Hongwei Liang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hongwei Liang has a total of 427 co-authors. Here are the top co-authors by number of shared publications:
Yang Liu
Dalian University of Technology
41 shared publicationsXiaochuan Xia
The School of Integrated Circuits, Dalian University of Technology 1 , Dalian 116024
33 shared publications- Xiaochuan Xia
Dalian University of Technology
30 shared publications Guotong Du
State Key Laboratory of Integrated Optoelectronics, College of Electronic Science and Engineering, Jilin University, Changchun 130012, China
29 shared publicationsRensheng Shen
School of Integrated Circuits, Dalian University of Technology 1 , Dalian 116024
22 shared publicationsYingmin Luo
School of Microelectronics, Dalian University of Technology, Dalian 116024, China
18 shared publications
Latest Publications
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 73 (11) , 4218-4226
Geant4-to-TCAD Multi-Bin Energy-Deposition Mapping for Transient Response Simulation of Silicon PIN β-Particle Detectors
- 1 November 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 73 (11) , 4218-4226
Geant4-to-TCAD Multi-Bin Energy-Deposition Mapping for Transient Response Simulation of Silicon PIN β-Particle Detectors
- 22 October 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (42) , 425914
Electromechanical activation and tracking of a high-order surface/interface-localized acoustic branch in Al-substituted h-BN/Al 2 O 3
High-order guided acoustic branches in layered film/substrate structures can operate at GHz frequencies. Their use in devices requires electrical excitation, continuity of the selected branch, and a corresponding response in a finite structure. Elastic, piezoelectric, dielectric, and density parameters calculated from first principles were used in a two-dimensional periodic unit-cell model and a finite cross-sectional two-port model of Al-substituted h-BN/Al 2 O 3 . For the representative 12.5% C5 Al-substituted configuration, the periodic model yields f r = 1.2997 GHz , corresponding to a maximum K eff 2 = 6.63 % at h = 1.90 μ m . The resonance–antiresonance pair disappears in a matched e i j = 0 control, showing that this electrical response requires nonzero piezoelectric coupling. Complex-field overlap, refined thickness sampling, and reverse tracking identify a consistent continuation of the branch across the sampled thickness range. Its surface/interface localization, sagittal-plane polarization, and intrafilm sign reversal, assessed together with direction-specific sapphire bulk-wave references and depth-resolved mechanical-power analysis, are consistent with a Sezawa-related high-order branch. The finite two-port model gives a normalized transmission maximum of −9.19 dB at 1.3488 GHz, compared with a pristine-h-BN background near −39.7 dB. Together, the piezoelectric control and the agreement in field topology link substitution-induced material changes to electrical activation and the corresponding finite-model acoustic transmission.
- 22 October 2026
- Published by IOP Publishing in Physica Scripta
- Vol. 101 (42) , 425914
Electromechanical activation and tracking of a high-order surface/interface-localized acoustic branch in Al-substituted h-BN/Al 2 O 3
High-order guided acoustic branches in layered film/substrate structures can operate at GHz frequencies. Their use in devices requires electrical excitation, continuity of the selected branch, and a corresponding response in a finite structure. Elastic, piezoelectric, dielectric, and density parameters calculated from first principles were used in a two-dimensional periodic unit-cell model and a finite cross-sectional two-port model of Al-substituted h-BN/Al 2 O 3 . For the representative 12.5% C5 Al-substituted configuration, the periodic model yields f r = 1.2997 GHz , corresponding to a maximum K eff 2 = 6.63 % at h = 1.90 μ m . The resonance–antiresonance pair disappears in a matched e i j = 0 control, showing that this electrical response requires nonzero piezoelectric coupling. Complex-field overlap, refined thickness sampling, and reverse tracking identify a consistent continuation of the branch across the sampled thickness range. Its surface/interface localization, sagittal-plane polarization, and intrafilm sign reversal, assessed together with direction-specific sapphire bulk-wave references and depth-resolved mechanical-power analysis, are consistent with a Sezawa-related high-order branch. The finite two-port model gives a normalized transmission maximum of −9.19 dB at 1.3488 GHz, compared with a pristine-h-BN background near −39.7 dB. Together, the piezoelectric control and the agreement in field topology link substitution-induced material changes to electrical activation and the corresponding finite-model acoustic transmission.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 16 (10) , 2417-2422
Enhanced Stability in TOSA via Thermistor-on-Chip and Bridge-Pad Wire-Bonding Design
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Components, Packaging and Manufacturing Technology
- Vol. 16 (10) , 2417-2422
Enhanced Stability in TOSA via Thermistor-on-Chip and Bridge-Pad Wire-Bonding Design
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (18) , 27238-27244
A Localization Method for Alpha Particle 1-D Position in Diamond Detectors
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (18) , 27238-27244
A Localization Method for Alpha Particle 1-D Position in Diamond Detectors
- 24 August 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (8)
High mobility p -type doping of hexagonal boron nitride films on diamond (100) substrates
The heteroepitaxy of hexagonal boron nitride (h-BN) on diamond exhibits significant potential for the advancement of diamond-based electronic devices. p-Type doping of h-BN is expected to provide sufficient carriers for forming a two-dimensional hole gas at the diamond interfaces. However, high-mobility doping of h-BN remains challenging. Here, we report the in situ growth of magnesium-doped h-BN films on single-crystal diamond (100) substrates using radio frequency magnetron sputtering, followed by an annealing treatment in the same vacuum chamber. The resultant h-BN films exhibit dense and atomically smooth surfaces with roughness below 1 nm, as well as uniform doping profiles within the films. Both x-ray photoelectron spectroscopy and secondary ion mass spectroscopy reveal the presence of Mg–N bonds, suggesting the successful incorporation of Mg atoms. The successive annealing treatment after growth further improved the activation efficiency of the dopants. Hall effect measurements revealed distinct p-type conductivity, with hole mobility increasing to 222 cm2/V s and resistivity decreasing by over three orders of magnitude. These results demonstrate an effective and feasible route for achieving high-mobility p-type h-BN films directly on diamond substrates, which are essential for developing high-performance diamond-based electronics.
- 24 August 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (8)
High mobility p -type doping of hexagonal boron nitride films on diamond (100) substrates
The heteroepitaxy of hexagonal boron nitride (h-BN) on diamond exhibits significant potential for the advancement of diamond-based electronic devices. p-Type doping of h-BN is expected to provide sufficient carriers for forming a two-dimensional hole gas at the diamond interfaces. However, high-mobility doping of h-BN remains challenging. Here, we report the in situ growth of magnesium-doped h-BN films on single-crystal diamond (100) substrates using radio frequency magnetron sputtering, followed by an annealing treatment in the same vacuum chamber. The resultant h-BN films exhibit dense and atomically smooth surfaces with roughness below 1 nm, as well as uniform doping profiles within the films. Both x-ray photoelectron spectroscopy and secondary ion mass spectroscopy reveal the presence of Mg–N bonds, suggesting the successful incorporation of Mg atoms. The successive annealing treatment after growth further improved the activation efficiency of the dopants. Hall effect measurements revealed distinct p-type conductivity, with hole mobility increasing to 222 cm2/V s and resistivity decreasing by over three orders of magnitude. These results demonstrate an effective and feasible route for achieving high-mobility p-type h-BN films directly on diamond substrates, which are essential for developing high-performance diamond-based electronics.
- 24 August 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
Highly Anisotropic Quasi-1D δ-CsPbI3 Single Nanowire Decorated with Au Nanoparticles for Polarization-Sensitive Photodetection
The development of polarization-sensitive photodetectors based on low-dimensional materials with intrinsic lattice anisotropy has paved the way for next-generation polarizer-free and integration-friendly polarization-sensitive optoelectronic devices. Despite their superiority in miniaturization, the relatively low dichroic ratios (DRs) hinder further industrialization. In this work, low-dimensional derivatives of perovskite, quasi-1D yellow-phase (δ-phase) CsPbI3 single nanowires (NWs) are investigated for polarization-sensitive photodetection. Aberration-corrected transmission electron microscopy (TEM) and angle-resolved polarized Raman spectroscopy (ARPRS) reveal the pronounced crystallographic anisotropy of δ-CsPbI3. The pristine δ-CsPbI3 single NW photodetector exhibits a large DR of up to 8.3 under 405 nm illumination. To overcome the limited optoelectronic performance arising from the indirect bandgap nature of δ-CsPbI3, localized surface plasmon resonance (LSPR) is introduced by decorating the δ-CsPbI3 single NW with Au nanoparticles (NPs) via thermal evaporation. The Au-decorated device exhibits up to approximately 9-fold photocurrent enhancement compared with the pristine one, achieving a photoresponsivity (R) of 5.3 mA W–1 and a specific detectivity (D*) of 1.1 × 1010 Jones while retaining the high polarization sensitivity. In addition, the Au-decorated device demonstrates appreciable operational stability under ambient conditions, preserving 92% of its initial photocurrent after 400 switching cycles. This work unveils the great potential of the δ-CsPbI3 single NW for polarized light detection and demonstrates the feasibility of Au NP decoration regarding optoelectronic performance optimization, which can potentially be extended to other low-dimensional perovskite derivatives with analogous quasi-1D chain lattices.
- 24 August 2026
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
Highly Anisotropic Quasi-1D δ-CsPbI3 Single Nanowire Decorated with Au Nanoparticles for Polarization-Sensitive Photodetection
The development of polarization-sensitive photodetectors based on low-dimensional materials with intrinsic lattice anisotropy has paved the way for next-generation polarizer-free and integration-friendly polarization-sensitive optoelectronic devices. Despite their superiority in miniaturization, the relatively low dichroic ratios (DRs) hinder further industrialization. In this work, low-dimensional derivatives of perovskite, quasi-1D yellow-phase (δ-phase) CsPbI3 single nanowires (NWs) are investigated for polarization-sensitive photodetection. Aberration-corrected transmission electron microscopy (TEM) and angle-resolved polarized Raman spectroscopy (ARPRS) reveal the pronounced crystallographic anisotropy of δ-CsPbI3. The pristine δ-CsPbI3 single NW photodetector exhibits a large DR of up to 8.3 under 405 nm illumination. To overcome the limited optoelectronic performance arising from the indirect bandgap nature of δ-CsPbI3, localized surface plasmon resonance (LSPR) is introduced by decorating the δ-CsPbI3 single NW with Au nanoparticles (NPs) via thermal evaporation. The Au-decorated device exhibits up to approximately 9-fold photocurrent enhancement compared with the pristine one, achieving a photoresponsivity (R) of 5.3 mA W–1 and a specific detectivity (D*) of 1.1 × 1010 Jones while retaining the high polarization sensitivity. In addition, the Au-decorated device demonstrates appreciable operational stability under ambient conditions, preserving 92% of its initial photocurrent after 400 switching cycles. This work unveils the great potential of the δ-CsPbI3 single NW for polarized light detection and demonstrates the feasibility of Au NP decoration regarding optoelectronic performance optimization, which can potentially be extended to other low-dimensional perovskite derivatives with analogous quasi-1D chain lattices.
- 1 August 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (16) , 23935-23940
Laser-Induced Gettering Enables Substrate-Free 4H-SiC Radiation Detectors
- 1 August 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (16) , 23935-23940
Laser-Induced Gettering Enables Substrate-Free 4H-SiC Radiation Detectors
- Open Access
- 30 July 2026
- Published by Wiley in Advanced Science
- Vol. 13 (60) , e76923
Porous Ultralow‐ κ sp 2 ‐Bonded Boron Nitride Thin Films as Copper Diffusion Barriers
Dielectric materials with low dielectric constant ( κ < 2) are highly needed to overcome a series of problems caused by the decreasing size of microelectronics. An effective way to reduce dielectric constant is introducing void structure in dielectric materials, however challenging in mechanical strength and wetting properties. Herein, porous sp 2 ‐bonded boron nitride (BN) films are directly grown on Si substrates via radio frequency magnetron sputtering. The Guinier plot analysis of grazing incidence small‐angle X‐ray scattering spectra and electron microscopy confirms the pore size of ∼1.85 nm. The porous BN (p‐BN) films show a band gap of ∼5.88 eV and a hydrophobic surface, ensuring the stability of dielectric properties. P‐BN films exhibit an ultralow‐ κ of 1.77 at 100 kHz. These porous ultralow‐ κ BN films are electrically robust and mechanically stable superior to the previously reported porous dielectrics and close to the referent dense amorphous BN and hexagonal BN. Additionally, the p‐BN films demonstrate notable diffusion barrier capability, effectively blocking Cu diffusion even with a thickness as low as 3 nm. This work provides a viable approach towards the controlled synthesis of porous ultralow‐ κ BN films as versatile dielectrics for transistor gate barriers, passivation layers, and capacitor spacers in high‐performance electronics.
- 30 July 2026
- Published by Wiley in Advanced Science
- Vol. 13 (60) , e76923
Open AccessPorous Ultralow‐ κ sp 2 ‐Bonded Boron Nitride Thin Films as Copper Diffusion Barriers
Dielectric materials with low dielectric constant ( κ < 2) are highly needed to overcome a series of problems caused by the decreasing size of microelectronics. An effective way to reduce dielectric constant is introducing void structure in dielectric materials, however challenging in mechanical strength and wetting properties. Herein, porous sp 2 ‐bonded boron nitride (BN) films are directly grown on Si substrates via radio frequency magnetron sputtering. The Guinier plot analysis of grazing incidence small‐angle X‐ray scattering spectra and electron microscopy confirms the pore size of ∼1.85 nm. The porous BN (p‐BN) films show a band gap of ∼5.88 eV and a hydrophobic surface, ensuring the stability of dielectric properties. P‐BN films exhibit an ultralow‐ κ of 1.77 at 100 kHz. These porous ultralow‐ κ BN films are electrically robust and mechanically stable superior to the previously reported porous dielectrics and close to the referent dense amorphous BN and hexagonal BN. Additionally, the p‐BN films demonstrate notable diffusion barrier capability, effectively blocking Cu diffusion even with a thickness as low as 3 nm. This work provides a viable approach towards the controlled synthesis of porous ultralow‐ κ BN films as versatile dielectrics for transistor gate barriers, passivation layers, and capacitor spacers in high‐performance electronics.
- 13 June 2026
- Published by Wiley in Advanced Optical Materials
Strain Induced Bandgap Engineering in Wafer‐Scale Hexagonal Boron Nitride Thick Epitaxial Films for Broadband Solar‐Blind Ultraviolet Detection
The Earth's atmosphere selectively intercepts ultraviolet (UV) light, endowing solar‐blind UV (Solar blind, 200–280 nm) detection with low interference and a low false alarm rate, which is irreplaceable in multiple fields. Hexagonal boron nitride ( h ‐BN), an ultra‐wide bandgap semiconductor, is an ideal solar blind detection material but is limited by a fixed intrinsic bandgap and poor thickness tunability. Herein, we achieved heteroepitaxial growth of 2‐inch h ‐BN films (several nm–2 µm) on sapphire via low‐temperature plasma‐enhanced chemical vapor deposition (PECVD). Thickness accumulation induces in‐plane compressive and out‐of‐plane tensile strains, narrowing the h ‐BN bandgap from 5.72 to 4.87 eV. Density functional theory (DFT) calculations confirm that the bandgap variation is dominated by the conduction band minimum (Γ point) shift, as it is highly sensitive to biaxial compressive and tensile strains, unlike the valence band maximum (M point). The fabricated metal‐semiconductor‐metal (MSM) photodetectors cover the range from 185 to 280 nm with pA‐level dark current, high responsivity, and excellent high‐temperature/long‐term stability. This work breaks through the traditional bottleneck in h ‐BN bandgap engineering via thickness‐mediated stress variation, providing a novel strategy and experimental foundation for the large‐scale fabrication of high‐performance full‐band solar blind photodetectors.
- 13 June 2026
- Published by Wiley in Advanced Optical Materials
Strain Induced Bandgap Engineering in Wafer‐Scale Hexagonal Boron Nitride Thick Epitaxial Films for Broadband Solar‐Blind Ultraviolet Detection
The Earth's atmosphere selectively intercepts ultraviolet (UV) light, endowing solar‐blind UV (Solar blind, 200–280 nm) detection with low interference and a low false alarm rate, which is irreplaceable in multiple fields. Hexagonal boron nitride ( h ‐BN), an ultra‐wide bandgap semiconductor, is an ideal solar blind detection material but is limited by a fixed intrinsic bandgap and poor thickness tunability. Herein, we achieved heteroepitaxial growth of 2‐inch h ‐BN films (several nm–2 µm) on sapphire via low‐temperature plasma‐enhanced chemical vapor deposition (PECVD). Thickness accumulation induces in‐plane compressive and out‐of‐plane tensile strains, narrowing the h ‐BN bandgap from 5.72 to 4.87 eV. Density functional theory (DFT) calculations confirm that the bandgap variation is dominated by the conduction band minimum (Γ point) shift, as it is highly sensitive to biaxial compressive and tensile strains, unlike the valence band maximum (M point). The fabricated metal‐semiconductor‐metal (MSM) photodetectors cover the range from 185 to 280 nm with pA‐level dark current, high responsivity, and excellent high‐temperature/long‐term stability. This work breaks through the traditional bottleneck in h ‐BN bandgap engineering via thickness‐mediated stress variation, providing a novel strategy and experimental foundation for the large‐scale fabrication of high‐performance full‐band solar blind photodetectors.
- 4 June 2026
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 18 (26) , 14116-14124
Decay-length-guided electrode spacing for wide-linear-dynamic-range CsPbBr 3 nanowire photodetectors
A decay-length-guided electrode-spacing design is proposed for CsPbBr 3 nanowire photodetectors, balancing carrier collection and contact-field effects to achieve high linear dynamic range at micro-/nanoscale dimensions.
- 4 June 2026
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 18 (26) , 14116-14124
Decay-length-guided electrode spacing for wide-linear-dynamic-range CsPbBr 3 nanowire photodetectors
A decay-length-guided electrode-spacing design is proposed for CsPbBr 3 nanowire photodetectors, balancing carrier collection and contact-field effects to achieve high linear dynamic range at micro-/nanoscale dimensions.