Kwuang-Han Chang
Research Subjects
Research Interests
Kwuang-Han Chang has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Chih-Cheng Hsieh
National Tsing Hua University
5 shared publications - Kazuya Mori
Brillnics Japan Inc., Tokyo, Japan
2 shared publications - Rimon Ikeno
Brillnics Japan Inc., Tokyo, Japan
2 shared publications Andrew Berkovich
Meta, Redmond, WA, USA
1 shared publication- Chia-Hsiang Yang
National Taiwan University
1 shared publication Chiao Liu
Meta, Redmond, WA, USA
1 shared publication
Latest Publications
- 5 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (6) , 3510-3520
A 400×400 3.24- μ m 117-dB Dynamic Range Three-Layer Stacked Digital Pixel Sensor With Triple Quantization and Fixed Pattern Noise Correction
This article presents a $400\times 400$ digital pixel sensor (DPS) with a 3.24- $\mu $ m pixel pitch, fabricated using a 45-/40-/40-nm three-layer stacked process. The sensor achieves single-exposure high dynamic range (SEHDR) through overlapped triple quantization (3Q), fixed pattern noise correction (FPN-C), and black level correction (BLC). An on-chip image signal processor (ISP) is integrated to support defect pixel correction (DPC), SEHDR linearization, and gamma correction. Sparse transmission (ST) is incorporated to reduce transmitted data volume and, consequently, transmission power consumption. A wafer-level chip-scale package (WLCSP) with two redistribution layers (RDLs) is employed, resulting in a compact form factor of $2.47\times 1.85$ mm2. This work achieves a dynamic range (DR) of 117 dB while consuming 2.45 mW at 30 frames/s (fps), yielding a figure of merit (FoM) of 0.0046 e ${}^{-}_{\text {rms}} {\,}{\,}\times $ pJ, and is developed to meet the growing demands of augmented reality (AR) and virtual reality (VR) applications.
- 5 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (6) , 3510-3520
A 400×400 3.24- μ m 117-dB Dynamic Range Three-Layer Stacked Digital Pixel Sensor With Triple Quantization and Fixed Pattern Noise Correction
This article presents a $400\times 400$ digital pixel sensor (DPS) with a 3.24- $\mu $ m pixel pitch, fabricated using a 45-/40-/40-nm three-layer stacked process. The sensor achieves single-exposure high dynamic range (SEHDR) through overlapped triple quantization (3Q), fixed pattern noise correction (FPN-C), and black level correction (BLC). An on-chip image signal processor (ISP) is integrated to support defect pixel correction (DPC), SEHDR linearization, and gamma correction. Sparse transmission (ST) is incorporated to reduce transmitted data volume and, consequently, transmission power consumption. A wafer-level chip-scale package (WLCSP) with two redistribution layers (RDLs) is employed, resulting in a compact form factor of $2.47\times 1.85$ mm2. This work achieves a dynamic range (DR) of 117 dB while consuming 2.45 mW at 30 frames/s (fps), yielding a figure of merit (FoM) of 0.0046 e ${}^{-}_{\text {rms}} {\,}{\,}\times $ pJ, and is developed to meet the growing demands of augmented reality (AR) and virtual reality (VR) applications.
- Open Access
Improvement in Random Noise for Pixel-Parallel Single-Slope ADC with Consideration of Flicker Noise Effect
We propose and demonstrate a low-random-noise (RN) design for pixel-parallel single-slope ADCs (SS-ADCs), achieving 2.2 e-rms in a 3.24 µm pixel. In this paper, we discuss AC-based RN estimation with respect to the comparator bias current and a bandwidth-limiting capacitor in digital-pixel sensors (DPSs). RN is composed of thermal noise (TN) and flicker noise (FN), where FN can be a major contributor in DPSs because of its area limitation. We express the concise equation to estimate the FN/TN ratio, in which the FN characteristic is modulated by the correlated double sampling (CDS) operation. We also study the effective RN bandwidth, which increases due to the ramp slope transient effect and introduces a noise bandwidth (NBW) coefficient, to estimate the effective NBW. This study provides insights into the area arrangement of the small-pixel DPS design. A high-gain single-ended comparator is introduced to realize an area-efficient DPS without digital CDS (D-CDS). Noise analysis of its pixel design shows that FN becomes the main contributor, and further RN improvement by limiting NBW or D-CDS is not promising under these conditions.
Open AccessImprovement in Random Noise for Pixel-Parallel Single-Slope ADC with Consideration of Flicker Noise Effect
We propose and demonstrate a low-random-noise (RN) design for pixel-parallel single-slope ADCs (SS-ADCs), achieving 2.2 e-rms in a 3.24 µm pixel. In this paper, we discuss AC-based RN estimation with respect to the comparator bias current and a bandwidth-limiting capacitor in digital-pixel sensors (DPSs). RN is composed of thermal noise (TN) and flicker noise (FN), where FN can be a major contributor in DPSs because of its area limitation. We express the concise equation to estimate the FN/TN ratio, in which the FN characteristic is modulated by the correlated double sampling (CDS) operation. We also study the effective RN bandwidth, which increases due to the ramp slope transient effect and introduces a noise bandwidth (NBW) coefficient, to estimate the effective NBW. This study provides insights into the area arrangement of the small-pixel DPS design. A high-gain single-ended comparator is introduced to realize an area-efficient DPS without digital CDS (D-CDS). Noise analysis of its pixel design shows that FN becomes the main contributor, and further RN improvement by limiting NBW or D-CDS is not promising under these conditions.
- 19 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (10) , 2691-2702
A Calibration-Free 13-Bit 10-MS/s Full-Analog SAR ADC With Continuous-Time Feedforward Cascaded Op-Amps
- 19 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (10) , 2691-2702
A Calibration-Free 13-Bit 10-MS/s Full-Analog SAR ADC With Continuous-Time Feedforward Cascaded Op-Amps
- 6 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (6) , 1624-1635
A Calibration-Free 12-bit 50-MS/s Full-Analog SAR ADC With Feedback Zero-Crossing Detectors
This paper presents a calibration-free 12-bit 50-MS/s full-analog SAR analog-to-digital (A-to-D) converter (ADC) in 40-nm CMOS, which integrates the functions of comparator, SAR logic, and digital-to-analog converter (DAC) switches into multiple feedback zero-crossing detectors (FB-ZCDs). By eliminating all the digital circuits, the full-analog bit conversions operate with the asynchronous amplification-to-regeneration (A-to-R) operation that highly relaxes the requirements of the analog circuits and reference generator. This paper is implemented without any calibration, where the non-ideal effects (offset mismatch, insufficient residue, and noise) are mitigated and eliminated with the proposed techniques as follows. The offset mismatches among the FB-ZCDs are covered by the redundancies of the sub-radix DAC arrangement in the coarse ADC. The bottom-plate coupling compensators (BPCCs) are proposed to correct the consecutive SAR decision errors as quantizing the insufficient residue. The shared FB-ZCD with capacitor coupling decision (CCD) network is developed to obtain the identical offset in the fine ADC. Amplification extension (AE) technique is proposed to enhance the precision of the shared FB-ZCD by reconfiguring as a complementary inverter-based amplifier with the extended amplification period to enhance the output SNR. This paper occupies an active area of 0.01 mm² and achieves the Nyquist-rate signal-to-noise-and-distortion ratio (SNDR), spurious-free dynamic range (SFDR), Walden figure-of-merit (FoMW), and Schreier FoM (FoMS) of 64.1, 75.6 dB, 5.3 fJ/conversion step, and 172.8 dB, respectively.
- 6 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (6) , 1624-1635
A Calibration-Free 12-bit 50-MS/s Full-Analog SAR ADC With Feedback Zero-Crossing Detectors
This paper presents a calibration-free 12-bit 50-MS/s full-analog SAR analog-to-digital (A-to-D) converter (ADC) in 40-nm CMOS, which integrates the functions of comparator, SAR logic, and digital-to-analog converter (DAC) switches into multiple feedback zero-crossing detectors (FB-ZCDs). By eliminating all the digital circuits, the full-analog bit conversions operate with the asynchronous amplification-to-regeneration (A-to-R) operation that highly relaxes the requirements of the analog circuits and reference generator. This paper is implemented without any calibration, where the non-ideal effects (offset mismatch, insufficient residue, and noise) are mitigated and eliminated with the proposed techniques as follows. The offset mismatches among the FB-ZCDs are covered by the redundancies of the sub-radix DAC arrangement in the coarse ADC. The bottom-plate coupling compensators (BPCCs) are proposed to correct the consecutive SAR decision errors as quantizing the insufficient residue. The shared FB-ZCD with capacitor coupling decision (CCD) network is developed to obtain the identical offset in the fine ADC. Amplification extension (AE) technique is proposed to enhance the precision of the shared FB-ZCD by reconfiguring as a complementary inverter-based amplifier with the extended amplification period to enhance the output SNR. This paper occupies an active area of 0.01 mm² and achieves the Nyquist-rate signal-to-noise-and-distortion ratio (SNDR), spurious-free dynamic range (SFDR), Walden figure-of-merit (FoMW), and Schreier FoM (FoMS) of 64.1, 75.6 dB, 5.3 fJ/conversion step, and 172.8 dB, respectively.
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 249-252
A Calibration-Free 0.7-V 13-bit 10-MS/s Full-Analog SAR ADC with Continuous-Time Feedforward Cascaded (CTFC) Op-Amps
A calibration-free 13-bit 10-MS/s full-analog SAR ADC integrates the functions of comparator, SAR logic, and DAC switches into multiple inverter-based regenerative amplifiers (IRAs) to have a double timing budget for settling and relax the bandwidth requirement of analog circuits compared to the conventional SAR ADC. The continuous-time feedforward cascaded (CTFC) Op-amps are proposed to enhance the residue SNR using open-loop low gain-bandwidth amplifiers instead of closed-loop high-precision amplifiers. The prototype in 40nm CMOS occupies 0.013 mm 2 and achieves 67.6 dB SNDR 77.2 dB SFDR 3.2 fJ/conv.-step FoMw, and 176.6 dB FoMs without any calibration.
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 249-252
A Calibration-Free 0.7-V 13-bit 10-MS/s Full-Analog SAR ADC with Continuous-Time Feedforward Cascaded (CTFC) Op-Amps
A calibration-free 13-bit 10-MS/s full-analog SAR ADC integrates the functions of comparator, SAR logic, and DAC switches into multiple inverter-based regenerative amplifiers (IRAs) to have a double timing budget for settling and relax the bandwidth requirement of analog circuits compared to the conventional SAR ADC. The continuous-time feedforward cascaded (CTFC) Op-amps are proposed to enhance the residue SNR using open-loop low gain-bandwidth amplifiers instead of closed-loop high-precision amplifiers. The prototype in 40nm CMOS occupies 0.013 mm 2 and achieves 67.6 dB SNDR 77.2 dB SFDR 3.2 fJ/conv.-step FoMw, and 176.6 dB FoMs without any calibration.
- 10 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 65 (10) , 1365-1369
A 1-V 2.6-mW Environmental Compensated Fully Integrated Nose-on-a-Chip
Miniature gas detection system is desirable for many applications. In this study, we propose a fully integrated nose-on-a-chip for mobile phones and wearable devices. The chip has 36 on-chip sensors, a 36-channel adaptive interface with an integrated programmable amplifier, a four-channel frequency readout interface, one on-chip temperature sensor, a successive approximation analog-to-digital converter, a scalable learning kernel cluster, and a reduced instruction set computing core with low-voltage static random-access memory. This chip is fabricated using the TSMC 180-nm CMOS process and consumes 2.6 mW at 1 V. On-chip temperature and humidity sensors are included in this system for acquiring environmental information. An environmental compensation algorithm based on common principal components analysis (PCA) is also implemented for high-accuracy odor classification. This fully integrated nose-on-a-chip provides promising results for odor detection and classification for use in mobile and wearable device applications.
- 10 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 65 (10) , 1365-1369
A 1-V 2.6-mW Environmental Compensated Fully Integrated Nose-on-a-Chip
Miniature gas detection system is desirable for many applications. In this study, we propose a fully integrated nose-on-a-chip for mobile phones and wearable devices. The chip has 36 on-chip sensors, a 36-channel adaptive interface with an integrated programmable amplifier, a four-channel frequency readout interface, one on-chip temperature sensor, a successive approximation analog-to-digital converter, a scalable learning kernel cluster, and a reduced instruction set computing core with low-voltage static random-access memory. This chip is fabricated using the TSMC 180-nm CMOS process and consumes 2.6 mW at 1 V. On-chip temperature and humidity sensors are included in this system for acquiring environmental information. An environmental compensation algorithm based on common principal components analysis (PCA) is also implemented for high-accuracy odor classification. This fully integrated nose-on-a-chip provides promising results for odor detection and classification for use in mobile and wearable device applications.
- 12 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 53 (6) , 1755-1764
A 12-bit 150-MS/s Sub-Radix-3 SAR ADC With Switching Miller Capacitance Reduction
This paper presents a 0.9-V 1.5-mW 150-MS/s 12-bit successive-approximation-register analog-to-digital converter (SAR ADC) in 40-nm CMOS, which achieves a synergistic integration of multi-bit per cycle (M-bit/cycle) and sub-radix techniques with the comprehensive enhancement of speed and error tolerance. The proposed sub-radix-3 architecture uses a merged digital-to-analog converter (DAC) with a two-input comparator instead of the conventional separated DACs (signal and reference DACs) with a four-input comparator to effectively improve the matching performance and the power efficiency. Alternative-reference-switching (ARS) DACs are developed to reduce the total DAC effective switching capacitance by 47.4%. Offset injection technique is implemented to calibrate the comparator offset without the speed and power penalty by eliminating the additional output loading of capacitor array or the extra input pair. The SAR logic of each conversion cycle is simplified into one single tri-latch current mode logic (CML) to directly control the DAC switches which effectively reduces the SAR delay by 2/3. The achieved peak signal to noise and distortion ratio (SNDR), spurious-free dynamic range (SFDR), and Walden FoM are 61.7 dB, 74.4 dB, and 10.3-fJ/conversion-step, respectively.
- 12 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 53 (6) , 1755-1764
A 12-bit 150-MS/s Sub-Radix-3 SAR ADC With Switching Miller Capacitance Reduction
This paper presents a 0.9-V 1.5-mW 150-MS/s 12-bit successive-approximation-register analog-to-digital converter (SAR ADC) in 40-nm CMOS, which achieves a synergistic integration of multi-bit per cycle (M-bit/cycle) and sub-radix techniques with the comprehensive enhancement of speed and error tolerance. The proposed sub-radix-3 architecture uses a merged digital-to-analog converter (DAC) with a two-input comparator instead of the conventional separated DACs (signal and reference DACs) with a four-input comparator to effectively improve the matching performance and the power efficiency. Alternative-reference-switching (ARS) DACs are developed to reduce the total DAC effective switching capacitance by 47.4%. Offset injection technique is implemented to calibrate the comparator offset without the speed and power penalty by eliminating the additional output loading of capacitor array or the extra input pair. The SAR logic of each conversion cycle is simplified into one single tri-latch current mode logic (CML) to directly control the DAC switches which effectively reduces the SAR delay by 2/3. The achieved peak signal to noise and distortion ratio (SNDR), spurious-free dynamic range (SFDR), and Walden FoM are 61.7 dB, 74.4 dB, and 10.3-fJ/conversion-step, respectively.