Ali Ghadimi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ali Ghadimi has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
- Toraj Mohammadi
Center of Excellence for Membrane Research and Technology, Department of Chemical, Petroleum and Gas Engineering, Iran University of Science and Technology (IUST), Tehran, Iran
17 shared publications - Mohtada Sadrzadeh
University of Alberta
7 shared publications - Hesamoddin Rabiee
Department of Chemistry, Biochemistry and Pharmaceutical Sciences, University Bern, Freiestrasse 3, CH-3012 Bern, Switzerland
5 shared publications - Somayeh Norouzbahari
Faculty of Chemistry, Kharazmi University, 15719-14911 Tehran, Iran
5 shared publications Behrouz Sadatnia
4 shared publicationsVahid Vatanpour
3 shared publications
Latest Publications
- Open Access
Air-to-Air Heat and Moisture Recovery in a Plate-Frame Exchanger Using Composite and Asymmetric Membranes
The present work studied an air-to-air exchanger comprising a flat plate module with a diagonal channel and a counterflow configuration for the air streams. The objective of this study was to remove moisture and sensible heat from an exhaust air stream by indirect contact with another air stream. The temperature and flow rate of the exhaust air was in the range of 40–80 °C and 1–5 L·min−1, respectively, and the fresh ambient air to exhaust air flow ratio was 1–5. An asymmetric porous membrane (P-MEM), a thin film composite membrane (C-MEM), and a kraft paper were used as the core for the heat exchange module. The most influential parameter was the humid air temperature, with a direct positive effect (50–60%) due to the increase in the kinetic energy of the water molecules. The other effective parameter was the flow rate of the humid gas with a reverse effect on the enthalpy exchanger performance (25–37%). The ratio of “fresh” air to “exhaust” air had the lowest positive effect (8–10%) on the total effectiveness. The sensible effectiveness of different membranes under the studied conditions was relatively the same, showing their similar heat conductivity. However, the kraft paper showed the best performance compared to the synthetic membranes due to having a porous/hydrophile texture. P-MEM with an asymmetric porous texture showed the closest performance to kraft paper. Furthermore, it was found that under limited conditions, such as higher temperatures (70 and 80 °C) and flow rates (5 L·min−1) for the humid air, the performance of P-MEM was a little better than the kraft paper. However, C-MEM with the lowest total effectiveness and overall heat transfer coefficient (150–210 W·m−2·K−1) showed that the hydrophile PEBAX layer could not contribute to moisture recovery due to its high thickness.
Open AccessAir-to-Air Heat and Moisture Recovery in a Plate-Frame Exchanger Using Composite and Asymmetric Membranes
The present work studied an air-to-air exchanger comprising a flat plate module with a diagonal channel and a counterflow configuration for the air streams. The objective of this study was to remove moisture and sensible heat from an exhaust air stream by indirect contact with another air stream. The temperature and flow rate of the exhaust air was in the range of 40–80 °C and 1–5 L·min−1, respectively, and the fresh ambient air to exhaust air flow ratio was 1–5. An asymmetric porous membrane (P-MEM), a thin film composite membrane (C-MEM), and a kraft paper were used as the core for the heat exchange module. The most influential parameter was the humid air temperature, with a direct positive effect (50–60%) due to the increase in the kinetic energy of the water molecules. The other effective parameter was the flow rate of the humid gas with a reverse effect on the enthalpy exchanger performance (25–37%). The ratio of “fresh” air to “exhaust” air had the lowest positive effect (8–10%) on the total effectiveness. The sensible effectiveness of different membranes under the studied conditions was relatively the same, showing their similar heat conductivity. However, the kraft paper showed the best performance compared to the synthetic membranes due to having a porous/hydrophile texture. P-MEM with an asymmetric porous texture showed the closest performance to kraft paper. Furthermore, it was found that under limited conditions, such as higher temperatures (70 and 80 °C) and flow rates (5 L·min−1) for the humid air, the performance of P-MEM was a little better than the kraft paper. However, C-MEM with the lowest total effectiveness and overall heat transfer coefficient (150–210 W·m−2·K−1) showed that the hydrophile PEBAX layer could not contribute to moisture recovery due to its high thickness.
- 1 September 2021
- Published by Elsevier in Microporous and Mesoporous Materials
- Vol. 324, 111292
CO2 and CH4 diffusivities through synthesized ZIF-8 nanocrystals: An experimental and theoretical investigation
- 1 September 2021
- Published by Elsevier in Microporous and Mesoporous Materials
- Vol. 324, 111292
CO2 and CH4 diffusivities through synthesized ZIF-8 nanocrystals: An experimental and theoretical investigation
- 1 October 2020
- Published by Elsevier in Journal of Membrane Science
- Vol. 611
Selective oxidation of benzene to phenol using functionalized membrane via Fenton-like process
- 1 October 2020
- Published by Elsevier in Journal of Membrane Science
- Vol. 611
Selective oxidation of benzene to phenol using functionalized membrane via Fenton-like process
- 1 September 2019
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 102, 524-535
Ionic liquid tethered PEG-based polyurethane-siloxane membranes for efficient CO2/CH4 separation
- 1 September 2019
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 102, 524-535
Ionic liquid tethered PEG-based polyurethane-siloxane membranes for efficient CO2/CH4 separation
- 1 January 2019
- Published by Elsevier in Reactive and Functional Polymers
- Vol. 134, 74-84
Synergistic effect of carboxylated-MWCNTs on the performance of acrylic acid UV-grafted polyamide nanofiltration membranes
- 1 January 2019
- Published by Elsevier in Reactive and Functional Polymers
- Vol. 134, 74-84
Synergistic effect of carboxylated-MWCNTs on the performance of acrylic acid UV-grafted polyamide nanofiltration membranes
- 1 November 2018
- Published by Elsevier in Diamond and Related Materials
- Vol. 90, 244-255
Effect of detonation nanodiamond on the properties and performance of polyethersulfone nanocomposite membrane
- 1 November 2018
- Published by Elsevier in Diamond and Related Materials
- Vol. 90, 244-255
Effect of detonation nanodiamond on the properties and performance of polyethersulfone nanocomposite membrane
- 1 October 2018
- Published by Elsevier in Journal of Membrane Science
- Vol. 563, 643-654
Geometric restriction of microporous supports on gas permeance efficiency of thin film composite membranes
- 1 October 2018
- Published by Elsevier in Journal of Membrane Science
- Vol. 563, 643-654
Geometric restriction of microporous supports on gas permeance efficiency of thin film composite membranes
- 1 August 2018
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 89, 41-51
Antifouling polyvinylidene fluoride ultrafiltration membrane fabricated from embedding polypyrrole coated multiwalled carbon nanotubes
- 1 August 2018
- Published by Elsevier in Materials Science and Engineering: C
- Vol. 89, 41-51
Antifouling polyvinylidene fluoride ultrafiltration membrane fabricated from embedding polypyrrole coated multiwalled carbon nanotubes