Enrico Verlato
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Enrico Verlato has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Lourdes Vázquez-Gómez
National Research Council – Institute of Condensed Matter Chemistry and Technologies for Energy, Padova, Italy, Italy
22 shared publications Nicola Comisso
21 shared publicationsMarco Musiani
CNR-ICMATE, 35127 Padova, Italy
18 shared publications- Sandro Cattarin
CNR-IENI (Italy)
18 shared publications - Paolo Guerriero
ICIS-CNR
16 shared publications Luca Mattarozzi
15 shared publications
Latest Publications
- Open Access
- 12 October 2026
- Published by Wiley in ChemElectroChem
- Vol. 13 (20)
Comparison of Different Electrochemical Setups for Noninvasive Impedance Measurements on Archeological Coins
The electrochemical characterization of cultural heritage objects requires noninvasive approaches. In the case of patina‐covered bronze objects, two essential features of the setups recently proposed to satisfy this requirement are (i) the use of gel electrolytes and (ii) the absence of metal contacts that might damage the patina (or, at least, the control of the size of the damaged area to make it invisible to the naked eye). In the present work we show how the impedance of model coins is most conveniently measured using a four‐electrode setup where the sample is mounted in a symmetrical two‐compartment cell filled with a gel electrolyte which contacts both coin faces. Results are presented for model coins with polished surfaces, patina‐covered coins, coins pretreated with a corrosion inhibitor (benzotriazole), and coins coated with a commercial acrylate/methacrylate copolymer (Paraloid B‐72 (R) ). Compared with alternative approaches involving two‐electrode or three‐electrode setups, our approach is the only one which simultaneously warrants a noninvasive character and the direct determination of the sample impedance without needing any correction. Although only model coins were used in this study, the above conclusion applies as well to true archaeological coins.
- 12 October 2026
- Published by Wiley in ChemElectroChem
- Vol. 13 (20)
Open AccessComparison of Different Electrochemical Setups for Noninvasive Impedance Measurements on Archeological Coins
The electrochemical characterization of cultural heritage objects requires noninvasive approaches. In the case of patina‐covered bronze objects, two essential features of the setups recently proposed to satisfy this requirement are (i) the use of gel electrolytes and (ii) the absence of metal contacts that might damage the patina (or, at least, the control of the size of the damaged area to make it invisible to the naked eye). In the present work we show how the impedance of model coins is most conveniently measured using a four‐electrode setup where the sample is mounted in a symmetrical two‐compartment cell filled with a gel electrolyte which contacts both coin faces. Results are presented for model coins with polished surfaces, patina‐covered coins, coins pretreated with a corrosion inhibitor (benzotriazole), and coins coated with a commercial acrylate/methacrylate copolymer (Paraloid B‐72 (R) ). Compared with alternative approaches involving two‐electrode or three‐electrode setups, our approach is the only one which simultaneously warrants a noninvasive character and the direct determination of the sample impedance without needing any correction. Although only model coins were used in this study, the above conclusion applies as well to true archaeological coins.
- Open Access
- 27 February 2025
- Published by Royal Society of Chemistry (RSC) in Nanoscale
Swapping CO2 electro-reduction active sites on a nickel-based hybrid formed on a “guilty” covalent triazine framework
Ultra-small Ni NPs on a “non-innocent” N-enriched C-carrier promote unconventional CO2-to-formate electroreduction at low potential values. Developed using Pov-RAY software and Corel Photo Paint.
- 27 February 2025
- Published by Royal Society of Chemistry (RSC) in Nanoscale
Open AccessSwapping CO2 electro-reduction active sites on a nickel-based hybrid formed on a “guilty” covalent triazine framework
Ultra-small Ni NPs on a “non-innocent” N-enriched C-carrier promote unconventional CO2-to-formate electroreduction at low potential values. Developed using Pov-RAY software and Corel Photo Paint.
- 25 April 2024
- Published by Elsevier in Electrochimica Acta
- Vol. 489, 144317
ISE pages
- Open Access
- 17 February 2023
- Published by Wiley in ChemElectroChem
- Vol. 10 (6)
Electrodeposition of Ni−Rh Alloys and their Use as Cathodes for Nitrate Reduction in Alkaline Solutions
Compact Ni−Rh alloys are electrodeposited potentiostatically on rotating disk and sheet electrodes; film compositions are adjusted by varying bath composition and deposition potential Edep. SEM images of these alloys show a compact, globular morphology for Rh contents up to 30 at%, and a smoother aspect for films with a medium‐to‐high content of Rh. XRD spectra show the formation of a single crystalline phase, with diffraction peaks in intermediate positions between those of the constituent elements. Data analysis indicates that crystal lattice parameters vary with composition according to Vegard's law. Linear voltammetries of nitrate reduction in alkali highlight a maximum of activity, in terms of reduction current, for alloys in the range of 10–30 at.% Rh. Prolonged electrolysis at appropriate potential performed with Ni85Rh15 alloy shows, in comparison with pure Ni and pure Rh: much increased activity and faster abatement of nitrate; lower production of the undesired nitrite species; higher selectivity towards production of ammonia.
- 17 February 2023
- Published by Wiley in ChemElectroChem
- Vol. 10 (6)
Open AccessElectrodeposition of Ni−Rh Alloys and their Use as Cathodes for Nitrate Reduction in Alkaline Solutions
Compact Ni−Rh alloys are electrodeposited potentiostatically on rotating disk and sheet electrodes; film compositions are adjusted by varying bath composition and deposition potential Edep. SEM images of these alloys show a compact, globular morphology for Rh contents up to 30 at%, and a smoother aspect for films with a medium‐to‐high content of Rh. XRD spectra show the formation of a single crystalline phase, with diffraction peaks in intermediate positions between those of the constituent elements. Data analysis indicates that crystal lattice parameters vary with composition according to Vegard's law. Linear voltammetries of nitrate reduction in alkali highlight a maximum of activity, in terms of reduction current, for alloys in the range of 10–30 at.% Rh. Prolonged electrolysis at appropriate potential performed with Ni85Rh15 alloy shows, in comparison with pure Ni and pure Rh: much increased activity and faster abatement of nitrate; lower production of the undesired nitrite species; higher selectivity towards production of ammonia.
- 12 July 2019
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 7 (30) , 17896-17905
CO2 reduction to formic acid at low overpotential on BDD electrodes modified with nanostructured CeO2
Nanostructured CeO2/BDD electrodes produce formic acid with good faradaic efficiency at very low overpotential (>40% at η ≈ 40 mV).
- 12 July 2019
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 7 (30) , 17896-17905
CO2 reduction to formic acid at low overpotential on BDD electrodes modified with nanostructured CeO2
Nanostructured CeO2/BDD electrodes produce formic acid with good faradaic efficiency at very low overpotential (>40% at η ≈ 40 mV).
- 1 October 2018
- Published by Elsevier in Journal of Industrial and Engineering Chemistry
- Vol. 66, 404-410
Highly stable core–shell Pt-CeO2 nanoparticles electrochemically deposited onto Fecralloy foam reactors for the catalytic oxidation of CO
- 1 October 2018
- Published by Elsevier in Journal of Industrial and Engineering Chemistry
- Vol. 66, 404-410
Highly stable core–shell Pt-CeO2 nanoparticles electrochemically deposited onto Fecralloy foam reactors for the catalytic oxidation of CO
- 25 November 2017
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 93 (6) , 1572-1578
Reductive dehalogenation of a chloroacetanilide herbicide in a flow electrochemical cell fitted with Ag‐modified Ni foams
BACKGROUND: The aim of this work is to adapt the electrochemical reduction of Alachlor™, using Ag‐modified Ni foam electrodes to environmental applications. In this context, preparative electrolyses of Alachlor™ were performed in a flow electrochemical cell in different electrolytic media.RESULTS: The highest catalytic activity for the reduction of Alachlor™ was obtained in 0.05 mol L‐1 NaOH, with a conversion yield of 93%. The dechlorination yield of Alachlor™ estimated from the Cl‐ concentration was 77%, significantly lower than its conversion yield, but higher than the yield of deschloroalachlor (69%), the main dehalogenated by‐product, indicating the presence of other by‐products.CONCLUSIONS: Total reduction of Alachlor™ was achieved in conditions adapted to environmental applications, showing that this process can be used for dechlorination treatment of Alachlor™ in aqueous media. Although a high dechlorination yield was obtained, biodegradability estimated from BOD5 measurements remained low, showing that the C–Cl bond is not the only functional group that is responsible for the biorecalcitrance of Alachlor™. © 2017 Society of Chemical Industry
- 25 November 2017
- Published by Wiley in Journal of Chemical Technology & Biotechnology
- Vol. 93 (6) , 1572-1578
Reductive dehalogenation of a chloroacetanilide herbicide in a flow electrochemical cell fitted with Ag‐modified Ni foams
BACKGROUND: The aim of this work is to adapt the electrochemical reduction of Alachlor™, using Ag‐modified Ni foam electrodes to environmental applications. In this context, preparative electrolyses of Alachlor™ were performed in a flow electrochemical cell in different electrolytic media.RESULTS: The highest catalytic activity for the reduction of Alachlor™ was obtained in 0.05 mol L‐1 NaOH, with a conversion yield of 93%. The dechlorination yield of Alachlor™ estimated from the Cl‐ concentration was 77%, significantly lower than its conversion yield, but higher than the yield of deschloroalachlor (69%), the main dehalogenated by‐product, indicating the presence of other by‐products.CONCLUSIONS: Total reduction of Alachlor™ was achieved in conditions adapted to environmental applications, showing that this process can be used for dechlorination treatment of Alachlor™ in aqueous media. Although a high dechlorination yield was obtained, biodegradability estimated from BOD5 measurements remained low, showing that the C–Cl bond is not the only functional group that is responsible for the biorecalcitrance of Alachlor™. © 2017 Society of Chemical Industry
- 1 November 2017
- Published by Elsevier in Electrochimica Acta
- Vol. 253, 11-20
Preparation of porous oxide layers by oxygen bubble templated anodic deposition followed by galvanic displacement
- 1 November 2017
- Published by Elsevier in Electrochimica Acta
- Vol. 253, 11-20
Preparation of porous oxide layers by oxygen bubble templated anodic deposition followed by galvanic displacement
- 1 June 2017
- Published by Elsevier in Chemical Engineering Journal
- Vol. 317, 551-560
Electrochemical preparation of nanostructured CeO2-Pt catalysts on Fe-Cr-Al alloy foams for the low-temperature combustion of methanol
- 1 June 2017
- Published by Elsevier in Chemical Engineering Journal
- Vol. 317, 551-560
Electrochemical preparation of nanostructured CeO2-Pt catalysts on Fe-Cr-Al alloy foams for the low-temperature combustion of methanol