Christopher V. Young

The achievement of fusion ignition at the National Ignition Facility opens new opportunities for foundational studies in opacity, radiation transport, and high-flux astrophysics in regimes previously unattainable. We have succeeded in the critical enabling step of demonstrating ignition in a hohlraum modified with diagnostic windows that burn through prior to ignition, granting experimental access to the brightest radiation source in the laboratory. This Letter reports the results of a deuterium-tritium-layered capsule implosion that achieved 2.4 ± 0.09 MJ neutron yield in a hohlraum with windows designed to allow the escape of radiation energy from the capsule without significant loss of implosion symmetry, thus establishing a validated platform for next-generation radiation-driven experiments.

A critical aspect of inertial confinement fusion experiments lies in the control of ablation front instabilities during the implosion process. The growth of Rayleigh–Taylor and Richtmyer–Meshkov instabilities, seeded by target defects, can significantly degrade the performance of the implosion. This study explores the influence of drive design on ablation front stability using the hydro-growth radiography platform at the National Ignition Facility. This platform allows the measurement of the ablation front hydrodynamic instability growth. Because these measurements are restricted to early convergence, their primary role is to constrain the initial instability growth and benchmark the simulations used to infer shell integrity and performance at peak velocity and ignition. Three ignition designs, Hybrid-E (HyE), SQ-n (“S” for scaling and “Q” for quality), and High temperature, High thickness (HiT) were analyzed. The results demonstrated a high dependence of the growth factor on the choice of design, capsule scale as well as the hohlraum conditions, mainly the radiative temperature and the gold M-band emission. HyE and SQ-n display a similar growth factor range, but their evolution is different due to the design differences in hohlraum conditions. HiT has the lowest growth factor of the studied designs, which is a result of a higher radiative temperature. These results highlight the importance of design choices in controlling instability dynamics. These insights inform future drive design strategies to enhance stability and efficiency in fusion ignition experiments.

Successful demonstration of an implosion that meets the physics metrics for ignition on the National Ignition Facility (NIF) in August 2021 and demonstration of target energy gain G > 1 in December 2022 represented the culmination of more than a decade of research on the NIF. An in-depth analysis of the key ignition metrics achieved on the NIF over the past decade shows sustained progress toward identifying and mitigating degradation effects. Ignition implosions on the NIF have progressed from early experiments whose compressed fuel conditions were degraded by a factor of 10–20 below the ignition threshold with yields of only 1%–2% of the laser energy, to current experiments that significantly exceed the ignition threshold and in the best experiments achieve yields greater than twice the laser energy. It is very likely that NIF can get more than 20 MJ of yield and possibly 50–70 MJ yields when fully optimized at an ultraviolet laser energy of 2.6 MJ following the completion of the NIF Extended Yield Capability Project. Achieving these higher yields will also require improvements to capsules at larger size and possibly with alternate materials, as well as an improved understanding of hohlraum and capsule physics. Now that NIF has achieved ignition, the design of a Next Generation High Energy Density Facility that could achieve the National Nuclear Security Administration long-term goal of substantially higher yields than the NIF can proceed with a more confident physics base. We evaluate these opportunities including possible applications for inertial fusion energy and likely challenges to achieving this level of performance over the next decade.

We conduct capsule surrogate experiments at the National Ignition Facility to calibrate radiation hydrodynamic simulations to infer hydrodynamic conditions that are not observable in indirect drive ignition implosions. We tune the simulations by applying laser power and cross beam energy transfer (CBET) saturation multipliers to match the observables from capsule surrogate experiments. Shock timing, velocity, and symmetry are measured in liquid D2 filled Keyhole capsule surrogate experiments and implosion trajectory, stagnation time, and shape time history are measured in in-flight 2D backlit x-ray radiography experiments (“2DConA”) of D2 gas filled capsule implosions. Calibrated simulations suggest that the N210808 ignition implosion (fusion target gain = 0.7) had a shell mass remaining at stagnation of less than the nominal %5 (3.8%) and resulted in less confinement. For N221204, the shell was made 5.75 μm thicker to trade implosion velocity for increased confinement and resulted in a target gain = 1.5 with a shell mass remaining of 5.7%. Furthermore, a single adjusted model can reproduce all shock timing data as changes are made to shell thickness (79–85 μm) and laser wavelength separation (1.8–4.0 Å). However, for the 2DConA implosions, a 5% variation in the peak power laser multipliers and a 30% variation in late-time CBET between experiments are needed to match the observed stagnation times, in-flight P2 shape, and hot-spot P2 shape. While progress is being made to improve the models in simulations using focused experiments, capsule surrogate experiments will continue to be needed to optimize future ignition designs.

Laser-driven, indirect-drive inertial confinement fusion (ICF) experiments at the National Ignition Facility (NIF) recently achieved a target gain greater than one, where fusion energy output exceeds input laser energy [Abu-Shawareb et al., Phys. Rev. Lett. 132, 065102 (2024)]. Despite this milestone, gain levels remain insufficient for practical applications such as inertial fusion energy, making performance improvement critical. One promising approach is increasing fuel compression by lowering the implosion adiabat. To explore reduced adiabat, experiments were conducted modifying the laser pulse shape and shock timing of an existing 1.9-MJ-drive implosion design performing near the ignition cliff [Abu-Shawareb et al., Phys. Rev. Lett. 129, 075001 (2022)]. These experiments demonstrated increased compression and fusion yield in ICF implosions at the NIF by using a lower fuel adiabat, and increased compression with a reduced adiabat in high-density carbon ablators. The updated design achieved up to 80% higher fusion yield and 14% greater fuel compression compared to the previous best-performing 1.9-MJ experiment, with repeatable performance, and is the only implosion design to achieve a target gain exceeding one with < 2.04 MJ laser energy. Notably, this work was made possible because of recent advances in target quality and pulse shape control allowing experimental access to the ignition regime, and thereby increased sensitivity to adiabat. This work addresses a long-standing question in ICF research and lays the foundation for higher target gains through optimized implosion strategies. It underscores the potential of reduced adiabat designs to enhance compression and fusion yields for future ICF applications.

Mixing of the ablator material into the fuel of an inertial confinement fusion implosion reduces compression and enhances radiative losses, preventing ignition. We describe a novel use of charged-particle radiochemistry to measure the ablator mix in contact with the fusion hot spot. The capsule uses a graded Be-Cr layer to increase the confinement of the hot spot. ^{52}Mn and ^{51}Cr isotopes are collected from the implosion and counted, and the ratio is related to the amount of Cr mixed into the hot spot. Thus, a new diagnostic to determine the degradation due to mix on fusion implosions has been developed.

Recent advancements in indirect-drive inertial confinement fusion (ICF) experiments at the National Ignition Facility (NIF) have achieved a significant milestone by demonstrating target gains greater than one, yet future applications necessitate much higher target gains. One approach to achieving improved implosion performance is to pursue increased fuel compression via a lowered implosion adiabat. Experiments have been performed testing a reduced adiabat by introducing small changes to the drive laser pulse shape and the resulting shock timing for an existing implosion design at 1.9 MJ laser drive with near-ignition performance (experiment N210808). Experiments using the updated design demonstrate, for the very first time, increased compression and fusion yield in ICF implosions on the NIF by using a lower fuel adiabat, and increased compression with a reduced adiabat in high-density carbon ablators. Compared to the previously best-performing experiment with a laser energy of 1.9 MJ, these experiments exhibit increases of up to 80% and 14% in nuclear fusion yield and fuel compression, respectively, and with repeatable performance. Further, it is the only implosion design to have achieved a target gain exceeding one with a laser energy of less than 2 MJ. These findings highlight the efficacy of reduced adiabat designs in achieving higher compression and fusion yields, offering a promising pathway for future ICF applications. This Letter not only addresses a long-standing question in ICF but also paves the way for achieving higher target gains with optimized implosion strategies.

For many decades, the running joke in fusion research has been that ‘fusion’ is thirty years away and always will be. Yet, these past few years we find ourselves in a position where we can now talk about the milestones of burning plasmas, fusion ignition, and target energy gain greater than unity (scientific breakeven) in the past tense. Fusion is no longer a joke! Yet getting to fusion ignition, the tipping-point of thermonuclear instability resulting in an explosive increase in ion thermal temperature and fusion reaction-rate, and scientific breakeven (target gain, G target = fusion yield/deposited laser energy > 1 , in the laser-driven inertial confinement fusion context) has not been easy. In this publication we discuss our present understanding of the physics and technological challenges surrounding ignition and Gain as well as highlight some outstanding problems that still need resolution.

We describe our current understanding of the variability and degradation mechanisms observed through a series of five indirectly driven inertial fusion implosions fielded at the National Ignition Facility in the fall of 2021, four of which attempted to reproduce the first experiment to achieve Lawson's criterion for ignition with a thermonuclear yield of 1.35 MJ on August 8, 2021. A large number of absolutely calibrated (imaging, time-resolved, and spectrally resolved) x-ray and neutron diagnostics are fielded on the NIF along multiple lines of sight for each experiment. This allows for a reconstruction of the DT fuel and ablator mix injected into the hotspot around peak burn. We show that nuclear yield variations are well reproduced by numerical modeling when the measured low mode asymmetries and mix mass are included. Furthermore, these observed perturbations during burn are linked to small variations in laser delivery and capsule defects. Stringent specifications are then set to achieve robust ignition with the implosion design studied in this paper.

A decades-long quest to achieve fusion energy target gain and ignition in a controlled laboratory experiment, dating back to 1962, has been realized at the National Ignition Facility (NIF) on December 5, 2022 [Abu-Shawareb et al., Phys. Rev. Lett. 132, 065102 (2024)] where an imploded pellet of deuterium and tritium (DT) fuel generated more fusion energy (3.15 MJ) than laser energy incident on the target (2.05 MJ). In these experiments, laser beams incident on the inside of a cylindrical can (Hohlraum) generate an intense ∼3 × 106 million degree x-ray radiation bath that is used to spherically implode ∼2 mm diameter pellets containing frozen deuterium and tritium. The maximum fusion energy produced in this configuration to date is 3.88 MJ using 2.05 MJ of incident laser energy and 5.2 MJ using 2.2 MJ of incident laser energy, producing a new record target gain of ∼2.4×. This paper describes the physics (target and laser) design of this platform and follow-on experiments that show increased performance. We show robust megajoule fusion energy output using this design as well as explore design modification using radiation hydrodynamic simulations benchmarked against experimental data, which can further improve the performance of this platform.