Ednan Joanni
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ednan Joanni has a total of 151 co-authors. Here are the top co-authors by number of shared publications:
- Raluca Savu
INESC Porto
25 shared publications - Paulo Roberto Bueno
São Paulo State University (UNESP)
13 shared publications - Rajesh Kumar
Institute of Materials Science Technical University of Darmstadt Darmstadt Germany
11 shared publications - Sumanta Sahoo
Department of Chemistry Gachon University Seongnam‐si Gyeonggi‐do Republic of Korea
9 shared publications - Elson Longo
Federal University of Sao Carlos (UFSCar)
8 shared publications - Miguel Adolfo Ponce
Institute of Materials Science and Technology (INTEMA), University of Mar del Plata and National Research Council (CONICET), Mar del Plata, Argentina
6 shared publications
Latest Publications
- 10 November 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (67) , 45900-45926
Laser and microwave-assisted synthesis and modification of graphene-based materials for supercapacitor and battery electrodes
Laser and microwave approaches for processing graphene materials for advanced energy storage devices.
- 10 November 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (67) , 45900-45926
Laser and microwave-assisted synthesis and modification of graphene-based materials for supercapacitor and battery electrodes
Laser and microwave approaches for processing graphene materials for advanced energy storage devices.
- Top Cited PapersOpen Access
Dual-doped graphene-based electrode materials for energy devices
- 1 April 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 43 (3)
Ultrathin tantalum films for Schottky contacts on 4H silicon carbide
Since ultrathin films of 2 nm thickness with Ni and W revealed interesting aspects in Schottky barrier diodes in previous works, exhibiting effective quality of the interface and thermal stability under electrical characterizations. This work presents data obtained using Ta as Schottky contact, even though it is often used as Ohmic contact, but due to its refractory properties and low work function, the result could be favorable to low voltage drop devices in power electronics. Under the development of the work, a range of annealing processing was conducted to verify the phenomena involved combining tantalum ultrathin films. After electrical tests under I–V curves, a range of Schottky barrier heights (SBHs) was noticed without Fermi level pinning, following a highlighted device that demonstrated results of ideality of around 1, SBH of 0.8 eV, alto showing high rectification ratio and low reverse leakage current, around 10−6 A at −200 V. To finish the work, XPS and SEM characterization were carried out to provide interface structure details and reveal tantalum oxides and carbides, where they probably contribute to the Schottky behavior, and the values achieved.
- 1 April 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology B
- Vol. 43 (3)
Ultrathin tantalum films for Schottky contacts on 4H silicon carbide
Since ultrathin films of 2 nm thickness with Ni and W revealed interesting aspects in Schottky barrier diodes in previous works, exhibiting effective quality of the interface and thermal stability under electrical characterizations. This work presents data obtained using Ta as Schottky contact, even though it is often used as Ohmic contact, but due to its refractory properties and low work function, the result could be favorable to low voltage drop devices in power electronics. Under the development of the work, a range of annealing processing was conducted to verify the phenomena involved combining tantalum ultrathin films. After electrical tests under I–V curves, a range of Schottky barrier heights (SBHs) was noticed without Fermi level pinning, following a highlighted device that demonstrated results of ideality of around 1, SBH of 0.8 eV, alto showing high rectification ratio and low reverse leakage current, around 10−6 A at −200 V. To finish the work, XPS and SEM characterization were carried out to provide interface structure details and reveal tantalum oxides and carbides, where they probably contribute to the Schottky behavior, and the values achieved.
- 28 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Development of resistors with TaxNy deposited by RF sputtering using lithography technique
In this work, a Ta x N y thin film was used to manufacture resistors. The film was deposited by RF sputtering on an 96% polished alumina substrate, and it has a thickness, sheet resistance and resistivity of 150 nm, 181.63 Ω/sq and 2.72 mΩcm, respectively. Here, two types of resistor configurations were developed. The first one, is a set of resistors composed of five resistors with fixed length (L) and varying width (W) values. The second one is a set with TLM (Transfer Length Method) type configuration, which consists of six resistors in series with a fixed width (W) value and varying length (L) values. Both resistor configurations, shown a dependence almost linear with the resistance and a reproductive behavior, which allows uniformity in the manufacturing process. This study show that it is possible to use Ta x N y films to manufacture resistors that permit you to tune the resistance values according to the needs of your application, for example in Multi-chip module (MCM).
- 28 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Development of resistors with TaxNy deposited by RF sputtering using lithography technique
In this work, a Ta x N y thin film was used to manufacture resistors. The film was deposited by RF sputtering on an 96% polished alumina substrate, and it has a thickness, sheet resistance and resistivity of 150 nm, 181.63 Ω/sq and 2.72 mΩcm, respectively. Here, two types of resistor configurations were developed. The first one, is a set of resistors composed of five resistors with fixed length (L) and varying width (W) values. The second one is a set with TLM (Transfer Length Method) type configuration, which consists of six resistors in series with a fixed width (W) value and varying length (L) values. Both resistor configurations, shown a dependence almost linear with the resistance and a reproductive behavior, which allows uniformity in the manufacturing process. This study show that it is possible to use Ta x N y films to manufacture resistors that permit you to tune the resistance values according to the needs of your application, for example in Multi-chip module (MCM).
- Top Cited Papers
Composites based on layered materials for absorption of microwaves and electromagnetic shielding
- 20 April 2023
- Published by Royal Society of Chemistry (RSC) in Chemical Communications
- Vol. 59 (41) , 6109-6127
Vacancy designed 2D materials for electrodes in energy storage devices
Vacancies are ubiquitous in nature, usually playing an important role in determining how a material behaves, both physically and chemically.
- 20 April 2023
- Published by Royal Society of Chemistry (RSC) in Chemical Communications
- Vol. 59 (41) , 6109-6127
Vacancy designed 2D materials for electrodes in energy storage devices
Vacancies are ubiquitous in nature, usually playing an important role in determining how a material behaves, both physically and chemically.