Song Yi Park
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Song Yi Park has a total of 107 co-authors. Here are the top co-authors by number of shared publications:
- Jin Young Kim
School of Energy and Chemical Engineering, Ulsan National Institute of Science and Technology (UNIST), Ulsan 44919, Republic of Korea
20 shared publications - Han Young Woo
Department of Chemistry, Korea University, Seoul, Republic of Korea
6 shared publications Seo-Jin Ko
6 shared publications- Tack Ho Lee
Graduate Department of Chemical Materials, Institute for Plastic Information and Energy Materials, Sustainable Utilization of Photovoltaic Energy Research Center, Pusan National University, Busan 46241, Republic of Korea
6 shared publications Taehyo Kim
Department of Energy Engineering Ulsan National Institute of Science and Technology (UNIST) Ulsan 44919 Republic of Korea
6 shared publications- Mohammad Afsar Uddin
Instituto de Ciencia de Materiales de Madrid, CSIC, Cantoblanco, 28049 Madrid, Spain
5 shared publications
Latest Publications
- Open Access
- 8 September 2026
- Published by Wiley in Advanced Energy Materials
- p. e71553
Free Charge Generation in Organic Photoconversion Devices–the Impact of Electrostatic Potentials
The generation of free charges in organic semiconductors is fundamentally limited by the formation of tightly bound electron‐hole pairs (excitons) arising from their low dielectric screening. Conventional donor/acceptor (D/A) heterojunctions overcome this limitation through interfacial energetic offsets at the cost of high voltage losses that limit organic photoconversion device efficiency compared to inorganic counterparts. The success of non‐fullerene acceptors (NFAs), enabling efficient charge generation at relatively small energetic offsets, challenges this picture and suggests the need to consider additional charge generation mechanisms. In this review, we highlight the critical role of molecular electrostatic potentials in free charge generation within organic semiconductors. The molecular origins of electrostatic potentials are discussed within the multipole expansion framework, with particular emphasis on quadrupole moments arising from anisotropic charge distributions within a molecule. The role of these electrostatic effects in modulating interfacial energetics, inducing band bending, and facilitating charge separation in donor/acceptor heterojunctions is examined, alongside their extension to single‐component systems. In single‐component systems, orientation‐dependent molecular packing creates functional energetic offsets without the need for distinct donor and acceptor materials. Based on these observations, key molecular and device design strategies for harnessing electrostatic effects in next‐generation organic photoconversion devices are outlined.
- 8 September 2026
- Published by Wiley in Advanced Energy Materials
- p. e71553
Open AccessFree Charge Generation in Organic Photoconversion Devices–the Impact of Electrostatic Potentials
The generation of free charges in organic semiconductors is fundamentally limited by the formation of tightly bound electron‐hole pairs (excitons) arising from their low dielectric screening. Conventional donor/acceptor (D/A) heterojunctions overcome this limitation through interfacial energetic offsets at the cost of high voltage losses that limit organic photoconversion device efficiency compared to inorganic counterparts. The success of non‐fullerene acceptors (NFAs), enabling efficient charge generation at relatively small energetic offsets, challenges this picture and suggests the need to consider additional charge generation mechanisms. In this review, we highlight the critical role of molecular electrostatic potentials in free charge generation within organic semiconductors. The molecular origins of electrostatic potentials are discussed within the multipole expansion framework, with particular emphasis on quadrupole moments arising from anisotropic charge distributions within a molecule. The role of these electrostatic effects in modulating interfacial energetics, inducing band bending, and facilitating charge separation in donor/acceptor heterojunctions is examined, alongside their extension to single‐component systems. In single‐component systems, orientation‐dependent molecular packing creates functional energetic offsets without the need for distinct donor and acceptor materials. Based on these observations, key molecular and device design strategies for harnessing electrostatic effects in next‐generation organic photoconversion devices are outlined.
- Open Access
- 12 November 2025
- Published by Wiley in Advanced Optical Materials
- Vol. 13 (36)
Efficient Non‐Fullerene Acceptor‐Based Organic Photodetectors Achieved by Reduced Deep Traps in Highly Intermixed Co‐Evaporated Bulk‐Heterojunction Blends
Organic photodetectors (OPDs) based on co‐evaporated bulk heterojunctions (BHJs) have demonstrated their potential for industrially relevant fabrication of high‐efficiency devices. However, acceptor materials choice is still dominated by fullerenes, which show sub‐optimal performance due to deep trap states originating from unfavorable BHJ morphology. Herein, the non‐fullerene acceptor Cl 6 ‐SubPc is used to replace C 60 in 2‐((8‐methyl‐8H‐thieno[2,3‐b]indol‐2‐yl)methylene)−1H‐cyclopenta[b]naphtha‐lene‐1,3(2H)‐dione (MPTA):C 60 BHJs. Through active layer thickness tuning, the effective Cl 6 ‐SubPc intercalation into MPTA domains is achieved for a highly intermixed BHJ morphology. This results in a high yield of interfacial charge‐transfer states, which are readily quenched under electric field for efficient OPD photoresponse. In comparison to C 60 ‐based devices, Cl 6 ‐SubPc suppresses the residual MPTA aggregation and the adduct generation with MPTA, preventing deep‐trap state formation. As such, non‐fullerene acceptor‐based OPDs are highly promising for trap‐free photodetection, enabling superior performances under low‐light illumination.
- 12 November 2025
- Published by Wiley in Advanced Optical Materials
- Vol. 13 (36)
Open AccessEfficient Non‐Fullerene Acceptor‐Based Organic Photodetectors Achieved by Reduced Deep Traps in Highly Intermixed Co‐Evaporated Bulk‐Heterojunction Blends
Organic photodetectors (OPDs) based on co‐evaporated bulk heterojunctions (BHJs) have demonstrated their potential for industrially relevant fabrication of high‐efficiency devices. However, acceptor materials choice is still dominated by fullerenes, which show sub‐optimal performance due to deep trap states originating from unfavorable BHJ morphology. Herein, the non‐fullerene acceptor Cl 6 ‐SubPc is used to replace C 60 in 2‐((8‐methyl‐8H‐thieno[2,3‐b]indol‐2‐yl)methylene)−1H‐cyclopenta[b]naphtha‐lene‐1,3(2H)‐dione (MPTA):C 60 BHJs. Through active layer thickness tuning, the effective Cl 6 ‐SubPc intercalation into MPTA domains is achieved for a highly intermixed BHJ morphology. This results in a high yield of interfacial charge‐transfer states, which are readily quenched under electric field for efficient OPD photoresponse. In comparison to C 60 ‐based devices, Cl 6 ‐SubPc suppresses the residual MPTA aggregation and the adduct generation with MPTA, preventing deep‐trap state formation. As such, non‐fullerene acceptor‐based OPDs are highly promising for trap‐free photodetection, enabling superior performances under low‐light illumination.
- Open Access
- 25 June 2022
- Published by Wiley in Advanced Energy Materials
- Vol. 12 (30)
Strong Intermolecular Interactions Induced by High Quadrupole Moments Enable Excellent Photostability of Non‐Fullerene Acceptors for Organic Photovoltaics
Understanding degradation mechanisms of organic photovoltaics (OPVs) is a critical prerequisite for improving device stability. Herein, the effect of molecular structure on the photostability of non‐fullerene acceptors (NFAs) is studied by changing end‐group substitution of ITIC derivatives: ITIC, ITIC‐2F, and ITIC‐DM. Using an assay of in situ spectroscopy techniques and molecular simulations, the photodegradation product of ITIC and the rate of product formation are identified, which correlates excellently to reported device stability, with ITIC‐2F being the most stable and ITIC‐DM the least. The choice of acceptor is found to affect both the donor polymer (PBDB‐T) photostability and the morphological stability of the bulk heterojunction blend. Molecular simulations reveal that NFA end‐group substitution strongly modulates the electron distribution within the molecule and thus its quadrupole moment. Compared to unsubstituted‐ITIC, end‐group fluorination results in a stronger, and demethylation a weaker, molecular quadrupole moment. This influences the intermolecular interactions between NFAs and between the NFA and the polymer, which in turn affects the photostability and morphological stability. This hypothesis is further tested on two other high quadrupole acceptors, Y6 and IEICO‐4F, which both show impressive photostability. The strong correlation observed between NFA quadrupole moment and photostability opens a new synthetic direction for photostable organic photovoltaic materials.
- 25 June 2022
- Published by Wiley in Advanced Energy Materials
- Vol. 12 (30)
Open AccessStrong Intermolecular Interactions Induced by High Quadrupole Moments Enable Excellent Photostability of Non‐Fullerene Acceptors for Organic Photovoltaics
Understanding degradation mechanisms of organic photovoltaics (OPVs) is a critical prerequisite for improving device stability. Herein, the effect of molecular structure on the photostability of non‐fullerene acceptors (NFAs) is studied by changing end‐group substitution of ITIC derivatives: ITIC, ITIC‐2F, and ITIC‐DM. Using an assay of in situ spectroscopy techniques and molecular simulations, the photodegradation product of ITIC and the rate of product formation are identified, which correlates excellently to reported device stability, with ITIC‐2F being the most stable and ITIC‐DM the least. The choice of acceptor is found to affect both the donor polymer (PBDB‐T) photostability and the morphological stability of the bulk heterojunction blend. Molecular simulations reveal that NFA end‐group substitution strongly modulates the electron distribution within the molecule and thus its quadrupole moment. Compared to unsubstituted‐ITIC, end‐group fluorination results in a stronger, and demethylation a weaker, molecular quadrupole moment. This influences the intermolecular interactions between NFAs and between the NFA and the polymer, which in turn affects the photostability and morphological stability. This hypothesis is further tested on two other high quadrupole acceptors, Y6 and IEICO‐4F, which both show impressive photostability. The strong correlation observed between NFA quadrupole moment and photostability opens a new synthetic direction for photostable organic photovoltaic materials.
- Open Access
- 15 December 2021
- Published by Wiley in Advanced Energy Materials
- Vol. 12 (3) , 2103237
Organic Bilayer Photovoltaics for Efficient Indoor Light Harvesting
Indoor organic photovoltaics (OPVs) are a potential niche application for organic semiconductors due to their strong and well‐matched absorption with the emission of indoor lighting. However, due to extremely low photocurrent generation, the device parameters critical for efficient indoor OPVs differ from those under 1 Sun conditions. Herein, these critical device parameters—recombination loss and shunt resistance (Rsh)—are identified and it is demonstrated that bilayer OPVs are suitable for indoor PV applications. Compared to bulk‐heterojunction (BHJ), the open‐circuit voltage loss of bilayer devices under low light intensities is much smaller, consistent with a larger surface photovoltage response, indicating suppressed recombination losses. The bilayer devices show a higher fill factor at low light intensities, resulting from high Rsh afforded by the ideal interfacial contacts between the photoactive and the charge transport layers. The high Rsh enables bilayer devices to perform well without a light‐soaking process. Finally, the charge carriers are extracted rapidly in bilayers, which are attributed to strongly suppressed trap states possibly induced by isolated domains and non‐ideal interfacial contacts in BHJs. This study highlights the excellent suitability of bilayer OPVs for indoor applications and demonstrates the importance of device architecture and interfacial structures for efficient indoor OPVs.
- 15 December 2021
- Published by Wiley in Advanced Energy Materials
- Vol. 12 (3) , 2103237
Open AccessOrganic Bilayer Photovoltaics for Efficient Indoor Light Harvesting
Indoor organic photovoltaics (OPVs) are a potential niche application for organic semiconductors due to their strong and well‐matched absorption with the emission of indoor lighting. However, due to extremely low photocurrent generation, the device parameters critical for efficient indoor OPVs differ from those under 1 Sun conditions. Herein, these critical device parameters—recombination loss and shunt resistance (Rsh)—are identified and it is demonstrated that bilayer OPVs are suitable for indoor PV applications. Compared to bulk‐heterojunction (BHJ), the open‐circuit voltage loss of bilayer devices under low light intensities is much smaller, consistent with a larger surface photovoltage response, indicating suppressed recombination losses. The bilayer devices show a higher fill factor at low light intensities, resulting from high Rsh afforded by the ideal interfacial contacts between the photoactive and the charge transport layers. The high Rsh enables bilayer devices to perform well without a light‐soaking process. Finally, the charge carriers are extracted rapidly in bilayers, which are attributed to strongly suppressed trap states possibly induced by isolated domains and non‐ideal interfacial contacts in BHJs. This study highlights the excellent suitability of bilayer OPVs for indoor applications and demonstrates the importance of device architecture and interfacial structures for efficient indoor OPVs.
- 1 November 2020
- Published by Elsevier in Nano Energy
- Vol. 77
Aesthetic and colorful: Dichroic polymer solar cells using high-performance Fabry-Pérot etalon electrodes with a unique Sb2O3 cavity
- 1 November 2020
- Published by Elsevier in Nano Energy
- Vol. 77
Aesthetic and colorful: Dichroic polymer solar cells using high-performance Fabry-Pérot etalon electrodes with a unique Sb2O3 cavity
- 15 March 2019
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 7 (15) , 4559-4566
Synergistic combination of amorphous indium oxide with tantalum pentoxide for efficient electron transport in low-power electronics
Among transparent metal oxide semiconductors, systems based on indium oxide currently deliver the best combination of electronic characteristics and optical transmittance, outperforming even the well-established polycrystalline silicon devices. Indium oxide has the unique property that uniform, amorphous films yield superior electronic properties compared to microcrystalline films; for this reason, Ga and Zn hetero-elements are usually added to disrupt crystallization and result in uniformly disordered films. However, dopants have a general tendency to increase the complexity and decrease the mobility of semiconductors and their addition might well be avoided if high-quality, amorphous In2O3 films could be grown without them. In this work, we show that this problem can be resolved by exploiting a synergistic interaction between solution-processed indium oxide (In2O3) and underlying tantalum pentoxide (Ta2O5) dielectric films. We observed that amorphous Ta2O5 inhibits crystallization of In2O3 leading to high-quality amorphous thin films with reduced oxygen deficiencies at the semiconductor/dielectric interface. Transparent Ta2O5/In2O3 TFTs with very low operating voltages were demonstrated with effective field-effect mobilities of up to 23.1 cm2 V−1 s−1 at only 3 V drain–source voltage (VDS) using this approach. Additionally, the suppressed carrier density arising from reduced oxygen deficiencies reduced the drain current at 0 V gate bias (I0) by six orders of magnitude from 0.25 mA to 10.8 nA, compared to a SiO2 reference device. These results highlight the importance of considering an underlying dielectric layer to maximize device performance.
- 15 March 2019
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 7 (15) , 4559-4566
Synergistic combination of amorphous indium oxide with tantalum pentoxide for efficient electron transport in low-power electronics
Among transparent metal oxide semiconductors, systems based on indium oxide currently deliver the best combination of electronic characteristics and optical transmittance, outperforming even the well-established polycrystalline silicon devices. Indium oxide has the unique property that uniform, amorphous films yield superior electronic properties compared to microcrystalline films; for this reason, Ga and Zn hetero-elements are usually added to disrupt crystallization and result in uniformly disordered films. However, dopants have a general tendency to increase the complexity and decrease the mobility of semiconductors and their addition might well be avoided if high-quality, amorphous In2O3 films could be grown without them. In this work, we show that this problem can be resolved by exploiting a synergistic interaction between solution-processed indium oxide (In2O3) and underlying tantalum pentoxide (Ta2O5) dielectric films. We observed that amorphous Ta2O5 inhibits crystallization of In2O3 leading to high-quality amorphous thin films with reduced oxygen deficiencies at the semiconductor/dielectric interface. Transparent Ta2O5/In2O3 TFTs with very low operating voltages were demonstrated with effective field-effect mobilities of up to 23.1 cm2 V−1 s−1 at only 3 V drain–source voltage (VDS) using this approach. Additionally, the suppressed carrier density arising from reduced oxygen deficiencies reduced the drain current at 0 V gate bias (I0) by six orders of magnitude from 0.25 mA to 10.8 nA, compared to a SiO2 reference device. These results highlight the importance of considering an underlying dielectric layer to maximize device performance.
- Open Access
- 28 November 2018
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 8 (69) , 39777-39783
Non-halogenated diphenyl-chalcogenide solvent processing additives for high-performance polymer bulk-heterojunction solar cells
The ability to control the morphologies of active layers is a critical factor in the successful development of polymer solar cells (PSCs), and solvent processing additives offer a simple and effective way to accomplish this. In particular, diphenyl ether (DPE) is one of the most effective solvent additives but analogous additives based on this structure have not yet been extensively investigated. In this work, we have fabricated PSCs and investigated photovoltaic device characteristics using the series of non-halogenated, diphenyl-chalcogen solvent additives; DPE, diphenyl sulfide (DPS) and diphenyl selenide (DPSe). DPS devices showed optimal power conversion efficiencies (PCEs) of up to 9.08%, and DPE devices also showed similarly high PCEs of up to 8.85%. In contrast, DPSe devices showed relatively low PCEs (5.45% at best) which we attribute to significant surface recombination and high series resistance, which led to limited open-circuit voltage (VOC). In the case of DPS, fast, field-independent photocurrent saturation with negligible bimolecular recombination led to efficient charge separation and collection, which resulted in the highest PCEs. Additionally, using 1,2,4-trimethylbenzene and DPS as an entirely non-halogenated solvent/additive system, we successfully demonstrated device fabrication with comparably high PCEs of up to 8.4%. This work elucidates the effects of diphenyl-based solvent additives in PSCs and suggests a great potential of DPS as an effective non-halogenated solvent additive.
- 28 November 2018
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 8 (69) , 39777-39783
Open AccessNon-halogenated diphenyl-chalcogenide solvent processing additives for high-performance polymer bulk-heterojunction solar cells
The ability to control the morphologies of active layers is a critical factor in the successful development of polymer solar cells (PSCs), and solvent processing additives offer a simple and effective way to accomplish this. In particular, diphenyl ether (DPE) is one of the most effective solvent additives but analogous additives based on this structure have not yet been extensively investigated. In this work, we have fabricated PSCs and investigated photovoltaic device characteristics using the series of non-halogenated, diphenyl-chalcogen solvent additives; DPE, diphenyl sulfide (DPS) and diphenyl selenide (DPSe). DPS devices showed optimal power conversion efficiencies (PCEs) of up to 9.08%, and DPE devices also showed similarly high PCEs of up to 8.85%. In contrast, DPSe devices showed relatively low PCEs (5.45% at best) which we attribute to significant surface recombination and high series resistance, which led to limited open-circuit voltage (VOC). In the case of DPS, fast, field-independent photocurrent saturation with negligible bimolecular recombination led to efficient charge separation and collection, which resulted in the highest PCEs. Additionally, using 1,2,4-trimethylbenzene and DPS as an entirely non-halogenated solvent/additive system, we successfully demonstrated device fabrication with comparably high PCEs of up to 8.4%. This work elucidates the effects of diphenyl-based solvent additives in PSCs and suggests a great potential of DPS as an effective non-halogenated solvent additive.
- 2 May 2017
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 10 (6) , 1443-1455
High-efficiency photovoltaic cells with wide optical band gap polymers based on fluorinated phenylene-alkoxybenzothiadiazole
A new series of wide band gap photovoltaic polymers based on a fluorinated phenylene-alkoxybenzothiadiazole unit with an optical band gap of over 1.90 eV are designed and utilized for high-performance single- and multi-junction bulk heterojunction polymer solar cells.
- 2 May 2017
- Published by Royal Society of Chemistry (RSC) in Energy & Environmental Science
- Vol. 10 (6) , 1443-1455
High-efficiency photovoltaic cells with wide optical band gap polymers based on fluorinated phenylene-alkoxybenzothiadiazole
A new series of wide band gap photovoltaic polymers based on a fluorinated phenylene-alkoxybenzothiadiazole unit with an optical band gap of over 1.90 eV are designed and utilized for high-performance single- and multi-junction bulk heterojunction polymer solar cells.
- 1 March 2017
- Published by Springer Nature in Science China Chemistry
- Vol. 60 (4) , 528-536
Semi-crystalline photovoltaic polymers with siloxane-terminated hybrid side-chains
- 1 March 2017
- Published by Springer Nature in Science China Chemistry
- Vol. 60 (4) , 528-536
Semi-crystalline photovoltaic polymers with siloxane-terminated hybrid side-chains
- 19 September 2016
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 4 (42) , 16410-16417
High-efficiency, hybrid Si/C60 heterojunction solar cells
The first high-efficiency hybrid solar cell of its type comprising p-type silicon with an organic n-type C60 layer is demonstrated.
- 19 September 2016
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 4 (42) , 16410-16417
High-efficiency, hybrid Si/C60 heterojunction solar cells
The first high-efficiency hybrid solar cell of its type comprising p-type silicon with an organic n-type C60 layer is demonstrated.