HHHuimin He

Huimin He

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Huimin He has a total of 48 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Simulation and experimental investigation of liquid-cooling thermal management for high-bandwidth co-packaged optics

    by Senhan Wu, Song Wen, Huimin He, Jianyu Feng, Chuan Chen, Haiyun Xue

    This study explores the application of cold plate liquid cooling technology in co-packaged optics (CPO). By integrating optical modules and the switch chip on the same substrate, CPO shortens the electrical interconnection distance, effectively solving the problems of high power consumption and poor signal integrity of traditional pluggable optical modules under high bandwidth. However, the surge in power density and the thermal crosstalk resulting from high integration density make thermal management one of the key challenges that constrain the reliability of high-capacity co-packaged optics. For the unique architecture of CPO, this study analyzes its heat dissipation needs in detail, and a thermal management scheme is designed. The thermal management scheme is simulated and optimized based on the Navier−Stokes equation. The simulation results show that, in a 51.2 Tbit/s CPO system, the junction temperature of the switch chip is 97.3 °C, the maximum junction temperature of the optical modules is 31.3 °C, and the temperature difference between the optical modules is 2.4 °C to 1.2 °C. To verify the simulation results, a thermal test experimental platform is built, and the experimental results show that the temperature simulation difference is within 4% and the pressure change trend is consistent with the simulation. Combining the experimental data and simulation results, the designed heat sink can satisfy the heat dissipation demands of the 51.2 Tbit/s bandwidth CPO system. This conclusion demonstrates the potential of liquid-cooling technology in CPO, providing support for research on liquid-cooling technology in the CPO. The design provides a theoretical and practical basis for the high performance and reliability of optoelectronic integration technology in wavelength division multiplexing (WDM) systems and micro-ring device applications, contributing to the application of next-generation optical communication networks. Graphical Abstract


  • Thermomechanical and Compression Analyses for Large-Scale Co-Packaged Optics (CPO) Assembly

    by Rui Cao, Huimin He, Fengze Hou, Rui Ma, Fengman Liu, Qidong Wang, Liqiang Cao

    With the development of artificial intelligence and other high-performance computing, the data transmission bandwidth in data centers has increased to 51.2 Tbps and will double every two years. The traditional pluggable optical modules have difficulty in satisfying the requirements. Co-packaged optics (CPO) integrates ASICs and optical engines (OEs) on the same substrate, providing a low energy loss and high throughput solution. However, the CPO structure is complicated and the package size is large. Therefore, the assembly-induced mechanical stresses and warpage of CPO are serious issues. In this paper, assembly feasibility based on a 200 × 200 mm 2 51.2 Tbps CPO was analyzed by a cross-scale simulation methodology with multiple mechanical stresses. First, the ASIC structure optimization of the CPO was carried out, and the CPO substrate was determined. Then, based on the above-optimized structure, the thermal reflow simulations of ASIC and mechanical compression simulations of OEs were conducted by the birth and death element method. The results showed that the stiffener ring in the ASIC package was optimized to be 3 mm in height and 15 mm in width. The 5 mm PCB was determined for the CPO substrate. The CPO substrate warpage under the socket after the thermal reflow was less than 0.05 mm and the maximum equivalent stresses of the BGA in the whole assembly process were less than the yield strength of the SAC305 by sub-model structure analysis. The socket terminal forces after mechanical compression were greater than 0.1 N. The analyzed results meet the process targets during the assembly of the CPO.


  • Challenges and Technologies of Frontside Via-Last Active-Interposer Processes on Low-k Material for 3-D Chiplet

    by Rui Cao, Huimin He, Lijun Chen, Chengyi Liao, Fengman Liu, Liqiang Cao, Qidong Wang

    3D chiplet technology based on TSV active interposer is an effective way to continue increasing integration, reducing power, and improving performance as Moore’s Law slows down. The TSV active interposer not only provides paths for die-to-die interconnections but also integrates logic functions. In this study, an active interposer fabrication technique for integrated TSVs was developed. The active interposer was successfully fabricated by the frontside via-last technology. However, due to the low-k material on the top side of the wafer, the process of the active interposer faces many challenges, including the TSV etching, the TSV cleaning, and the scribing of the low-k wafer. This work proposed the double-step protection method to avoid the over-etching of TSV due to the porous structure of the low-k material. Then, the 350 °C baking for one hour after the wafer cleaning method was proposed to avoid short-circuiting due to the water absorption characteristics of the low-k material. Besides, the blade saw followed by laser grooving method was proposed to avoid chipping and splattering of the wafer due to the low mechanical strength of the low-k material. Finally, the TSV active interposer was fabricated to conform with the design requirements and to satisfy the application of the 3D chiplet. The dimension of the active interposer was 22 mm × 20 mm. The main connection structures of the active interposer were fabricated by the back end of line (BEOL). The frontside contained the TSVs (10 μm × 100 μm), 3 metal layers, and micro-bumps with 26.2 μm diameter and 18.8 μm height. The backside contained 1 metal layer and C4 bumps with 77.6 μm diameter and 77.3 μm height. The survival rate of the sample is about 89% after the 200 cycles thermal cycling test, from -40 °C to 125 °C.


  • Enhanced Fabrication and Assembly of 3-D Chiplets Based on Active Interposer With Frontside Via-Last TSVs

    by Chengyi Liao, Huimin He, Fengman Liu, Xugang Wang, Rui Cao, Lijun Chen, Cheng Peng, Liqiang Cao, Qingdong Wang

    The development of semiconductors, driven by artificial intelligence (AI) and fifth-generation technology (5G) technologies, has posed challenges in advanced packaging. To address these challenges, a 3D packaging architecture based on active interposers has emerged. This paper presents novel fabrication method of active interposer with high-aspect-ratio through silicon vias (TSVs) and reliable assembly process of 3D chiplets. The proposed fabrication method of active interposer adopts frontside via-last TSV technology. Firstly, a two-step protection method etching is implemented to address low-dielectric constant (low-k) material over-etching risks. Then baking at 350 °C after TSV etching is suggested to prevent short circuits. Lastly, a blade saw followed by laser scribing is proposed to mitigate die chipping during the dicing saw of low-k material. Additionally, the 3D chiplet assembly process is optimized for low-thickness, large-area active interposer-to-substrate and high-density-I/O die-to-die bonding. Optimized recipe of thermal compression bonding (TCB), along with solder on pad (SoP), modified under-bump-metallization (UBM) and novel flux transfer method, ensures high-quality solder joints without voids or bridging. The validity of the optimized assembly process is confirmed by reliability tests. The successfully integrated 3D chiplets demonstrate that the fabrication process of active interposer and the optimized assembly flow can enhance the performance and reliability of 3D chiplet packaging in various applications.


  • Open Access

    High-Bandwidth Lumped Mach-Zehnder Modulators Based on Thin-Film Lithium Niobate

    by Peng Yang, Siwei Sun, Yuqiang Zhang, Rui Cao, Huimin He, Haiyun Xue, Fengman Liu

    Recently, lumped Mach-Zehnder Modulators (MZMs) have received renewed attention due to their potential for low power consumption and compact size. However, the practicality of lumped MZMs with conventional lumped electrodes (C−LEs) is limited by their lower electro−optical (EO) bandwidth. The reduction in EO bandwidth results from the inherent trade−off between EO bandwidth and half−wave voltage length product (VπL) within the C−LE architecture. This paper proposes a thin−film lithium niobate (TFLN)−based lumped MZM with capacitively−loaded lumped electrodes (CL−LEs). The purely linear EO effect of the LN eliminates the parasitic capacitance in the doped PN junction and enhances the EO bandwidth. Furthermore, the CL−LE structure can break the limitation between EO bandwidth and VπL inherent in the C−LE design. Simulations show the proposed device achieves a high EO bandwidth of 32.4 GHz and a low VπL of 1.15 V·cm. Due to the reduced capacitance and lower VπL, the power consumption of the device is as low as 0.1 pJ/bit. Simulation results indicate that the open−eye diagrams are achieved at 64 Gb/s for 1.5 mm TFLN lumped MZM, with an ER of 2.97 dB. Consequently, the proposed device architecture substantially enhances the performance of lumped MZMs, showing promise for application in short−reach optical interconnects within data centers.


  • Open Access

    Design, Manufacture and Assembly of 3D Integrated Optical Transceiver Module Based on an Active Photonic Interposer

    by Qi Zheng, Haiyun Xue, Fengman Liu, Liqiang Cao, Qidong Wang, Huimin He, Fengwei Dai, Peng Sun

    The new generation of data centers is further evolving towards the direction of high speed and intelligence, which puts forward a great demand for the iteration of optical interconnection technology. Three-dimensional integration based on active photonic interposers can achieve the advantages of high integration, high bandwidth and low power consumption, which has become the main direction for next generation optical module technology. The fabrication and assembly of 3D optical modules based on active interposer-integrated edge couplers and TSV are realized in this paper. Different active interposer processes with integrated edge couplers and RDL-TSV-RDL structures are discussed, manufactured, analyzed and evaluated. The problem of the co-fabrication of the TSV and edge coupler was solved, and perfect electrical and optical characteristics were also achieved. Finally, the fabrication of the substrate and the assembly of the 3D optical module were completed. This paper lays a solid foundation for the further research and large-scale application of 3D optical modules in the future.


  • A 4×52 Gbps PAM4 WDM Transmitter with Silicon Photonics Microring Modulator

    by Rui Cao, Huimin He, Fengman Liu, Liqiang Cao

    Optical transmitter is the carrier to realize optic communication. It is important to study the package design of high data rates optical transmitter and solve the engineering problems in the application of optical transmitter for optic communication. MRM-based wavelength division multiplexing (WDM) transmitter has become a hot topic because of the features of microring modulator (MRM). The development trend of MRM-based WDM transmitter is toward high density and high single-channel rate. In this paper, a 12-channel silicon photonics MRM-based WDM transmitter controlled by three CMOS drivers is designed. In addition, to increase the temperature stability of the MRM-based transmitter, a thermoelectric cooler (TEC) is introduced. Besides, high temperature co-fired ceramic (HTCC) is adopted in this study for hermetic encapsulation of TEC to ensure the high reliability of the TEC which could be impacted by the condensed water drop. After the carefully design and optimization, the WDM transmitter is fabricated. And four channels controlled by one of the drivers are measured. The results show that the 4-channel transmitter at 52 Gbps/ch PAM4 signals is obtained. And 12×52 Gbps PAM-4 signals transmission through a transmitter is potential.

  • Simulation and Optimization of the high-speed transmission structure in organic-packaged coherent optical transceiver

    by Jinteng Zhao, Huimin He, Haiyun Xue, Qi Zheng, Jian Yuan, Peng Yang, Rui Cao, Fengman Liu

    With the development of the data center, the appropriate packaging design of coherent optical module applied in data center is becoming more and more important. The coherent optical module with organic substrate could reduce the cost and increase the bandwidth. However, realizing the high-speed signal transmission on organic substrate is one of the bottlenecks in the whole transmission system of coherent module. In the transmission of high-speed signal, it is inevitable to meet the impedance discontinuities such as AC-coupled capacitors and holes. These impedance discontinuities seriously affect signal integrity. Therefore, this paper studies the compensation method for these impedance discontinuities. After the careful design and optimization, the results show that inductance compensation can effectively improve the transmission performance. The lowest insertion loss S21, is - 1.2dB, fully meeting the design requirements of 3dB, and the highest reflection loss S11, is less than -10dB. The maximum value of TDR is 101.5Ω, and the minimum value is 97 Ω.


  • Research on 3D Optical Module Integrating Edge Coupler and TSV

    by Qi Zheng, Peng Yang, Haiyun Xue, Huimin He, Rui Cao, Fengwei Dai, Siwei Sun, Fengman Liu, Qidong Wang, Liqiang Cao, et al.

    3D integration photonic interposer is becoming popular in the field of co-packaging optics (CPO). In this paper, we integrate the edge coupler and through silicon via (TSV) into the silicon interposer. Different high-frequency transmission lines are designed, analyzed and simulated. The measured results and the simulation have a good correspondence. The high frequency transmission lines, which consist of 10 μm × 100 μm TSVs and two redistribution layer (RDL) lines of 100 μm on the top layer and one 100 μm RDL line on the bottom layer, shows perfect insertion loss less than 0.35 dB @67 GHz. In addition, the 56GBaud (112Gbps) eye diagram is tested and shows excellent transmission quality. Edge couplers are designed and fabricated by packaging process. The coupling loss of coupler is less than 1.7 dB/facet. The 3D optical package module based on the active optical interposer has also been realized and verified.


  • Design and Realization of Multi-Channel and High-Bandwidth 2.5D Transmitter Integrated With Silicon Photonic MZM

    by Huimin He, Haiyun Xue, Yu Sun, Fengman Liu, Liqiang Cao

    Recently, the interconnection bandwidth of the data center is rapidly increasing. To satisfy the requirement for the high-performance data center, a 4-channel 2.5D silicon photonic transmitter is proposed and the packaging structure could increase the high-density scalability of the architecture for 1.6T/3.2T co-packaging optics (CPO) module. The electrical driver and silicon photonic Mach-Zehnder modulator (MZM) are mounted to the silicon interposer by the micro-bumps. Meanwhile, the silicon interposer is mounted to the low temperature co-fired ceramic by the solder balls. The 2.5D transmitter is assembled to the motherboard by the high-speed ball grid array (BGA) connector to make it convenient to be replaced. The electrical optimization is implemented to make the insertion loss of the whole passive link within −1.55 dB under 40 GHz, which ensures the transmitter with the socket transmit the clear simulated eye diagram at 64 Gbps PAM4 rate per channel. Moreover, the thermal evaluation is performed, which includes the heat- dissipation evaluation and the thermal-induced impact on the edge light coupling. Finally, the substrates in the 2.5D transmitter are fabricated and the transmitter is realized by the improved assembly method. By the verification of the measurement, the 2.5D transmitter we proposed could work at 64 Gbps PAM4 signal transmission rate per channel with the 6pJ/bit power consumption. Regardless of the bandwidth of the electronic integrated circuit (EIC)/MZM and the BGA connector, based on the simulation electrical bandwidth, it is potential for realizing 100 Gbps PAM4 signal transmission.