Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Sergey Alekseyevich Zelepugin has a total of 65 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Fracture model of an AZ31 magnesium alloy under dynamic loading

    by S. A. Zelepugin, V. A. Skripnyak, A. E. Kirushkin


  • Impact energy absorption in 3D printed bio-inspired PLA structures

    by N.V. Kazantseva, A.O. Onishchenko, S.A. Zelepugin, R.O. Cherepanov, O.V. Ivanova


  • Mathematical Model of Shock-Induced Chemical Reactions

    by Roman O. Cherepanov, Oksana V. Ivanova, Sergey A. Zelepugin

  • Open Access

    Optimization of Johnson–Cook Constitutive Model Parameters Using the Nesterov Gradient-Descent Method

    by Sergey A. Zelepugin, Roman O. Cherepanov, Nadezhda V. Pakhnutova

    Numerical simulation of impact and shock-wave interactions of deformable solids is an urgent problem. The key to the adequacy and accuracy of simulation is the material model that links the yield strength with accumulated plastic strain, strain rate, and temperature. A material model often used in engineering applications is the empirical Johnson–Cook (JC) model. However, an increase in the impact velocity complicates the choice of the model constants to reach agreement between numerical and experimental data. This paper presents a method for the selection of the JC model constants using an optimization algorithm based on the Nesterov gradient-descent method. A solution quality function is proposed to estimate the deviation of calculations from experimental data and to determine the optimum JC model parameters. Numerical calculations of the Taylor rod-on-anvil impact test were performed for cylindrical copper specimens. The numerical simulation performed with the optimized JC model parameters was in good agreement with the experimental data received by the authors of this paper and with the literature data. The accuracy of simulation depends on the experimental data used. For all considered experiments, the calculation accuracy (solution quality) increased by 10%. This method, developed for selecting optimized material model constants, may be useful for other models, regardless of the numerical code used for high-velocity impact simulations.


  • Open Access

    Experimental Study of the Microhardness and Microstructure of a Copper Specimen Using the Taylor Impact Test

    by Sergey A. Zelepugin, Nadezhda V. Pakhnutova, Olga A. Shkoda, Evgenii N. Boyangin

    One commonly used method for characterizing the dynamic characteristics of materials is the Taylor impact test. This method measures the dynamic yield strength of cylindrical specimens and determines material model constants required for the numerical simulation of the behavior of materials subjected to high-velocity deformation. The purpose of this work is to investigate the microhardness and microstructure of copper specimens at different impact velocities using the Taylor impact test. This paper describes experiments performed on copper specimens (OFHC 99.9%, M1) using a single-stage light-gas gun with impact velocities in the range of 150–450 m/s. After impact, the specimens were cut along the symmetry axis to measure the microhardness and the grain size of the microstructure. Microhardness in the entire area exceeded the initial value for all investigated velocities. The averaged microhardness curves were obtained for each specimen to identify four deformation zones and determine their dimensions depending on the impact velocity. The average grain size in the entire deformed specimen became smaller than in the starting specimen. The study of the microstructure of the specimens has shown that the grain size distribution corresponds to the four deformation zones in the copper specimens.


  • Open Access

    Microhardness and Dynamic Yield Strength of Copper Samples upon Impact on a Rigid Wall

    by N. V. Pakhnutova, E. N. Boyangin, O. A. Shkoda, S. A. Zelepugin

    Introduction. One of the commonly used methods for assessing the dynamic characteristics of a material is the Taylor test, which establishes the relationship between the dynamic yield strength of a cylindrical sample material and its length after hitting a non-deformable barrier. The purpose of this work was to study the microhardness and determine the dynamic yield strength of copper samples for various impact velocities in the Taylor test.Materials and Methods. Experiments were carried out with cylindrical copper (M1) samples. The throwing conditions were selected on the ballistic stand, which provided the speed of the sample in the range of 150–450 m/s at the exit from the barrel. After the impact, the microhardness of the samples in the section plane was measured. The calculation of the dynamic yield strength was carried out according to the classical Taylor formula.Results. Experimental data are presented for cylindrical copper samples upon impact on a rigid wall with velocities in the range of 162–416 m/s, including configurations and sizes of images before and after impact. Microhardness distributions in the axial section of the samples were obtained. For each sample, the dependences of the averaged values of microhardness were constructed, which made it possible to identify four areas of deformation of the samples (the area of elastic deformations, plastic deformations, intense plastic deformations, the area of the material undergoing destruction) and determine their sizes. The dynamic yield strength of copper in the studied range of impact velocities was calculated.Discussion and Conclusions. The values of microhardness in the entire considered region and for all studied impact velocities exceeded the initial value. There was a significant increase in the value of the dynamic yield strength compared to its static value. The correlation of the maximum averaged values of microhardness and dynamic yield strength, which grew with increasing impact velocity, was identified.


  • Open Access

    Discrete One-Stage Mechanochemical Synthesis of Titanium-Nitride in a High-Energy Mill

    by Oleg Lapshin, Olga Shkoda, Oksana Ivanova, Sergey Zelepugin

    Discrete (discontinuous) mechanochemical synthesis of titanium nitride was experimentally investigated. The experimental results show that mechanical activation intensifies the chemical conversion in the Ti-N system, and the discrete synthesis of the final product is conducted under “soft” controlled conditions without high heat release. The new theory of mechanochemical synthesis and the mathematical model based on it were used for theoretical evaluation of the dynamics of titanium activation in the nitrogen medium. It was found that the discrete mode of synthesis includes two factors accelerating mechanochemical reactions in the Ti-N synthesis: structural (grinding of metallic reagent and formation of interfacial areas) and kinetic (accumulation of excess energy stored in the formed structural defects in metallic reagent). The kinetic constants of the process were found using experimental data and the inverse problem method. The diagrams defining the controlled modes of obtaining titanium nitride particles with the given characteristics were constructed. A mathematical model for theoretical estimation of the dynamics of activation of titanium powder in the nitrogen medium was developed using a new macrokinetic theory of mechanochemical synthesis.


  • NUMERICAL CALCULATION OF STRENGTH AND SHEAR RESISTANCE OF NON-RIGID ROAD PAVEMENT BY THE FINITE ELEMENT METHOD

    by D.V. Yanov, S.A. Zelepugin

    The paper presents 2D mathematical simulation results for a T–90 tank interacting with the III-type road in a plane-strain formulation. The purpose of the work is to determine the vertical deflection of an asphalt-concrete road, as well as the load factor of the two-layer road pavement (dense-graded asphalt concrete, open-graded asphalt concrete) and two-layer roadbed (gravel roadbed, ground roadbed – silt sandy loam). To calculate the load factor of the road pavement, the ratio of the von Mises stress to the ultimate compression stress is used. To analyze the shear resistance of the roadbed, the modified Drucker-Prager strength criterion is utilized. The computed results reveal the maximum vertical deflection in the contact area of the tracks. In the same area, the load factor of the road pavement is 3–12, which indicates the high bearing capacity of the dense-graded asphalt concrete. Analysis of the shear resistance of the roadbed shows that irreversible deformations occur in the gravel base in the contact area of the tracks, which can lead to the subsidence of the coating, while the load factor for sandy loam is 3–10.