Ignacio Giner
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Ignacio Giner has a total of 72 co-authors. Here are the top co-authors by number of shared publications:
- Carlos Lafuente
Departamento de Química Física, Facultad de Ciencias, Universidad de Zaragoza, 50009 Zaragoza, Spain
11 shared publications - Ignacio Gascón
Instituto de Nanociencia y Materiales de Aragón (INMA), CSIC-Universidad de Zaragoza, Zaragoza, 50009, Spain
7 shared publications - Pilar Cea
Instituto de Nanociencia y Materiales de Aragón (INMA)
6 shared publications - Beatriz Giner
Facultad de Ciencias de la Salud, Universidad San Jorge, Campus Universitario, Autov. A23 km 299, 50830 Villanueva de Gállego, Zaragoza, Spain
5 shared publications Gorka Pera
5 shared publicationsGuido Grundmeier
Technical and Macromolecular Chemistry, University of Paderborn , Warburger Strasse 100, 33098 Paderborn, Germany
5 shared publications
Latest Publications
- 24 April 2017
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 50 (20) , 204002
Influence of organic surface chemistry on the nucleation of plasma deposited SiO x films
The nucleation and film growth of SiO x plasma polymer films as a function of the substrate surface chemistry are analysed by a combination of microscopic, spectroscopic and electrochemical techniques. Self-assembled organothiol monolayers (SAMs) surfaces with different terminating groups (methyl, carboxyl- and trimethoxysilane groups) on Au(111) serve as a model system. Ultra-thin SiO x films with thickness ranging from 0.4 to 1.4 nm were deposited by microwave plasma in a mixture of HMDSO and O 2 . The changes in surface, interface and thin film chemistry are characterized by PM-IRRAS. Cyclic voltammetry with ferricyanide as a redox system is used to probe the defect density of the bare SAMs and the SiO x -covered SAMs. Furthermore, the evolution of the SiO x surface morphology for increasing film thickness as function of the substrate chemical termination is investigated by AFM. A strong influence of the surface chemistry on the SiO x nucleation and film growth is observed. While the methyl and carboxyl terminated SAMs are degraded during the nucleation leading to defect rich ultrathin films, the trimethoxysilane group protects the aliphatic chain of the SAM and leads to much better barrier properties of the ultra-thin SiO x -films. A mechanistic explanation of the results is provided.
- 24 April 2017
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 50 (20) , 204002
Influence of organic surface chemistry on the nucleation of plasma deposited SiO x films
The nucleation and film growth of SiO x plasma polymer films as a function of the substrate surface chemistry are analysed by a combination of microscopic, spectroscopic and electrochemical techniques. Self-assembled organothiol monolayers (SAMs) surfaces with different terminating groups (methyl, carboxyl- and trimethoxysilane groups) on Au(111) serve as a model system. Ultra-thin SiO x films with thickness ranging from 0.4 to 1.4 nm were deposited by microwave plasma in a mixture of HMDSO and O 2 . The changes in surface, interface and thin film chemistry are characterized by PM-IRRAS. Cyclic voltammetry with ferricyanide as a redox system is used to probe the defect density of the bare SAMs and the SiO x -covered SAMs. Furthermore, the evolution of the SiO x surface morphology for increasing film thickness as function of the substrate chemical termination is investigated by AFM. A strong influence of the surface chemistry on the SiO x nucleation and film growth is observed. While the methyl and carboxyl terminated SAMs are degraded during the nucleation leading to defect rich ultrathin films, the trimethoxysilane group protects the aliphatic chain of the SAM and leads to much better barrier properties of the ultra-thin SiO x -films. A mechanistic explanation of the results is provided.
- 1 December 2016
- Published by Elsevier in Applied Surface Science
- Vol. 389, 144-156
Influence of stripping and cooling atmospheres on surface properties and corrosion of zinc galvanizing coatings
- 1 December 2016
- Published by Elsevier in Applied Surface Science
- Vol. 389, 144-156
Influence of stripping and cooling atmospheres on surface properties and corrosion of zinc galvanizing coatings
- 7 July 2016
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 8 (28) , 17805-17816
Plasma-Enhanced Chemical Vapor Deposition (PE-CVD) yields better Hydrolytical Stability of Biocompatible SiOx Thin Films on Implant Alumina Ceramics compared to Rapid Thermal Evaporation Physical Vapor Deposition (PVD)
Densely sintered aluminum oxide (α-Al2O3) is chemically and biologically inert. To improve the interaction with biomolecules and cells, its surface has to be modified prior to use in biomedical applications. In this study, we compared two deposition techniques for adhesion promoting SiOx films to facilitate the coupling of stable organosilane monolayers on monolithic α-alumina; physical vapor deposition (PVD) by thermal evaporation and plasma enhanced chemical vapor deposition (PE-CVD). We also investigated the influence of etching on the formation of silanol surface groups using hydrogen peroxide and sulfuric acid solutions. The film characteristics, that is, surface morphology and surface chemistry, as well as the film stability and its adhesion properties under accelerated aging conditions were characterized by means of X-ray photoelectron spectroscopy (XPS), energy dispersive X-ray spectroscopy (EDX), scanning electron microscopy (SEM), inductively coupled plasma–optical emission spectroscopy (ICP-OES), and tensile strength tests. Differences in surface functionalization were investigated via two model organosilanes as well as the cell-cytotoxicity and viability on murine fibroblasts and human mesenchymal stromal cells (hMSC). We found that both SiOx interfaces did not affect the cell viability of both cell types. No significant differences between both films with regard to their interfacial tensile strength were detected, although failure mode analyses revealed a higher interfacial stability of the PE-CVD films compared to the PVD films. Twenty-eight day exposure to simulated body fluid (SBF) at 37 °C revealed a partial delamination of the thermally deposited PVD films whereas the PE-CVD films stayed largely intact. SiOx layers deposited by both PVD and PE-CVD may thus serve as viable adhesion-promoters for subsequent organosilane coupling agent binding to α-alumina. However, PE-CVD appears to be favorable for long-term direct film exposure to aqueous solutions.
- 7 July 2016
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 8 (28) , 17805-17816
Plasma-Enhanced Chemical Vapor Deposition (PE-CVD) yields better Hydrolytical Stability of Biocompatible SiOx Thin Films on Implant Alumina Ceramics compared to Rapid Thermal Evaporation Physical Vapor Deposition (PVD)
Densely sintered aluminum oxide (α-Al2O3) is chemically and biologically inert. To improve the interaction with biomolecules and cells, its surface has to be modified prior to use in biomedical applications. In this study, we compared two deposition techniques for adhesion promoting SiOx films to facilitate the coupling of stable organosilane monolayers on monolithic α-alumina; physical vapor deposition (PVD) by thermal evaporation and plasma enhanced chemical vapor deposition (PE-CVD). We also investigated the influence of etching on the formation of silanol surface groups using hydrogen peroxide and sulfuric acid solutions. The film characteristics, that is, surface morphology and surface chemistry, as well as the film stability and its adhesion properties under accelerated aging conditions were characterized by means of X-ray photoelectron spectroscopy (XPS), energy dispersive X-ray spectroscopy (EDX), scanning electron microscopy (SEM), inductively coupled plasma–optical emission spectroscopy (ICP-OES), and tensile strength tests. Differences in surface functionalization were investigated via two model organosilanes as well as the cell-cytotoxicity and viability on murine fibroblasts and human mesenchymal stromal cells (hMSC). We found that both SiOx interfaces did not affect the cell viability of both cell types. No significant differences between both films with regard to their interfacial tensile strength were detected, although failure mode analyses revealed a higher interfacial stability of the PE-CVD films compared to the PVD films. Twenty-eight day exposure to simulated body fluid (SBF) at 37 °C revealed a partial delamination of the thermally deposited PVD films whereas the PE-CVD films stayed largely intact. SiOx layers deposited by both PVD and PE-CVD may thus serve as viable adhesion-promoters for subsequent organosilane coupling agent binding to α-alumina. However, PE-CVD appears to be favorable for long-term direct film exposure to aqueous solutions.
- 17 June 2016
- Published by Wiley in Surface and Interface Analysis
- Vol. 49 (1) , 71-74
In situ PM‐IRRAS studies of organothiols and organosilane monolayers–ZnO interfaces at high water activities
In situ photoelastic‐modulated Fourier transform infrared reflection absorption spectroscopy has been applied for the investigation of interfacial stability of organothiol and organosilane monolayer films on nanocrystalline zinc oxide thin films. It has been shown that for octadecyltriethoxysilane films, exposure to high water activities results in physisorption of water in the cross‐linked film. This high water activity at the interface leads to a reversible wet de‐adhesion of the interfacial silanol groups from the ZnO surface. However, the organothiol seems to form a denser monolayer and a stable by S–Zn bond that is resistant to the competition with adsorbed water. The reversible attachment for cross‐linked organosilanol films has been demonstrated for the first time by means of an in situ spectroscopic method on model ZnO surfaces. Copyright © 2016 John Wiley & Sons, Ltd.
- 17 June 2016
- Published by Wiley in Surface and Interface Analysis
- Vol. 49 (1) , 71-74
In situ PM‐IRRAS studies of organothiols and organosilane monolayers–ZnO interfaces at high water activities
In situ photoelastic‐modulated Fourier transform infrared reflection absorption spectroscopy has been applied for the investigation of interfacial stability of organothiol and organosilane monolayer films on nanocrystalline zinc oxide thin films. It has been shown that for octadecyltriethoxysilane films, exposure to high water activities results in physisorption of water in the cross‐linked film. This high water activity at the interface leads to a reversible wet de‐adhesion of the interfacial silanol groups from the ZnO surface. However, the organothiol seems to form a denser monolayer and a stable by S–Zn bond that is resistant to the competition with adsorbed water. The reversible attachment for cross‐linked organosilanol films has been demonstrated for the first time by means of an in situ spectroscopic method on model ZnO surfaces. Copyright © 2016 John Wiley & Sons, Ltd.
- Open Access
- 11 January 2016
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 4 (5) , 1057-1065
An efficient PE-ALD process for TiO2 thin films employing a new Ti-precursor
An efficient plasma-enhanced atomic layer deposition (PE-ALD) process was developed for TiO2 thin films of high quality, using a new Ti-precursor, namely tris(dimethylamido)-(dimethylamino-2-propanolato)titanium(IV) (TDMADT). The five-coordinated titanium complex is volatile, thermally stable and reactive, making it a potential precursor for ALD and PE-ALD processes. Process optimization was performed with respect to plasma pulse length and reactive gas flow rate. Besides an ALD window, the application of the new compound was investigated using in situ quartz-crystal microbalance (QCM) to monitor surface saturation and growth per cycle (GPC). The new PE-ALD process is demonstrated to be an efficient procedure to deposit stoichiometric titanium dioxide thin films under optimized process conditions with deposition temperatures as low as 60 °C. Thin films deposited on Si(100) and polyethylene-terephthalate (PET) exhibit a low RMS roughness of about 0.22 nm. In addition, proof-of-principle studies on TiO2 thin films deposited on PET show promising results in terms of barrier performance with oxygen transmission rates (OTR) found to be as low as 0.12 cm3 × cm−2 × day−1 for 14 nm thin films.
- 11 January 2016
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 4 (5) , 1057-1065
Open AccessAn efficient PE-ALD process for TiO2 thin films employing a new Ti-precursor
An efficient plasma-enhanced atomic layer deposition (PE-ALD) process was developed for TiO2 thin films of high quality, using a new Ti-precursor, namely tris(dimethylamido)-(dimethylamino-2-propanolato)titanium(IV) (TDMADT). The five-coordinated titanium complex is volatile, thermally stable and reactive, making it a potential precursor for ALD and PE-ALD processes. Process optimization was performed with respect to plasma pulse length and reactive gas flow rate. Besides an ALD window, the application of the new compound was investigated using in situ quartz-crystal microbalance (QCM) to monitor surface saturation and growth per cycle (GPC). The new PE-ALD process is demonstrated to be an efficient procedure to deposit stoichiometric titanium dioxide thin films under optimized process conditions with deposition temperatures as low as 60 °C. Thin films deposited on Si(100) and polyethylene-terephthalate (PET) exhibit a low RMS roughness of about 0.22 nm. In addition, proof-of-principle studies on TiO2 thin films deposited on PET show promising results in terms of barrier performance with oxygen transmission rates (OTR) found to be as low as 0.12 cm3 × cm−2 × day−1 for 14 nm thin films.
- 1 November 2015
- Published by Elsevier in Corrosion Science
- Vol. 100, 496-503
Fundamental understanding of the corrosion and biomineralization of MgO surfaces – An in situ AFM study
- 1 November 2015
- Published by Elsevier in Corrosion Science
- Vol. 100, 496-503
Fundamental understanding of the corrosion and biomineralization of MgO surfaces – An in situ AFM study
- 20 July 2015
- Published by Wiley in Plasma Processes and Polymers
- Vol. 12 (9) , 1002-1009
Spectroscopic and Microscopic Investigations of Degradation Processes in Polymer Surface‐Near Regions During the Deposition of SiOx Films
- 20 July 2015
- Published by Wiley in Plasma Processes and Polymers
- Vol. 12 (9) , 1002-1009
Spectroscopic and Microscopic Investigations of Degradation Processes in Polymer Surface‐Near Regions During the Deposition of SiOx Films
- 1 October 2014
- Published by Elsevier in Corrosion Science
- Vol. 87, 51-59
In situ AFM studies of the stability of MgO(1 0 0) in aqueous electrolytes
- 1 October 2014
- Published by Elsevier in Corrosion Science
- Vol. 87, 51-59
In situ AFM studies of the stability of MgO(1 0 0) in aqueous electrolytes
- Open Access
- 1 April 2014
- Published by Elsevier in Thin Solid Films
- Vol. 556, 485-494
Characterization of Langmuir and Langmuir–Blodgett films of an octasubstituted zinc phthalocyanine
- 1 April 2014
- Published by Elsevier in Thin Solid Films
- Vol. 556, 485-494
Open AccessCharacterization of Langmuir and Langmuir–Blodgett films of an octasubstituted zinc phthalocyanine
- 1 March 2014
- Published by Elsevier in Chemical Physics Letters
- Vol. 597, 134-138
Influence of the surface chemistry on TiO2 – TiO2 nanocontact forces as measured by an UHV–AFM
- 1 March 2014
- Published by Elsevier in Chemical Physics Letters
- Vol. 597, 134-138
Influence of the surface chemistry on TiO2 – TiO2 nanocontact forces as measured by an UHV–AFM