured under reverse bias for sample B than for sample A. This could be due to a higher number of defects in the thicker capping layer of sample B (240 nm) compared to that of sample A (50 nm). However, a 2-fold increase in the EL signal was obtained for sample B than sample A (Figure d). Temperature dependence electroluminescence measurements and atom probe tomography data will be used to explain the electroluminescence behavior differences between Samples A and B. Finally, even higher Sn content LEDs were fabricated to emit light at 3.3 µm (Figure e). A direct band gap Ge0.846Sn0.154LED (Sample C) with an in situ n-type doped Ge cap was placed in a gas cell filled with diluted methane. Its emission overlapped well with the absorption of methane (Figure f). The methane detection limit of our setup was evaluated (data not shown). To further increase the emitted power of GeSn LEDs, current spreading was studied for different top contact geometries. Emission maps collected by an InSb camera at room temperature showed a definite dependence of light emission on electrical contact geometry (Figure g). Investigations are underway to further increase light extraction from LEDs and improve their performances for use in environmental sensors. Acknowledgement: This work was supported by the European Union’s Horizon 2020 LASTSTEP Project under the grant agreement ID: 101070208, the EDEN Carnot project and the CEA DRF-DRT Phare project. We gratefully acknowledge the clean room staff from LETI and IRIG for their technical support. Figure 1
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (32) , 2328
(Invited) Group IV Mid-Infrared Optoelectronics Leveraging Nanoscale Growth Substrates
Mid-infrared (MIR) optoelectronic devices are of utmost importance to a plethora of applications such as night vision, thermal sensing, autonomous vehicles, free-space communication, and spectroscopy. To this end, leveraging the ubiquitous silicon-based processing has emerged as a powerful strategy that can be accomplished through the use of group IV germanium-tin (GeSn) alloys. Indeed, due to their compatibility with silicon and their tunable bandgap energy covering the entire MWIR range, GeSn semiconductors are frontrunner platforms for compact and scalable MIR technologies. However, the GeSn large lattice parameter has been a major hurdle limiting the quality of GeSn epitaxy on silicon wafers. These limitations are further exacerbated as Ge1−xSnx layers and heterostructures with Sn contents at least one order of magnitude higher than the solubility are needed for device structures relevant to MWIR applications. In this regime, the as-grown layers are typically under a significant compressive strain, which impacts the bandgap directness and increases its energy at the Γ point, thus hindering the device performance and limiting the covered range of the MIR spectrum. This compressive strain build-up not only affects the band structure but also limits the incorporation of Sn atoms in the growing layer, making the control of Sn content a daunting task. In this presentation, we will show and discuss how sub-20 nm Ge nanowires provide effective compliant substrates to grow Ge1−xSnx alloys with a composition uniformity over several micrometers with a very limited build-up of the compressive strain. Ge/Ge1−xSnx structures with Sn content spanning the 6 to 18 at.% range are achieved. We will also demonstrate the integration of the obtained materials in optoelectronic device processing leading to tunable detectors and emitters [1,2]. For instance, photodetectors based on these materials were found to exhibit a high signal-to-noise ratio at room temperature and provide a tunable cutoff wavelength covering the 2.0 µm to 3.9 µm range. Additionally, the processed detectors were also integrated in uncooled imagers enabling the acquisition of high-quality images under both broadband and laser illuminations without the use of the lock-in amplifier technique. Finally, progress towards achieving nanoscale GeSn lasers will also be discussed [2]. References: [1] L. Luo, M. R. M. Atalla, S. Assali, S. Koelling, G. Daligou, and O. Moutanabbir, Nano Letters (in press). https://doi.org/10.1021/acs.nanolett.4c00759 [2] Y. Kim, S. Assali, H.-J. Joo, S. Koelling, M. Chen, L. Luo, X. Shi, D. Burt, Z. Ikonic, D. Nam, and O. Moutanabbir, Nature Communications 14, 4393 (2023).
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (32) , 2328
(Invited) Group IV Mid-Infrared Optoelectronics Leveraging Nanoscale Growth Substrates
Mid-infrared (MIR) optoelectronic devices are of utmost importance to a plethora of applications such as night vision, thermal sensing, autonomous vehicles, free-space communication, and spectroscopy. To this end, leveraging the ubiquitous silicon-based processing has emerged as a powerful strategy that can be accomplished through the use of group IV germanium-tin (GeSn) alloys. Indeed, due to their compatibility with silicon and their tunable bandgap energy covering the entire MWIR range, GeSn semiconductors are frontrunner platforms for compact and scalable MIR technologies. However, the GeSn large lattice parameter has been a major hurdle limiting the quality of GeSn epitaxy on silicon wafers. These limitations are further exacerbated as Ge1−xSnx layers and heterostructures with Sn contents at least one order of magnitude higher than the solubility are needed for device structures relevant to MWIR applications. In this regime, the as-grown layers are typically under a significant compressive strain, which impacts the bandgap directness and increases its energy at the Γ point, thus hindering the device performance and limiting the covered range of the MIR spectrum. This compressive strain build-up not only affects the band structure but also limits the incorporation of Sn atoms in the growing layer, making the control of Sn content a daunting task. In this presentation, we will show and discuss how sub-20 nm Ge nanowires provide effective compliant substrates to grow Ge1−xSnx alloys with a composition uniformity over several micrometers with a very limited build-up of the compressive strain. Ge/Ge1−xSnx structures with Sn content spanning the 6 to 18 at.% range are achieved. We will also demonstrate the integration of the obtained materials in optoelectronic device processing leading to tunable detectors and emitters [1,2]. For instance, photodetectors based on these materials were found to exhibit a high signal-to-noise ratio at room temperature and provide a tunable cutoff wavelength covering the 2.0 µm to 3.9 µm range. Additionally, the processed detectors were also integrated in uncooled imagers enabling the acquisition of high-quality images under both broadband and laser illuminations without the use of the lock-in amplifier technique. Finally, progress towards achieving nanoscale GeSn lasers will also be discussed [2]. References: [1] L. Luo, M. R. M. Atalla, S. Assali, S. Koelling, G. Daligou, and O. Moutanabbir, Nano Letters (in press). https://doi.org/10.1021/acs.nanolett.4c00759 [2] Y. Kim, S. Assali, H.-J. Joo, S. Koelling, M. Chen, L. Luo, X. Shi, D. Burt, Z. Ikonic, D. Nam, and O. Moutanabbir, Nature Communications 14, 4393 (2023).
- Open Access
- 1 May 2024
- Published by AIP Publishing in APL Photonics
- Vol. 9 (5)
Extended short-wave infrared high-speed all-GeSn PIN photodetectors on silicon
There is an increasing need for silicon-compatible high-bandwidth extended-short wave infrared (e-SWIR) photodetectors (PDs) to implement cost-effective and scalable optoelectronic devices. These systems are quintessential to address several technological bottlenecks in detection and ranging, surveillance, ultrafast spectroscopy, and imaging. In fact, current e-SWIR high-bandwidth PDs are predominantly made of III–V compound semiconductors and thus are costly and suffer a limited integration on silicon besides a low responsivity at wavelengths exceeding 2.3 μm. To circumvent these challenges, Ge1−xSnx semiconductors have been proposed as building blocks for silicon-integrated high-speed e-SWIR devices. Herein, this study demonstrates vertical all-GeSn PIN PDs consisting of p-Ge0.92Sn0.08/i-Ge0.91Sn0.09/n-Ge0.89Sn0.11 and p-Ge0.91Sn0.09/i-Ge0.88Sn0.12/n-Ge0.87Sn0.13 heterostructures grown on silicon following a step-graded temperature-controlled epitaxy protocol. The performance of these PDs was investigated as a function of the device diameter in the 10–30 μm range. The developed PD devices yield a high bandwidth of 12.4 GHz at a bias of 5 V for a device diameter of 10 μm. Moreover, these devices show a high responsivity of 0.24 A/W, a low noise, and a 2.8 μm cutoff wavelength, thus covering the whole e-SWIR range.
- 1 May 2024
- Published by AIP Publishing in APL Photonics
- Vol. 9 (5)
Open AccessExtended short-wave infrared high-speed all-GeSn PIN photodetectors on silicon
There is an increasing need for silicon-compatible high-bandwidth extended-short wave infrared (e-SWIR) photodetectors (PDs) to implement cost-effective and scalable optoelectronic devices. These systems are quintessential to address several technological bottlenecks in detection and ranging, surveillance, ultrafast spectroscopy, and imaging. In fact, current e-SWIR high-bandwidth PDs are predominantly made of III–V compound semiconductors and thus are costly and suffer a limited integration on silicon besides a low responsivity at wavelengths exceeding 2.3 μm. To circumvent these challenges, Ge1−xSnx semiconductors have been proposed as building blocks for silicon-integrated high-speed e-SWIR devices. Herein, this study demonstrates vertical all-GeSn PIN PDs consisting of p-Ge0.92Sn0.08/i-Ge0.91Sn0.09/n-Ge0.89Sn0.11 and p-Ge0.91Sn0.09/i-Ge0.88Sn0.12/n-Ge0.87Sn0.13 heterostructures grown on silicon following a step-graded temperature-controlled epitaxy protocol. The performance of these PDs was investigated as a function of the device diameter in the 10–30 μm range. The developed PD devices yield a high bandwidth of 12.4 GHz at a bias of 5 V for a device diameter of 10 μm. Moreover, these devices show a high responsivity of 0.24 A/W, a low noise, and a 2.8 μm cutoff wavelength, thus covering the whole e-SWIR range.
- 16 January 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (3) , 031103
Dark current in monolithic extended-SWIR GeSn PIN photodetectors
Monolithic integration of extended short-wave infrared photodetectors (PDs) on silicon is highly sought-after to implement manufacturable, cost-effective sensing and imaging technologies. With this perspective, GeSn PIN PDs have been the subject of extensive investigations because of their bandgap tunability and silicon compatibility. However, due to growth defects, these PDs suffer a relatively high dark current density as compared to commercial III–V PDs. Herein, we elucidate the mechanisms governing the dark current in m GeSn PDs at a Sn content of 10 at. %. It was found that in the temperature range of 293–363 K and at low bias, the diffusion and Shockley–Read–Hall (SRH) leakage mechanisms dominate the dark current in small diameter ( m) devices, while combined SRH and trap assisted tunneling (TAT) leakage mechanisms are prominent in larger diameter ( m) devices. However, at high reverse bias, the TAT leakage mechanism becomes dominant regardless of the operating temperature and device size. The effective non-radiative carrier lifetime in these devices was found to reach –150 ps at low bias. Owing to TAT leakage current, however, this lifetime reduces progressively as the bias increases.- 16 January 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (3) , 031103
Dark current in monolithic extended-SWIR GeSn PIN photodetectors
Monolithic integration of extended short-wave infrared photodetectors (PDs) on silicon is highly sought-after to implement manufacturable, cost-effective sensing and imaging technologies. With this perspective, GeSn PIN PDs have been the subject of extensive investigations because of their bandgap tunability and silicon compatibility. However, due to growth defects, these PDs suffer a relatively high dark current density as compared to commercial III–V PDs. Herein, we elucidate the mechanisms governing the dark current in m GeSn PDs at a Sn content of 10 at. %. It was found that in the temperature range of 293–363 K and at low bias, the diffusion and Shockley–Read–Hall (SRH) leakage mechanisms dominate the dark current in small diameter ( m) devices, while combined SRH and trap assisted tunneling (TAT) leakage mechanisms are prominent in larger diameter ( m) devices. However, at high reverse bias, the TAT leakage mechanism becomes dominant regardless of the operating temperature and device size. The effective non-radiative carrier lifetime in these devices was found to reach –150 ps at low bias. Owing to TAT leakage current, however, this lifetime reduces progressively as the bias increases.- Open Access
- 1 December 2022
- Published by Wiley in Advanced Materials Interfaces
- Vol. 10 (3)
Three‐Dimensional Atomic‐Scale Tomography of Buried Semiconductor Heterointerfaces
Atom probes generate three‐dimensional atomic‐scale tomographies of material volumes corresponding to the size of modern‐day solid‐state devices. Here, the capabilities of atom probe tomography are evaluated to analyze buried interfaces in semiconductor heterostructures relevant for electronic and quantum devices. Employing brute‐force search, the current dominant reconstruction protocol to generate tomographic three‐dimensional images from Atom Probe data is advanced to its limits. Using Si/SiGe heterostructure for qubits as a model system, the authors show that it is possible to extract interface properties like roughness and width that agree with transmission electron microscopy observations on the sub‐nanometer scale in an automated and highly reproducible manner. The demonstrated approach is a versatile method for atomic‐scale characterization of buried interfaces in semiconductor heterostructures.
- 1 December 2022
- Published by Wiley in Advanced Materials Interfaces
- Vol. 10 (3)
Open AccessThree‐Dimensional Atomic‐Scale Tomography of Buried Semiconductor Heterointerfaces
Atom probes generate three‐dimensional atomic‐scale tomographies of material volumes corresponding to the size of modern‐day solid‐state devices. Here, the capabilities of atom probe tomography are evaluated to analyze buried interfaces in semiconductor heterostructures relevant for electronic and quantum devices. Employing brute‐force search, the current dominant reconstruction protocol to generate tomographic three‐dimensional images from Atom Probe data is advanced to its limits. Using Si/SiGe heterostructure for qubits as a model system, the authors show that it is possible to extract interface properties like roughness and width that agree with transmission electron microscopy observations on the sub‐nanometer scale in an automated and highly reproducible manner. The demonstrated approach is a versatile method for atomic‐scale characterization of buried interfaces in semiconductor heterostructures.
- 17 November 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (19) , 195305
Micrometer-thick, atomically random Si0.06Ge0.90Sn0.04 for silicon-integrated infrared optoelectronics
A true monolithic infrared photonics platform is within reach if strain and bandgap energy can be independently engineered in SiGeSn semiconductors. Herein, we investigate the structural and optoelectronic properties of a 1.5 μm-thick Si0.06Ge0.90Sn0.04 layer that is nearly lattice-matched to a Ge on Si substrate. Atomic-level studies demonstrate high crystalline quality and uniform composition and show no sign of short-range ordering and clusters. Room-temperature spectroscopic ellipsometry and transmission measurements show direct bandgap absorption at 0.83 eV and a reduced indirect bandgap absorption at lower energies. Si0.06Ge0.90Sn0.04 photoconductive devices operating at room temperature exhibit dark current and spectral responsivity (1 A/W below 1.5 μm wavelengths) similar to Ge on Si devices, with the advantage of a near-infrared bandgap tunable by alloy composition. These results underline the relevance of SiGeSn semiconductors in implementing a group IV material platform for silicon-integrated infrared optoelectronics.
- 17 November 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 132 (19) , 195305
Micrometer-thick, atomically random Si0.06Ge0.90Sn0.04 for silicon-integrated infrared optoelectronics
A true monolithic infrared photonics platform is within reach if strain and bandgap energy can be independently engineered in SiGeSn semiconductors. Herein, we investigate the structural and optoelectronic properties of a 1.5 μm-thick Si0.06Ge0.90Sn0.04 layer that is nearly lattice-matched to a Ge on Si substrate. Atomic-level studies demonstrate high crystalline quality and uniform composition and show no sign of short-range ordering and clusters. Room-temperature spectroscopic ellipsometry and transmission measurements show direct bandgap absorption at 0.83 eV and a reduced indirect bandgap absorption at lower energies. Si0.06Ge0.90Sn0.04 photoconductive devices operating at room temperature exhibit dark current and spectral responsivity (1 A/W below 1.5 μm wavelengths) similar to Ge on Si devices, with the advantage of a near-infrared bandgap tunable by alloy composition. These results underline the relevance of SiGeSn semiconductors in implementing a group IV material platform for silicon-integrated infrared optoelectronics.