KSKateryna Sai

Kateryna Sai

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Kateryna Sai has a total of 55 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Energy-based substantiation of carbon gasification modes in carbon-containing waste

    by Andriy Helesh, Pavlo Saik, Nazar Lysyi, Vasyl Lozynskyi, Mykhailo Petlovanyi, Kateryna Sai

    Purpose. The research aims to theoretically substantiate the energy-efficient gasification modes of carbon component in carbon-containing waste based on unified thermal self-sufficiency indicators, using coal mining waste as a basic example for model application. Methods. Comparative material and thermal calculations for four idealized carbon conversion routes within the 660-1000°C temperature range were performed based on previously determined equilibrium constants. All specific indicators refer to 1 kg of initial C. The basic comparison was conducted at an absolute pressure of about 0.2533 MPa. The influence of pressure was investigated for steam and CO2-gasification within the 0.1013-1.0133 MPa. The comparison of heat requirement qreq, resource qres, difference qnet = qres – qreq, the coefficient of potential heat coverage KTSS and the lower heating value of the gas was performed taking into account the residual steam. Findings. At pabs = 0.2533 MPa for C + H2O ↔ CO + H2, thermal self-sufficiency coefficient for endothermic processes reaches 2.17 at 860°C, 2.19 at 960°C and slightly decreases to 2.187 at 1000°C. For C + CO2 ↔ 2CO, it grows to 2.35 at 1000°C. Incomplete air oxidation provides the highest qnet, however, the lower heating value of the product gas (LHVg) remains stable low in the entire examined temperature range of 4.39 MJ/nm3 due to the dilution of combustible gases with air nitrogen (N2). Increasing pabs from 0.1013 to 1.0133 MPa worsens the equilibrium values of steam and carbon dioxide conversions. Originality. On the joint basis of 1 kg of initial C, the temperature dependences of the energy potential and heat requirement of idealized gasification routes are quantified. A single system qreq – qres – qnet – KTSS is proposed for a correct comparison of exo- and endothermic carbon gasification routes. It is shown that the advantage of the route depends on the chosen criterion: H2 yield, CO formation, volumetric heating value or potential thermal self-sufficiency. The relationship between pressure influence, equilibrium conversion and dilution of the product gas is clarified. Practical implications. The criteria for pre-selection of the route are proposed, based on the intended use of gas and available heat resources. For steam gasification at the base pressure, the initial test range of 860-900°C is recommended; for target production of CO in the presence of high-temperature heat – CO2-conversion in the 900-1000°C range is recommended. For the hydrogen product, it is advisable to combine steam gasification with water-gas shift reaction, and for the autothermal scheme – to determine the share of oxidant introduced into the system.

  • Open Access

    Research into the granulometric, chemical and mineralogical characteristics of coal mining waste as incoming raw materials to the gasification process

    by M. V. Petlovanyi, V. H. Lozynskyi, P. B. Saik, K. S. Sai

    The research aims to assess the potential of coal mine waste rocks as an initial technogenic raw material for the gasification process, in terms of their granulometric and chemical-mineralogical composition. The research focuses on an experimental study of the granulometric composition of the waste rock dump, the ratio of coal and rock components within certain size classes, and the composition of the rock’s chemical and mineral parts. It also focuses on signs of the presence of rare and rare-earth elements. A heterogeneous, polyfractional waste rock structure, with a predominance of medium- and fine-sized material, has been identified. The mineral component was found to dominate the dump mass, but the residual coal fractions were found to have a noticeable energy potential and to be unevenly distributed between size classes. Certain medium and fine fractions have been proven to contribute most to the coal resource, while the largest classes, which contain no coal should be separated during raw material preparation. A similar aluminosilicate base has been identified in the mineral matrix of all size classes. The main determined phases are quartz, kaolinite, mica minerals and feldspars. The presence of Y, Ga and Sc, as well as signs of possible lanthanides, has been detected in the waste rocks, which may become concentrated in the solid residue following thermochemical conversion. The theoretical significance of the results lies in investigating granulometric and chemical-mineralogical composition of the initial technogenic raw material to identify its fundamental changes and transformations under the influence of thermochemical processes. The practical significance of this research lies in developing a comprehensive approach to the technogenic waste processing, specifically through the combined production of producer gas, extraction of valuable metals from the enriched thermally modified residue, and the use of depleted slag in various fields of the construction industry. The implementation of a coal mining waste gasification strategy creates the conditions for the gradual elimination of waste rock dumps, thereby reducing the their environmental impact and facilitating the adoption of circular economy principles in coal mining regions.

  • Assessment of the impact of iron-ore tailings dams on water resources and new methods for beneficiation waste utilization

    by Мykhailo V. Petlovanyi, Kateryna S. Sai, Vasyl H. Lozynskyi, Yurii V. Buchavyi, Pavlo B. Saik

    Iron ore beneficiation is accompanied by the formation of large tailings dams containing finely dispersed waste, the open storage of which near surface water resources poses a direct threat to the hydrosphere and requires effective measures to minimize environmental risks. The research aims to assess the impact of tailings dams on surface water quality in relation to climatic factors and to substantiate the environmental feasibility of converting tailings into paste backfill mixtures and monolithic mass. The methodology combines statistical analysis and interpretation of hydrochemical monitoring data for the Inhulets River (2024–2025) upstream and in the zone influenced by the tailings dam, along with laboratory tests of waste leaching with deionized water to determine their migration potential. Dynamic changes in the migration of sulfates and chlorides depending on the phase state of precipitation and temperature regime have been identified. It has been proven that open storage causes salt pollution of the river: during heavy rainfall and snowmelt, the concentration of sulfates increases by 2.6 times, and chlorides – by 2.0 times. Experiments have shown that under conditions of extreme leaching, dispersed tailings are a source of secondary pollution, forming the release of iron, biogenic compounds, and toxic metals that exceed the maximum permissible concentration (MPC) for water bodies. It has been found that the transformation of finely dispersed beneficiation tailings into a monolithic paste mass creates a reliable geochemical barrier with 100% immobilization of heavy metals in the cement matrix and a 30–40% reduction in iron migration. Based on the environmental safety of the backfill mass for groundwater, a new direction for beneficiation waste utilization has been proposed to comprehensively fill underground cavities by converting them into a monolithic state, which will gradually reduce the area of surface storage and the risk of water resource pollution, while ensuring the protection of subsoil resources.

  • Predicting the geofiltration processes within the closed quarry zone in difficult technogenically disturbed conditions

    by Ye. A Sherstiuk, M. V Petlovanyi, K. S Sai

    Purpose. The research purpose is a predictive assessment of the water content of the mined-out quarry cavity under conditions of simultaneous technogenic impact of active quarries and mines based on numerical modeling of geofiltration processes to determine the probability of contact and water saturation of the formed backfill mass over time. Methodology. A numerical geofiltration model implemented in the MODFLOW software package is used to study the hydrodynamic regime of a specified site in the Kryvyi Rih region, where a closed quarry is located, planned for backfilling. The solution of inverse and prognostic problems is applied, in the course of which the adequacy of reflecting the hydrodynamic conditions of the studied area in the geofiltration model has been determined, as well as the predicted rates and nature of the level restoration at the mining site have been obtained. Findings. A complex model of geofiltration processes has been developed and tested, taking into account the technogenic impact of operating quarry and mines, which makes it possible to assess the nature of groundwater level restoration in dynamics. It has been found that in the current situation of the hydrodynamic groundwater regime at the site, the greatest impact is caused by drainage dewatering of mines, which has led to the formation of depression cones and groundwater discharge in a large active quarry and a closed quarry planned for backfilling. It has been determined that if the drainage dewatering of all mining enterprises is completely stopped, which is unlikely, the groundwater level restoration in a closed quarry can occur no earlier than in 50 years, while the dependence of the groundwater level restoration over time is logarithmic. Originality. Based on the modeling of geofiltration processes, an assessment of the groundwater level restoration in a closed quarry is provided during the development of various scenarios for the cessation of dewatering at mining enterprises that have a significant technogenic impact on the hydrodynamic regime. It has been proven that when backfilling the mined-out space of a closed quarry, a monolithic backfill mass will not be prone to a decrease in physical-mechanical characteristics from the influence of aquifers, which will ensure its long-term geomechanical reliability. Practical value. A methodology has been developed for modeling geofiltration processes and restoring the groundwater level of a closed quarry, taking into account the difficult complex technogenic impact of various mining enterprises. The results obtained are important for the predictive assessment of the probability of water saturation of the backfill mass in the quarry cavity and planning of engineering-geological measures for its isolation.


  • Research into cemented paste backfill properties and options for its application: Case study from a Kryvyi Rih Iron-ore Basin, Ukraine

    by Mykhailo Petlovanyi, Kateryna Sai

    Purpose. The purpose is to conduct experimental research on a set of properties of cemented paste backfill mass based on a number of natural-technogenic materials of the Kryvyi Rih Iron-ore Basin with the aim of its further use in technologies for restoring a heavily disturbed earth's surface by complex iron ore mining. Methods. A comprehensive toolkit is used: X-ray fluorescence and X-ray diffraction analyses to study the chemical and mineralogical composition of the components, conductometer measurements of the electrical conductivity of the mixtures during their hardening, laboratory studies of the formulations of paste backfill mixtures and determination of their physical-mechanical characteristics using a laboratory hydraulic press, an analytical study to determine suitable regions for paste backfilling, taking into account the presence of technogenic cavities, tailings dumps and binder materials. Findings. It has been found that a paste-like homogeneous state of the backfill mixture using iron ore beneficiation tailings from mining and processing plants of Ukraine is achieved at a solid part content of about 73-75%, which provides an optimal balance between its flowability and mechanical strength. A set of patterns of strength changes depending on the binder material dosage, solid part content and hardening period for paste backfill mixture based on pure cement and with different variations of alternative binder materials has been determined. The patterns have been revealed of the correlation between the paste backfill mixture strength and the electrical conductivity parameters. Originality. A method for predicting the early and late strength of paste backfilling has been developed, based on the identified patterns between the electrical conductivity of the paste mixture, the time to reach its peak, and the strength at different stages of hardening. The knowledge and understanding of the physical-mechanical properties of cemented paste backfill mixture in the conditions of hardening under the influence of climatic environmental conditions have been further developed. Practical implications. The conducted research on the properties of paste backfilling is useful for designing a technology for restoring heavily disturbed earth’s surface, namely, backfilling of failure zones of the earth’s surface from the influence of iron ore mines, backfilling of identified underground unfilled cavities of closed mines and mined-out spaces of closed quarries. A concept for implementing a paste backfilling in the western part of the city of Kryvyi Rih has been developed, which is expected to contribute to the environmental, economic and social development of the region.


  • Open Access

    Studying the geotechnical stability of the earth’s surface during the formation of different backfill mass types in quarry cavities

    by Мykhailo V. Petlovanyi, Kateryna S. Sai, Vasyl V. Popovych, Oleksii V. Khalymendyk, Vladyslav V. Ruskykh

    The research focuses on studying the geotechnical stability of backfill mass in the mined-out spaces of inactive quarries for restoring the earth’s surface in the conditions of the Kryvyi Rih region, where large-scale complex iron ore mining is conducted. Based on the analysis, it has been determined that in the region, to fill inactive quarry cavities and failure zones, the traditional method of filling them with dump waste rock is used. Given that the city of Kryvyi Rih is a densely populated, highly indutrialised agglomeration, the restoration of additional land areas could bring significant benefits for the economic development of the region, but the rock mass is not able to provide reliable geomechanical stability of the earth’s surface. The transformation of the physical state of the backfill mass from a loose to a monolithic state is proposed. In order to select alternative backfill methods, the quantitative and qualitative structure of the accumulated wastes of the mining-metallurgical complex that can be used as backfill materials is analyzed. Taking into account the significant volumes of accumulated beneficiation tailings and their limited utilization, it is recommended to use them as part of cemented paste backfilling, which will lead to an improvement in the environmental situation. The research methodology consists of laboratory tests of physical-mechanical properties of dump hard rocks, analysis of the properties of paste backfilling, and numerical modeling of stability of various types of backfill masses. It has been found that the mixture of rocks of 0...100 mm in terms of bulk density and voidness is close to the minimum fraction of 0...5 mm, which does not require the need to select a certain fractional composition. A «stress-strain» curve of a 0...100 mm rock mixture with a logarithmic relationship, characterized by three stages of strain, has been plotted. The strain modulus value has been calculated. The similarity of the mechanical characteristics of the studied mixture to the full-scale characteristics of dump hard rocks is substantiated. The modeling results show that the maximum strains in the case of rock backfilling reach 780 mm, while the calculations of paste backfilling show a significant decrease in the subsidence value, reaching only 43 mm. The difference in the values of subsidence is due to a significant difference in physical-mechanical properties. Based on studying the hardening conditions of paste backfill mixtures and temperature dynamics in the region, a seasonal approach and the formation of a combined backfill mass are proposed to maintain the reclamation rate. The research findings are valuable for the development of the construction direction of reclamation in the Kryvyi Rih region and the rational use of restored land areas.

  • COMPREHENSIVE PROCESSING OF MINERAL RAW MATERIALS FROM COAL MINE WASTE DUMPS: PROPERTIES, VALUABLE PRODUCTS, AND RESOURCE ACCOUNTING SYSTEM

    by Mykhailo Petlovanyi, Kateryna Sai, Oleksandr Dreshpak, Maksym Demydov

    Objective. Experimental studies on the chemical and mineralogical composition of coal mine spoil heaps and the potential for processing them to obtain valuable mineral-raw materials. Development of an analytical tool for accounting and forecasting the resource potential of coal mine spoil heaps. Methods. To achieve the objective, X-ray fluorescence analysis, X-ray phase analysis, granulometric analysis, laboratory studies of mineral raw material enrichment using sieve fractionation and gravity separation, as well as analytical studies of spoil heap resource accounting were employed. Results. The chemical, mineralogical, and granulometric composition of spoil heaps from a coal mine in the Western Donbas region was investigated, enabling the identification of a processing strategy to obtain a range of products: coal concentrate, crushed stone mixture, sand fraction, and clay fraction. It was established that gravity separation of coarse fractions in a heavy medium created with clay slurry demonstrated high separation efficiency, yielding a significant low-ash coal fraction and a high-ash rock fraction. In contrast, spiral separator processing demonstrated significantly lower low-ash coal recovery. A technological processing scheme for spoil heaps to obtain a complex of valuable products was developed, and forecast indicators were evaluated. A methodological system for accounting the resource potential of a coal mine waste dump has been proposed in the form of an informational database. This system allows for tracking changes in the dumps structure, identifying zones of attractive resource accumulation for economic efficiency of processing operations in the long term. Scientific novelty. The use of clay suspension from washed spoil heaps to create a heavy medium for the beneficiation of coarse fractions allows for the recovery of up to 95% coal concentrate with 11% ash content, contributing to resource conservation. Practical significance. A technological scheme for obtaining a range of valuable products for the energy and construction industries has been developed. An analytical tool for resource potential accounting and calendar planning for spoil heap formation has been created, enabling operational identification of resource concentration zones within spoil heaps and their sections. Keywords: coal mine, spoil heap, valuable resource, chemical composition, mineralogical composition, granulometric composition, gravity separation, resource accounting.

  • Open Access

    Methodological approach to determining promising “quarry cavities – backfill material” systems on the territory of Ukraine

    by Mykhailo V. Petlovanyi, Kateryna S. Sai, Vasyl V. Popovych, Maksym O. Chebanov

    The research is aimed at identifying promising “quarry cavities – backfill material” systems on the territory of Ukraine. Currently, the existing reclamation methods for quarry cavities do not provide for the earth’s surface level complete restoration. A number of industrial wastes, the accumulation of which is increasing rapidly, are potential backfill materials. An insufficiently studied and promising method for restoring the earth’s surface level is the formation of a backfill mass in quarry cavities, which can provide geomechanical stability. Nevertheless, in order to develop directions for backfilling, it is necessary to have information on the spatial distribution of quarry cavities and potential backfill materials on the territory of Ukraine, which is also insufficiently studied today. The paper forms and reveals a theoretical idea about the “quarry cavities – backfill material” systems. A number of important conditions for the harmonious existence and effective implementation of the specified promising systems are characterized. The methodology for creating the basis of an information-analytical map is presented, and the principles for determining and characterizing its main constituent elements are given. A new information-analytical map of the spatial location of potential backfill materials and formed quarry cavities on the territory of Ukraine has been created, on the basis of which possible “quarry cavities – backfill material” systems have been identified. It has been determined that today on the territory of Ukraine, for the earth’s surface level complete restoration, it is expedient to consider the formation of a backfill mass in quarry cavities in 12 districts, where there are promising “quarry cavities – backfill material” systems. The concept of a complete restoration development of the earth’s surface disturbed by mining operations in certain potential systems is possible under conditions of synergistic interaction between public authorities and private business. The practical result obtained is an important basis for creating an effective mechanism and effective measures for a complete restoration of the earth’s surface state, which will contribute to strengthening the international image of Ukraine as a responsible and environmentally conscious country.

  • Open Access

    A new approach to producing a prospective energy resource based on coalmine methane

    by K S Sai, M V Petlovanyi, D S Malashkevych

    The paper describes topical issues of a prospective method for coalmine methane utilization for obtaining an additional valuable energy resource for the regional development of coal-mining areas. It is noted that the development of the extraction of methane resources is very urgent and is of great economic importance for ensuring the energy independence of Ukraine. The experience and technologies of using methane and coalmine gas by global coal-mining companies are analyzed. Modern prospects and opportunities for using coal gas are studied. There is a need to transform the coalmine methane removal system and directions for maximizing the use of its resources in a wide range of concentrations in the composition of gas-air mixtures based on the development of innovative technologies to improve the efficiency and cost-effectiveness of functioning coal-mining enterprises. Attention is focused on the advantages of using gas hydrate technologies for obtaining additional energy resource under conditions of changing coalmine methane concentrations. The specifics of the process of mixed gas hydrate formation from gas mixtures of various geneses have been studied. It has been revealed that it is the coalmine gas-methane composition that determines and forms the basic condition for hydrate formation. The thermobaric conditions for the hydrate formation process at different methane concentrations in gas mixtures of degassing systems have been experimentally determined. The results obtained are the basis for further research on efficiency of creating gas hydrates from coalmine methane and determining its minimum permissible concentration in the gas mixture of degassing systems according to the technological and economic criteria of hydrate formation.


  • Analytical research of the parameters and characteristics of new “quarry cavities – backfill material” systems: Case study of Ukraine

    by Mykhailo Petlovanyi, Kateryna Sai, Oleksii Khalymendyk, Olena Borysovska, Yevheniia Sherstiuk

    Purpose. The research is aimed to identify, investigate and study the parameters and characteristics of the “quarry cavities – backfill material” systems on the territory of Ukraine using new comprehensive methodological tools that form the basis for the development of effective methods for restoring the earth’s surface with an emphasis on industrial and construction use. Methods. An integrated approach is used, which includes: analysis of the spatial location of industrial waste heaps on the territory of Ukraine as potential backfill materials and resulting quarry cavities that are not subject to complete earth’s surface restoration, as well as determination of the volumes of resulting cavities and backfill materials. Based on a set of factors, the “quarry cavities – backfill material” systems have been ranked according to priority. Tools used are: information data from the State Informational Geological Fund of Ukraine, registers of industrial waste accumulation sites in region, the Google Earth satellite program, an online topographic map (OpenStreetMap) and Blender program for constructing 3D models. Findings. A new concept and theoretical representation of “quarry cavities – backfill material” has been formulated. The characteristics of a number of important conditions for the harmonious existence and effective implementation of promising “quarry cavities – backfill material” systems are provided. A new information-analytical map of the spatial location of potential backfill materials and resulting quarry cavities has been created. Thirteen promising systems and their parameters have been identified, within which it is appropriate to consider backfill technologies for the complete earth’s surface restoration. The existing balance of cavities and backfill materials for the identified systems has been determined, followed by grading of quarries according to the predicted lifespan. Originality. The “quarry cavities – backfill material” systems, which have the greatest advantages, are specified by ranking them according to a complex of technological, environmental, economic and social factors. Practical implications. The results obtained provide valuable information for the development of a government strategy and environmental programs for the restoration of land areas disturbed by mining operations based on backfill technologies and their subsequent use for industrial purposes.