Ramanujam Radhakrishnan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ramanujam Radhakrishnan has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
K. Venkatesan
11 shared publications- Chidambaram Kannan
School of Mechanical Engineering, Vellore Institute of Technology, Vellore, Tamil Nadu, India
6 shared publications P. Kuppan
VIT University
6 shared publications- Margabandu Vignesh
Department of Mechanical Engineering, Amrita School of Engineering, Amrita Vishwa Vidyapeetham, Chennai 601102, India
4 shared publications - Arunachalam Senbagam Setra Balan
Department of Mechanical Engineering, National Institute of Technology Karnataka, Mangalore, India
2 shared publications - K. Venkatesan
School of Mechanical Engineering, Vellore Institute of Technology, Vellore, India
2 shared publications
Latest Publications
- Open Access
- 6 November 2025
- Published by IEOM Society International
AI Based AHP and CoCoSo Model for Automotive Piston Material Selection in Additive Manufacturing
The automotive industry continually strives to develop components that are lighter, stronger, and more sustainable. In this context, the need for systematic and intelligent material selection methods has become increasingly significant. This study investigates MCDM based material selection model for piston production within the framework of emerging additive manufacturing technologies. The research is conducted in two stages. In the first stage, various potential metal composites for additive manufacturing of automotive pistons are evaluated and ranked using an Artificial Intelligence (AI)-assisted Analytic Hierarchy Process (AHP). AI techniques are employed to enhance the precision and objectivity of the pairwise comparison process and to ensure consistency in the evaluation of key criteria such as sustainability, cost-effectiveness, and performance. In the second stage, the highest-ranked composite material identified through the AI–AHP framework is further validated using the Combined Compromise Solution (CoCoSo) method and compared with the conventionally used M174 aluminum alloy. The results reveal that the selected composite exhibits superior mechanical, thermal, and environmental performance compared to M174 aluminum. This study underscores the importance of intelligent, data-driven decision-making framework such as AI-integrated AHP and CoCoSo in achieving optimized and sustainable material selection for automotive composites in additive manufacturing.
- 6 November 2025
- Published by IEOM Society International
Open AccessAI Based AHP and CoCoSo Model for Automotive Piston Material Selection in Additive Manufacturing
The automotive industry continually strives to develop components that are lighter, stronger, and more sustainable. In this context, the need for systematic and intelligent material selection methods has become increasingly significant. This study investigates MCDM based material selection model for piston production within the framework of emerging additive manufacturing technologies. The research is conducted in two stages. In the first stage, various potential metal composites for additive manufacturing of automotive pistons are evaluated and ranked using an Artificial Intelligence (AI)-assisted Analytic Hierarchy Process (AHP). AI techniques are employed to enhance the precision and objectivity of the pairwise comparison process and to ensure consistency in the evaluation of key criteria such as sustainability, cost-effectiveness, and performance. In the second stage, the highest-ranked composite material identified through the AI–AHP framework is further validated using the Combined Compromise Solution (CoCoSo) method and compared with the conventionally used M174 aluminum alloy. The results reveal that the selected composite exhibits superior mechanical, thermal, and environmental performance compared to M174 aluminum. This study underscores the importance of intelligent, data-driven decision-making framework such as AI-integrated AHP and CoCoSo in achieving optimized and sustainable material selection for automotive composites in additive manufacturing.
- 22 August 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (12) , 10946-10963
Investigation of Corrosion Behavior of Wrought and Wire + Arc Additive Manufactured Inconel 625 in Air and Molten Salts at High-Temperature Environments
- 22 August 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (12) , 10946-10963
Investigation of Corrosion Behavior of Wrought and Wire + Arc Additive Manufactured Inconel 625 in Air and Molten Salts at High-Temperature Environments
- 10 January 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (2) , 1026-1049
Investigation of Surface Residual Stress, Mechanical Properties, and Metallurgical Characterization of Inconel 625 Multilayer Thin-Wall Component Using Cold Metal Transfer Technique
- 10 January 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (2) , 1026-1049
Investigation of Surface Residual Stress, Mechanical Properties, and Metallurgical Characterization of Inconel 625 Multilayer Thin-Wall Component Using Cold Metal Transfer Technique
- 4 March 2022
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 26 (2) , 160-182
Machining of Y 2 O 3 reinforced magnesium rare earth alloys using wire electrical discharge turning process
Advanced machining has become one of the inevitable processes for the fabrication of miniature industrial components that demands high dimensional accuracy. Magnesium (Mg) and its composites have widespread applications in the areas of aerospace, medical, and automobile sectors. The objective of this work is to analyze the machinability of Mg—rare earth (RE) alloy (Mg3Al2.5La)-based nanocomposites using wire electrical discharge turning (WEDT), a variant of EDM process. Y2O3 (0.6 and 1.9%) reinforced magnesium composites are prepared through disintegrated melt deposition technique. SEM and XRD analyses confirmed the intermetallic phase formation, such as Al11La3, and Al2La. Machining experiments are conducted with input parameters: discharge ON time, wire feed and spindle rotational speed each varied at three levels to study surface roughness (Ra) and volume of material removed (MRR). Results showed that Ra of the machined samples increases and MRR decreases, with the increase in % reinforcement and discharge ON time. The lower Ra value of 2.985 µm and higher MRR of 34.85 mm3/min are observed for the Mg3Al2.5La sample. This result is attributed to the absence of particle pullout and increased thermal conductivity of magnesium alloy during machining. Prediction analysis based on mean values is carried out to confirm the accuracy of the experimental results at optimal parametric levels.
- 4 March 2022
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 26 (2) , 160-182
Machining of Y 2 O 3 reinforced magnesium rare earth alloys using wire electrical discharge turning process
Advanced machining has become one of the inevitable processes for the fabrication of miniature industrial components that demands high dimensional accuracy. Magnesium (Mg) and its composites have widespread applications in the areas of aerospace, medical, and automobile sectors. The objective of this work is to analyze the machinability of Mg—rare earth (RE) alloy (Mg3Al2.5La)-based nanocomposites using wire electrical discharge turning (WEDT), a variant of EDM process. Y2O3 (0.6 and 1.9%) reinforced magnesium composites are prepared through disintegrated melt deposition technique. SEM and XRD analyses confirmed the intermetallic phase formation, such as Al11La3, and Al2La. Machining experiments are conducted with input parameters: discharge ON time, wire feed and spindle rotational speed each varied at three levels to study surface roughness (Ra) and volume of material removed (MRR). Results showed that Ra of the machined samples increases and MRR decreases, with the increase in % reinforcement and discharge ON time. The lower Ra value of 2.985 µm and higher MRR of 34.85 mm3/min are observed for the Mg3Al2.5La sample. This result is attributed to the absence of particle pullout and increased thermal conductivity of magnesium alloy during machining. Prediction analysis based on mean values is carried out to confirm the accuracy of the experimental results at optimal parametric levels.
- 10 April 2021
- Published by Springer Nature in Sādhanā
- Vol. 46 (2) , 1-9
Statistical modelling and analysis of material removal rate and surface roughness during wire electrical discharge hybrid turning (WEDHT) process
- 10 April 2021
- Published by Springer Nature in Sādhanā
- Vol. 46 (2) , 1-9
Statistical modelling and analysis of material removal rate and surface roughness during wire electrical discharge hybrid turning (WEDHT) process
- 14 October 2020
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 235 (8) , 1561-1574
Mathematical modeling and optimization of tribological behaviour of Al 7075 based hybrid nanocomposites
Many industrial applications necessitate lightweight materials that possess better tribological behaviour. Whilst aluminium based nanocomposites are proposed owing to their lightness, their tribological characteristics must be improved which are dominantly influenced by the selection of reinforcements, manufacturing process and heat treatments. In this research, an aluminium hybrid nanocomposite is produced using a novel molten salt processing and subjected to different heat treatments. Their tribological behaviour is assessed under different operating conditions viz. load, sliding velocity and material condition of the pin. Regression models are formulated to predict the tribological behaviour of developed hybrid composite under different heat treatments. The most significant parameter and optimum level for each of these operating parameters are determined using analysis of variance, main and interaction plots and response surface methodology in the end. The integrated approach helps in deciding the optimum parameter setting for the development of nanocomposite with ameliorated tribological behaviour. Under the optimized conditions, the hybrid nanocomposite could able to reduce the wear resistance by about 63% and the coefficient of friction by 18.5% than unreinforced alloy.
- 14 October 2020
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology
- Vol. 235 (8) , 1561-1574
Mathematical modeling and optimization of tribological behaviour of Al 7075 based hybrid nanocomposites
Many industrial applications necessitate lightweight materials that possess better tribological behaviour. Whilst aluminium based nanocomposites are proposed owing to their lightness, their tribological characteristics must be improved which are dominantly influenced by the selection of reinforcements, manufacturing process and heat treatments. In this research, an aluminium hybrid nanocomposite is produced using a novel molten salt processing and subjected to different heat treatments. Their tribological behaviour is assessed under different operating conditions viz. load, sliding velocity and material condition of the pin. Regression models are formulated to predict the tribological behaviour of developed hybrid composite under different heat treatments. The most significant parameter and optimum level for each of these operating parameters are determined using analysis of variance, main and interaction plots and response surface methodology in the end. The integrated approach helps in deciding the optimum parameter setting for the development of nanocomposite with ameliorated tribological behaviour. Under the optimized conditions, the hybrid nanocomposite could able to reduce the wear resistance by about 63% and the coefficient of friction by 18.5% than unreinforced alloy.
- 11 July 2020
- Published by Springer Nature
- p. 653-662
Application of Grey Theory and Fuzzy Logic to Optimize Machining Parameters of Zircon Sand Reinforced Aluminum Composites
- 11 July 2020
- Published by Springer Nature
- p. 653-662
Application of Grey Theory and Fuzzy Logic to Optimize Machining Parameters of Zircon Sand Reinforced Aluminum Composites
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 22, 1507-1516
Machinability studies on aluminium matrix nanocomposite under the influence of MQL
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 22, 1507-1516
Machinability studies on aluminium matrix nanocomposite under the influence of MQL
- 13 August 2019
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 41 (9)
Machining of Ti–6Al–4V using diffusion annealed zinc-coated brass wire in WEDHT
- 13 August 2019
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 41 (9)
Machining of Ti–6Al–4V using diffusion annealed zinc-coated brass wire in WEDHT