Abdulaziz Alsaif
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Abdulaziz Alsaif has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Yassir M. Abbas
Department of Civil Engineering, College of Engineering, King Saud University, Riyadh, Saudi Arabia
9 shared publications - Kypros Pilakoutas
The University of Sheffield
5 shared publications - Maurizio Guadagnini
The University of Sheffield
5 shared publications Abdulrahman Albidah
3 shared publications- Abdulrahman S. Albidah
Department of Civil Engineering, King Saud University, Riyadh, Saudi Arabia
2 shared publications Aref Abadel
2 shared publications
Latest Publications
- Open Access
Enhancing Shear Performance of Concrete Beams Using Layered Rubberized and Steel Fiber-Reinforced Composites
Recycling rubber and steel fibers from end-of-life tires for use in structural concrete presents a sustainable pathway to improve resource efficiency and reduce environmental impact. This study assesses the shear performance of reinforced concrete beams in which shredded tire rubber substitutes 20 vol.% of both fine and coarse natural aggregates. The effect of including recycled tire steel fibers (RSF) and industrial steel fibers (ISF), each at a dosage of 20 kg/m3, is also examined. The experimental program involved testing twenty-four cylindrical specimens and seven reinforced concrete beams to evaluate the mechanical and structural behavior of the proposed mixtures. A novel layered concrete configuration is also evaluated, in which rubberized (RU) concrete or steel fiber reinforced rubberized (RUSF) concrete is placed in the tensile zone, and plain (P) concrete is placed in the compressive zone. The results indicate that rubber incorporation alone reduces shear strength by 30.9% compared to P concrete. However, the inclusion of steel fibers not only compensates for this reduction but significantly improves strength and ductility. Beams fully cast with RUSF concrete exhibit a 31.9% increase in shear strength compared to P concrete. In contrast, layered beams with RUSF concrete in the bottom and P concrete in the top show a comparable performance. These findings highlight the potential of integrating steel fiber reinforced rubberized concrete and functional layering to enable the use of substantial quantities of recycled tire materials without compromising structural performance, offering a promising solution for eco-efficient construction.
Open AccessEnhancing Shear Performance of Concrete Beams Using Layered Rubberized and Steel Fiber-Reinforced Composites
Recycling rubber and steel fibers from end-of-life tires for use in structural concrete presents a sustainable pathway to improve resource efficiency and reduce environmental impact. This study assesses the shear performance of reinforced concrete beams in which shredded tire rubber substitutes 20 vol.% of both fine and coarse natural aggregates. The effect of including recycled tire steel fibers (RSF) and industrial steel fibers (ISF), each at a dosage of 20 kg/m3, is also examined. The experimental program involved testing twenty-four cylindrical specimens and seven reinforced concrete beams to evaluate the mechanical and structural behavior of the proposed mixtures. A novel layered concrete configuration is also evaluated, in which rubberized (RU) concrete or steel fiber reinforced rubberized (RUSF) concrete is placed in the tensile zone, and plain (P) concrete is placed in the compressive zone. The results indicate that rubber incorporation alone reduces shear strength by 30.9% compared to P concrete. However, the inclusion of steel fibers not only compensates for this reduction but significantly improves strength and ductility. Beams fully cast with RUSF concrete exhibit a 31.9% increase in shear strength compared to P concrete. In contrast, layered beams with RUSF concrete in the bottom and P concrete in the top show a comparable performance. These findings highlight the potential of integrating steel fiber reinforced rubberized concrete and functional layering to enable the use of substantial quantities of recycled tire materials without compromising structural performance, offering a promising solution for eco-efficient construction.
- Open Access
- 1 November 2025
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1555 (1)
Mechanical and Durability Performance of Cement Mortar Incorporating Polyurethane Powder Waste and Recycled Tire Steel Fibre
This study investigates how using polyurethane (Pu) waste instead of red sand, along with incorporating recycled tire steel fibres (RSF), affects the fresh and hardened properties of cement mortar. Five mortar mixtures were prepared, with Pu replacing sand at levels of 0%, 10%, and 20%, and RSF added at 0% and 1% by volume. The assessed properties included flowability, compressive strength, flexural behaviour, hardened density, and porosity. The results showed that while replacing sand with Pu waste reduced density and compressive strength due to its porous and flexible nature, it offered notable weight reduction benefits. The addition of RSF significantly improved mechanical performance, especially flexural strength, ductility, and toughness, through effective crack bridging and energy dissipation. The mix containing both 20% Pu and RSF exhibited the best performance in terms of flexural toughness and post-crack behaviour. Although Pu increased the porosity of the mortar, RSF helped mitigate this effect, supporting the idea that combining both materials can result in lightweight mortars with acceptable durability and enhanced mechanical performance. Overall, the study highlights the potential use of Pu and RSF in sustainable and lightweight mortar applications.
- 1 November 2025
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 1555 (1)
Open AccessMechanical and Durability Performance of Cement Mortar Incorporating Polyurethane Powder Waste and Recycled Tire Steel Fibre
This study investigates how using polyurethane (Pu) waste instead of red sand, along with incorporating recycled tire steel fibres (RSF), affects the fresh and hardened properties of cement mortar. Five mortar mixtures were prepared, with Pu replacing sand at levels of 0%, 10%, and 20%, and RSF added at 0% and 1% by volume. The assessed properties included flowability, compressive strength, flexural behaviour, hardened density, and porosity. The results showed that while replacing sand with Pu waste reduced density and compressive strength due to its porous and flexible nature, it offered notable weight reduction benefits. The addition of RSF significantly improved mechanical performance, especially flexural strength, ductility, and toughness, through effective crack bridging and energy dissipation. The mix containing both 20% Pu and RSF exhibited the best performance in terms of flexural toughness and post-crack behaviour. Although Pu increased the porosity of the mortar, RSF helped mitigate this effect, supporting the idea that combining both materials can result in lightweight mortars with acceptable durability and enhanced mechanical performance. Overall, the study highlights the potential use of Pu and RSF in sustainable and lightweight mortar applications.
- Open Access
- 11 August 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 38, 2299-2314
Explicit gradient boosting machine for accurate compressive strength prediction of metakaolin-based geopolymer concrete: feature importance and optimization
- 11 August 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 38, 2299-2314
Open AccessExplicit gradient boosting machine for accurate compressive strength prediction of metakaolin-based geopolymer concrete: feature importance and optimization
- Open Access
- 1 January 2025
- Published by Tech Science Press in Computer Modeling in Engineering & Sciences
- Vol. 145 (2) , 1789-1819
Explainable Data-Driven Modeling for Optimized Mix Design of 3D-Printed Concrete: Interpreting Nonlinear Synergies among Binder Components and Proportions
The rapid advancement of three-dimensional printed concrete (3DPC) requires intelligent and interpretable frameworks to optimize mixture design for strength, printability, and sustainability. While machine learning (ML) models have improved predictive accuracy, their limited transparency has hindered their widespread adoption in materials engineering. To overcome this barrier, this study introduces a Random Forests ensemble learning model integrated with SHapley Additive exPlanations (SHAP) and Partial Dependence Plots (PDPs) to model and explain the compressive strength behavior of 3DPC mixtures. Unlike conventional “black-box” models, SHAP quantifies each variable’s contribution to predictions based on cooperative game theory, which enables causal interpretability, whereas PDP visualizes nonlinear and interactive effects between features that offer practical mix design insights. A systematically optimized random forest model achieved strong generalization (R2 = 0.978 for training, 0.834 for validation, and 0.868 for testing). The analysis identified curing age, Portland cement, silica fume, and the water-to-binder ratio as dominant predictors, with curing age exerting the highest positive influence on strength development. The integrated SHAP-PDP framework revealed synergistic interactions among binder constituents and curing parameters, which established transparent, data-driven guidelines for performance optimization. Theoretically, the study advances explainable artificial intelligence in cementitious material science by linking microstructural mechanisms to model-based reasoning, thereby enhancing both the interpretability and applicability of ML-driven mix design for next-generation 3DPC systems.
- 1 January 2025
- Published by Tech Science Press in Computer Modeling in Engineering & Sciences
- Vol. 145 (2) , 1789-1819
Open AccessExplainable Data-Driven Modeling for Optimized Mix Design of 3D-Printed Concrete: Interpreting Nonlinear Synergies among Binder Components and Proportions
The rapid advancement of three-dimensional printed concrete (3DPC) requires intelligent and interpretable frameworks to optimize mixture design for strength, printability, and sustainability. While machine learning (ML) models have improved predictive accuracy, their limited transparency has hindered their widespread adoption in materials engineering. To overcome this barrier, this study introduces a Random Forests ensemble learning model integrated with SHapley Additive exPlanations (SHAP) and Partial Dependence Plots (PDPs) to model and explain the compressive strength behavior of 3DPC mixtures. Unlike conventional “black-box” models, SHAP quantifies each variable’s contribution to predictions based on cooperative game theory, which enables causal interpretability, whereas PDP visualizes nonlinear and interactive effects between features that offer practical mix design insights. A systematically optimized random forest model achieved strong generalization (R2 = 0.978 for training, 0.834 for validation, and 0.868 for testing). The analysis identified curing age, Portland cement, silica fume, and the water-to-binder ratio as dominant predictors, with curing age exerting the highest positive influence on strength development. The integrated SHAP-PDP framework revealed synergistic interactions among binder constituents and curing parameters, which established transparent, data-driven guidelines for performance optimization. Theoretically, the study advances explainable artificial intelligence in cementitious material science by linking microstructural mechanisms to model-based reasoning, thereby enhancing both the interpretability and applicability of ML-driven mix design for next-generation 3DPC systems.