Pablo Rodriguez-Calvillo
Research Subjects
Pablo Rodriguez-Calvillo has a total of 116 co-authors. Here are the top co-authors by number of shared publications:
Yvan Houbaert
14 shared publications- Jose Maria Cabrera
Department of Materials Science and Engineering, Campus Diagonal Besòs-EEBE, Universitat Politècnica de Catalunya-BarcelonaTech, 08019 Barcelona, Spain
12 shared publications Y. Houbaert
Department of Materials Science and Engineering, Ghent University 3 , Technologiepark 903, B-9052 Gent-Zwijnaarde
8 shared publications- Roumen Petrov
MST-DyMaLab Research Group, Department of Electromechanical, Systems and Metal Engineering, Ghent University, Tech Lane Ghent Science Park 46, 9052 Zwijnaarde, Belgium
5 shared publications D. Segers
4 shared publicationsJ. De Baerdemaeker
4 shared publications
Latest Publications
- Open Access
EBSD Study of Delta-Processed Ni-Based Superalloy
Nickel-based superalloys are extensively used in the aerospace and power generation industries due to their excellent mechanical properties at elevated temperatures and good corrosion resistance. Typically, these alloys require accomplishing critical standards during their manufacturing process. In this study, an Inconel 718 (IN718) Ni-based superalloy was subjected to a delta-processing treatment (DP718) and subsequently deformed at high temperature. Samples were compressed below and above the δ-solvus temperature at two different strain rates of 0.001 s−1 and 0.01 s−1. A detailed microstructural characterization was carried out by the electron backscattered diffraction technique (EBSD). Kikuchi patterns and the orientation relationship of the δ-phase were identified. For samples deformed above the δ-solvus at 0.01 s−1, an increase in the percentage of low angle grain boundaries (LAGB) within deformed grains and a decrease in high angle grain boundaries (HAGB) were observed. Comprehensive observation of the microstructural evolution of IN718 subjected to DP718 using orientation map images was also performed.
Open AccessEBSD Study of Delta-Processed Ni-Based Superalloy
Nickel-based superalloys are extensively used in the aerospace and power generation industries due to their excellent mechanical properties at elevated temperatures and good corrosion resistance. Typically, these alloys require accomplishing critical standards during their manufacturing process. In this study, an Inconel 718 (IN718) Ni-based superalloy was subjected to a delta-processing treatment (DP718) and subsequently deformed at high temperature. Samples were compressed below and above the δ-solvus temperature at two different strain rates of 0.001 s−1 and 0.01 s−1. A detailed microstructural characterization was carried out by the electron backscattered diffraction technique (EBSD). Kikuchi patterns and the orientation relationship of the δ-phase were identified. For samples deformed above the δ-solvus at 0.01 s−1, an increase in the percentage of low angle grain boundaries (LAGB) within deformed grains and a decrease in high angle grain boundaries (HAGB) were observed. Comprehensive observation of the microstructural evolution of IN718 subjected to DP718 using orientation map images was also performed.
- 1 August 2019
- Published by Elsevier in Acta Materialia
- Vol. 174, 92-104
A multi-scale study of the interaction of Sn solutes with dislocations during static recovery in α-Fe
- 1 August 2019
- Published by Elsevier in Acta Materialia
- Vol. 174, 92-104
A multi-scale study of the interaction of Sn solutes with dislocations during static recovery in α-Fe
- 1 May 2019
- Published by ASTM International in Materials Performance and Characterization
- Vol. 8 (5) , 985-999
Effect of Silicon on the Hot Flow Behavior of Ultra-Low Carbon Austenite
The influence of silicon on the high-temperature deformation behavior of ultra-low carbon austenite was studied in the range of temperature and strain rate from 1,000 to 1,100°C and 0.001 to 0.1 s−1, respectively. The flow curves of the steels exhibit the classic softening due to dynamic recrystallization. The characteristic pairs of stress-strain values (zero, critical, peak, saturation, and steady state) were determined by the analysis of the work hardening curves. These values were analyzed by applying first the classical Sellars and McTegart approach. Once the apparent stress exponents and activation energies were determined as being in the vicinity of 5 and above 270 kJ/mol, respectively, a modified hyperbolic sine equation was used. The flow curves were characterized by work hardening, dynamic recovery, and recrystallization terms at any processing conditions, showing a direct relationship with the silicon content of the steels. Finally, all the flow curves of studied steels were discussed and modeled as a function of the processing parameters and silicon content.
- 1 May 2019
- Published by ASTM International in Materials Performance and Characterization
- Vol. 8 (5) , 985-999
Effect of Silicon on the Hot Flow Behavior of Ultra-Low Carbon Austenite
The influence of silicon on the high-temperature deformation behavior of ultra-low carbon austenite was studied in the range of temperature and strain rate from 1,000 to 1,100°C and 0.001 to 0.1 s−1, respectively. The flow curves of the steels exhibit the classic softening due to dynamic recrystallization. The characteristic pairs of stress-strain values (zero, critical, peak, saturation, and steady state) were determined by the analysis of the work hardening curves. These values were analyzed by applying first the classical Sellars and McTegart approach. Once the apparent stress exponents and activation energies were determined as being in the vicinity of 5 and above 270 kJ/mol, respectively, a modified hyperbolic sine equation was used. The flow curves were characterized by work hardening, dynamic recovery, and recrystallization terms at any processing conditions, showing a direct relationship with the silicon content of the steels. Finally, all the flow curves of studied steels were discussed and modeled as a function of the processing parameters and silicon content.
- Open Access
- 26 July 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 98 (9-12) , 2917-2932
Thermal stability of ARMCO iron processed by ECAP
- 26 July 2018
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 98 (9-12) , 2917-2932
Open AccessThermal stability of ARMCO iron processed by ECAP
- Open Access
- 18 June 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 375 (1) , 012016
Segregation affecting the evolution of primary recrystallization textures in a ternary Fe-Si-Sn alloy
The effect of Sn addition on the primary recrystallization of cold rolled Fe-3 wt. % Si alloys is investigated. Texture evolution and misorientation distributions are analyzed on partially recrystallized samples using the electron backscatter diffraction technique (EBSD). Sn was found to affect the microstructure, throughout the thermal treatment of the materials, by refining the grains and altering the texture. In the presence of Sn, the intensity of {111}<uvw> grains is reduced through all stages of recrystallization, while that of {100}<uvw> and {hkl} grains is increased. The favored growth of these latter grains is most likely due to a combination of mechanisms that involve nucleation site preferences and probably the presence of high mobility CSL boundaries. Σ5 boundaries were observed to increase in frequency with Sn through all stages of recrystallization. Additionally {100} grains were found to be most frequently correlated with Σ5 interfaces, which might be due to geometrical considerations. Site-specific characterization of grain boundaries was conducted with three-dimensional atom probe tomography (3D-APT) to measure the grain boundary segregation of Sn.
- 18 June 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 375 (1) , 012016
Open AccessSegregation affecting the evolution of primary recrystallization textures in a ternary Fe-Si-Sn alloy
The effect of Sn addition on the primary recrystallization of cold rolled Fe-3 wt. % Si alloys is investigated. Texture evolution and misorientation distributions are analyzed on partially recrystallized samples using the electron backscatter diffraction technique (EBSD). Sn was found to affect the microstructure, throughout the thermal treatment of the materials, by refining the grains and altering the texture. In the presence of Sn, the intensity of {111}<uvw> grains is reduced through all stages of recrystallization, while that of {100}<uvw> and {hkl} grains is increased. The favored growth of these latter grains is most likely due to a combination of mechanisms that involve nucleation site preferences and probably the presence of high mobility CSL boundaries. Σ5 boundaries were observed to increase in frequency with Sn through all stages of recrystallization. Additionally {100} grains were found to be most frequently correlated with Σ5 interfaces, which might be due to geometrical considerations. Site-specific characterization of grain boundaries was conducted with three-dimensional atom probe tomography (3D-APT) to measure the grain boundary segregation of Sn.
- Open Access
- 16 October 2017
- Published by AIP Publishing in AIP Advances
- Vol. 8 (4)
Influence of initial heating during final high temperature annealing on the offset of primary and secondary recrystallization in Cu-bearing grain oriented electrical steels
The industrial production route of Grain Oriented Electrical Steels (GOES) is complex and fine-tuned for each grade. Its metallurgical process requires in all cases the abnormal grain growth (AGG) of the Goss orientation during the final high temperature annealing (HTA). The exact mechanism of AGG is not yet fully understood, but is controlled by the different inhibition systems, namely MnS, AlN and CuxS, their size and distribution, and the initial primary recrystallized grain size. Therefore, among other parameters, the initial heating stage during the HTA is crucial for the proper development of primary and secondary recrystallized microstructures. Cold rolled 0.3 mm Cu-bearing Grain Oriented Electrical Steel has been submitted to interrupted annealing experiments in a lab tubular furnace. Two different annealing cycles were applied:• Constant heating at 30°C/h up to 1000°C. Two step cycle with initial heating at 100°C/h up to 600°C, followed by 18 h soaking at 600°C and then heating at 30°C/h up to 1050°C. The materials are analyzed in terms of their magnetic properties, grain size, texture and precipitates. The characteristic magnetic properties are analyzed for the different extraction temperatures and Cycles. As the annealing was progressing, the coercivity values (Hc 1.7T [A/m]) decreased, showing two abrupt drops, which can be associated to the on-set of primary and secondary recrystallization. The primary recrystallized grain sizes and recrystallized fractions are fitted to a model using a non-isothermal approach. This analysis shows that, although the resulting grain sizes were similar, the kinetics for the two step annealing were faster due to the lower recovery. The on-set of secondary recrystallization was also shifted to higher temperatures in the case of the continuous heating cycle, which might end in different final grain sizes and final magnetic properties. In both samples, nearly all the observed precipitates are Al-Si-Mn nitrides, ranging from pure AlN to Si4Mn-nitride.
- 16 October 2017
- Published by AIP Publishing in AIP Advances
- Vol. 8 (4)
Open AccessInfluence of initial heating during final high temperature annealing on the offset of primary and secondary recrystallization in Cu-bearing grain oriented electrical steels
The industrial production route of Grain Oriented Electrical Steels (GOES) is complex and fine-tuned for each grade. Its metallurgical process requires in all cases the abnormal grain growth (AGG) of the Goss orientation during the final high temperature annealing (HTA). The exact mechanism of AGG is not yet fully understood, but is controlled by the different inhibition systems, namely MnS, AlN and CuxS, their size and distribution, and the initial primary recrystallized grain size. Therefore, among other parameters, the initial heating stage during the HTA is crucial for the proper development of primary and secondary recrystallized microstructures. Cold rolled 0.3 mm Cu-bearing Grain Oriented Electrical Steel has been submitted to interrupted annealing experiments in a lab tubular furnace. Two different annealing cycles were applied:• Constant heating at 30°C/h up to 1000°C. Two step cycle with initial heating at 100°C/h up to 600°C, followed by 18 h soaking at 600°C and then heating at 30°C/h up to 1050°C. The materials are analyzed in terms of their magnetic properties, grain size, texture and precipitates. The characteristic magnetic properties are analyzed for the different extraction temperatures and Cycles. As the annealing was progressing, the coercivity values (Hc 1.7T [A/m]) decreased, showing two abrupt drops, which can be associated to the on-set of primary and secondary recrystallization. The primary recrystallized grain sizes and recrystallized fractions are fitted to a model using a non-isothermal approach. This analysis shows that, although the resulting grain sizes were similar, the kinetics for the two step annealing were faster due to the lower recovery. The on-set of secondary recrystallization was also shifted to higher temperatures in the case of the continuous heating cycle, which might end in different final grain sizes and final magnetic properties. In both samples, nearly all the observed precipitates are Al-Si-Mn nitrides, ranging from pure AlN to Si4Mn-nitride.
- 15 November 2016
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 879, 430-435
Manganese Effect on Q&P CMnSi Steels
The present study is focused on analyzing the effect of Mn amount in two experimental steel compositions, specially designed for Quenching and Partitiong (Q&P), 0.15C-2.5Mn-1.5Si and 0.15C-3Mn-1.5Si without significant contribution of Al. Two-Step Q&P thermal treatments were performed at laboratory scale in a quenching dilatometer Bähr DIL805A/D. The fractions of retained austenite were evaluated by X-ray diffraction techniques. The mechanical properties of the Q&P samples were evaluated, a strong dependence of strength, uniform elongation and strain hardening values on process parameters has been found. Higher uniform elongation were related to higher residual austenite contents. The 0.15C-3Mn-1.5Si steel showed systematically the largest mechanical values with respect to the 0.15C-2.5Mn-1.5Si steel.
- 15 November 2016
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 879, 430-435
Manganese Effect on Q&P CMnSi Steels
The present study is focused on analyzing the effect of Mn amount in two experimental steel compositions, specially designed for Quenching and Partitiong (Q&P), 0.15C-2.5Mn-1.5Si and 0.15C-3Mn-1.5Si without significant contribution of Al. Two-Step Q&P thermal treatments were performed at laboratory scale in a quenching dilatometer Bähr DIL805A/D. The fractions of retained austenite were evaluated by X-ray diffraction techniques. The mechanical properties of the Q&P samples were evaluated, a strong dependence of strength, uniform elongation and strain hardening values on process parameters has been found. Higher uniform elongation were related to higher residual austenite contents. The 0.15C-3Mn-1.5Si steel showed systematically the largest mechanical values with respect to the 0.15C-2.5Mn-1.5Si steel.
- 1 January 2016
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 656, 378-382
Physical, microstructural and mechanical study of isochronal annealing of deformed commercial iron
- 1 January 2016
- Published by Elsevier in Journal of Alloys and Compounds
- Vol. 656, 378-382
Physical, microstructural and mechanical study of isochronal annealing of deformed commercial iron
- Open Access
- 1 March 2015
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 627, 42-50
Hot working analysis of a CuZn40Pb2 brass on the monophasic (β) and intercritical (α+β) regions
- 1 March 2015
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 627, 42-50
Open AccessHot working analysis of a CuZn40Pb2 brass on the monophasic (β) and intercritical (α+β) regions