Xinbao Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xinbao Liu has a total of 64 co-authors. Here are the top co-authors by number of shared publications:
Susumu Takamori
10 shared publicationsYoshiaki Osawa
10 shared publicationsPing Fan
School of Information Science and Technology, Northwest University, Xi’an, China
6 shared publications- Fuxing Yin
Hebei university of Technology
4 shared publications Lin Zhu
School of Chemical Engineering, Northwest University, Xi’an, China
4 shared publicationsMitsuharu Shiwa
4 shared publications
Latest Publications
- 13 January 2022
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 39 (2) , 122-132
High-temperature creep life prediction of 9%Cr steel based on creep cavitation modelling
In present work, the creep rupture life of 9% Cr heat-resistant steel (P91) was evaluated based on the creep cavitation modelling. At 873 K, a series of creep rupture tests were carried out under the stresses of 140–190 MPa to achieve several sets of ruptured specimens . The constrained and unconstrained models of cavity growth were introduced to investigate the creep behaviour of P91 steel. The obtained results showed that the rupture mechanism of these specimens was mainly attributed to the ductile rupture under the present creep conditions. Besides, reasonable extrapolations were calculated to predict the creep rupture life of P91 steel by combining different constitutive equations with the cavity growth model. It suggested that the model predictions with constraints were better than those with unconstrained conditions. In particular, the Sinh equation based constrained cavity model shows greater potential in predicting the long-term creep life of P91 steel.
- 13 January 2022
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 39 (2) , 122-132
High-temperature creep life prediction of 9%Cr steel based on creep cavitation modelling
In present work, the creep rupture life of 9% Cr heat-resistant steel (P91) was evaluated based on the creep cavitation modelling. At 873 K, a series of creep rupture tests were carried out under the stresses of 140–190 MPa to achieve several sets of ruptured specimens . The constrained and unconstrained models of cavity growth were introduced to investigate the creep behaviour of P91 steel. The obtained results showed that the rupture mechanism of these specimens was mainly attributed to the ductile rupture under the present creep conditions. Besides, reasonable extrapolations were calculated to predict the creep rupture life of P91 steel by combining different constitutive equations with the cavity growth model. It suggested that the model predictions with constraints were better than those with unconstrained conditions. In particular, the Sinh equation based constrained cavity model shows greater potential in predicting the long-term creep life of P91 steel.
- 22 November 2021
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 22 (1) , 259-266
Failure Analysis of the Leakage and Ignition of an Oil–Gas Mixture Transportation Pipeline
- 22 November 2021
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- Vol. 22 (1) , 259-266
Failure Analysis of the Leakage and Ignition of an Oil–Gas Mixture Transportation Pipeline
- 1 June 2021
- Published by Elsevier in Engineering Failure Analysis
- Vol. 124
Fracture analysis of a pulley shaft for the linear motor oil pumping unit in western oilfield of China
- 1 June 2021
- Published by Elsevier in Engineering Failure Analysis
- Vol. 124
Fracture analysis of a pulley shaft for the linear motor oil pumping unit in western oilfield of China
- 9 March 2021
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 38 (3) , 158-165
Characterisation of microstructure evolution during creep of P91 steel using the electron backscatter diffraction technique
The present work deals with the microstructure evolution during creep of P91 steel. In particular, the changes of prior austenite grain (PAG) and low-angle grain boundary (LAGB) during creep were studied using the electron backscatter diffraction (EBSD). Firstly, a series of crept specimens of P91 steel were prepared at 893 K under a constant stress of 145 MPa. Then, the EBSD measurements of these specimens were carried out. Subsequently, the PAGs were reconstructed successfully with the measured EBSD data, and the resultant distribution of LAGBs was calculated. Consequently, the obtained results suggested that the size of PAGs has not changed significantly during the whole creep. For the distribution of LAGBs, however, the peak shifted obviously to high angles during creep. In addition, it demonstrated that the EBSD method offers an effective and quantitative tool to characterise the microstructure evolution during creep of P91 steel.
- 9 March 2021
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 38 (3) , 158-165
Characterisation of microstructure evolution during creep of P91 steel using the electron backscatter diffraction technique
The present work deals with the microstructure evolution during creep of P91 steel. In particular, the changes of prior austenite grain (PAG) and low-angle grain boundary (LAGB) during creep were studied using the electron backscatter diffraction (EBSD). Firstly, a series of crept specimens of P91 steel were prepared at 893 K under a constant stress of 145 MPa. Then, the EBSD measurements of these specimens were carried out. Subsequently, the PAGs were reconstructed successfully with the measured EBSD data, and the resultant distribution of LAGBs was calculated. Consequently, the obtained results suggested that the size of PAGs has not changed significantly during the whole creep. For the distribution of LAGBs, however, the peak shifted obviously to high angles during creep. In addition, it demonstrated that the EBSD method offers an effective and quantitative tool to characterise the microstructure evolution during creep of P91 steel.
- Open Access
- 1 March 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 706 (1) , 012037
Failure Analysis on Fiber Reinforced Thermoplastic Pipe
In recent years, fiber reinforced thermoplastic pipe (FRTP) has been widely used in oil fields of China due to its excellent corrosion resistance and coiling performance. With the further expansion of application scope, some failure accidents have occurred. Based on the inspection of the wall thickness, chemical composition and physical properties of a failed FRTP in the western oilfield of China, the causes are systematically analyzed. The results show that the main cause of the sample fracture is the decrease of the strength of FRTP due to the oil and gas media constantly penetrate into the lining and reinforced layer during the long-term service. Moreover, it is found that the outer sheath is worn and penetrated to the reinforced layer which further reduces the bearing pressure performance of FRTP and finally causes the fracture failure.
- 1 March 2021
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 706 (1) , 012037
Open AccessFailure Analysis on Fiber Reinforced Thermoplastic Pipe
In recent years, fiber reinforced thermoplastic pipe (FRTP) has been widely used in oil fields of China due to its excellent corrosion resistance and coiling performance. With the further expansion of application scope, some failure accidents have occurred. Based on the inspection of the wall thickness, chemical composition and physical properties of a failed FRTP in the western oilfield of China, the causes are systematically analyzed. The results show that the main cause of the sample fracture is the decrease of the strength of FRTP due to the oil and gas media constantly penetrate into the lining and reinforced layer during the long-term service. Moreover, it is found that the outer sheath is worn and penetrated to the reinforced layer which further reduces the bearing pressure performance of FRTP and finally causes the fracture failure.
- 1 January 2020
- Published by Elsevier in International Journal of Pressure Vessels and Piping
- Vol. 179
Prediction of long-term creep life of 9Cr–1Mo–V–Nb steel using artificial neural network
- 1 January 2020
- Published by Elsevier in International Journal of Pressure Vessels and Piping
- Vol. 179
Prediction of long-term creep life of 9Cr–1Mo–V–Nb steel using artificial neural network
- 20 September 2019
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 141 (6)
Comparative Study of Creep Behavior in 9Cr-1Mo Steel With Different Prediction Methods
Over the range of variables (temperature and stress) normally encountered in service applications, creep behaviors of 9Cr-1Mo steel were investigated with various models, such as Wilshire model, combination of exponential form and omega (CEO) model, and continuum damage mechanics (CDM) model. First, a series of short-term creep data was prepared to evaluate the material parameters occurring in these models. Then, creep curve, minimum creep rate, and long-term creep life of present 9Cr-1Mo steel were extrapolated with these estimated models. Based on the analysis of obtained results in detail, it suggested that both CDM model and CEO model can give reliable minimum creep rate predictions. However, the most reliable values of long-term creep life are obtained by the CDM model, followed by the Wilshire model and then the CEO model. In particular, the physically based CDM model can provide useful insights into the underlying creep mechanisms. Therefore, the CDM model has promising potential to study the long-term creep behaviors of 9Cr-1Mo steels.
- 20 September 2019
- Published by ASME International in Journal of Pressure Vessel Technology
- Vol. 141 (6)
Comparative Study of Creep Behavior in 9Cr-1Mo Steel With Different Prediction Methods
Over the range of variables (temperature and stress) normally encountered in service applications, creep behaviors of 9Cr-1Mo steel were investigated with various models, such as Wilshire model, combination of exponential form and omega (CEO) model, and continuum damage mechanics (CDM) model. First, a series of short-term creep data was prepared to evaluate the material parameters occurring in these models. Then, creep curve, minimum creep rate, and long-term creep life of present 9Cr-1Mo steel were extrapolated with these estimated models. Based on the analysis of obtained results in detail, it suggested that both CDM model and CEO model can give reliable minimum creep rate predictions. However, the most reliable values of long-term creep life are obtained by the CDM model, followed by the Wilshire model and then the CEO model. In particular, the physically based CDM model can provide useful insights into the underlying creep mechanisms. Therefore, the CDM model has promising potential to study the long-term creep behaviors of 9Cr-1Mo steels.
- 6 September 2019
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 36 (6) , 548-561
Creep rupture behaviour of modified 9Cr-1Mo heat-resistant steel strengthened with different mechanisms
The creep rupture behaviours and microstructural changes of a modified 9Cr-1Mo heat-resistant steel were investigated at 853 K. Analysis of creep results suggests that dislocation climb is the dominant deformation mechanism with true stress exponent of 5 under the present conditions. Based on the microstructural analysis, strengthening contributions from M23C6 carbides and MX carbonitrides were clarified. The M23C6 carbides can promote grain boundary strengthening by exerting Zener pinning forces, whereas MX carbonitrides can enhance the creep strength by interacting with mobile dislocations to induce threshold stress. Besides, softening of the steel is related not only to the decrease of dislocations, but also the coarsening of precipitates and substructures. The value of creep damage tolerance factor is close to 6.6, which further confirms that the creep damage is mainly attributed to the microstructural degradations, such as the coarsening of precipitates and substructures and decrease of dislocations.
- 6 September 2019
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 36 (6) , 548-561
Creep rupture behaviour of modified 9Cr-1Mo heat-resistant steel strengthened with different mechanisms
The creep rupture behaviours and microstructural changes of a modified 9Cr-1Mo heat-resistant steel were investigated at 853 K. Analysis of creep results suggests that dislocation climb is the dominant deformation mechanism with true stress exponent of 5 under the present conditions. Based on the microstructural analysis, strengthening contributions from M23C6 carbides and MX carbonitrides were clarified. The M23C6 carbides can promote grain boundary strengthening by exerting Zener pinning forces, whereas MX carbonitrides can enhance the creep strength by interacting with mobile dislocations to induce threshold stress. Besides, softening of the steel is related not only to the decrease of dislocations, but also the coarsening of precipitates and substructures. The value of creep damage tolerance factor is close to 6.6, which further confirms that the creep damage is mainly attributed to the microstructural degradations, such as the coarsening of precipitates and substructures and decrease of dislocations.
- 1 April 2019
- Published by Elsevier in Materials Characterization
- Vol. 150, 98-106
Characterization of dislocation evolution during creep of 9Cr 1Mo steel using internal friction measurement
- 1 April 2019
- Published by Elsevier in Materials Characterization
- Vol. 150, 98-106
Characterization of dislocation evolution during creep of 9Cr 1Mo steel using internal friction measurement
- 20 March 2019
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 28 (4) , 2348-2355
A Study of Microstructure Evolution During Creep of 9Cr-1Mo Steel Using Ultrasonic and Hardness Measurements
- 20 March 2019
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 28 (4) , 2348-2355
A Study of Microstructure Evolution During Creep of 9Cr-1Mo Steel Using Ultrasonic and Hardness Measurements