Snežana Mašović
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Snežana Mašović has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Nenad Pecić
Faculty of Civil Engineering University of Belgrade Belgrade Serbia
2 shared publications- Nenad Pecić
University of Belgrade, Faculty of Civil Engineering, Bulevar kralja Aleksandra 73, 11000 Belgrade, Serbia
2 shared publications Saša Stošić
Faculty of Civil Engineering University of Belgrade Belgrade Serbia
2 shared publications- Saša Stošić
University of Belgrade, Faculty of Civil Engineering, Bulevar kralja Aleksandra 73, 11000 Belgrade, Serbia
2 shared publications Dragan Mašović
V.prof. dr Snežana Mašović
1 shared publication- Nikola Tanasić
Infrastructure Management Consultants GmbH Mannheim, Germany
1 shared publication
Latest Publications
- Open Access
- 1 January 2023
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Gradjevinski kalendar
- Vol. 55 (1) , 90-111
Shear design of reinforced concrete elements with circular cross section according to Eurocode 2
Eurocode 2 does not provide explicit guidance for the shear design of elements with circular cross-section - the terms in the provisions are intended for elements with concentrated tensile reinforcement, such as beams subjected to bending. The most common elements with circular cross-section are columns and piles, which typically have uniformly distributed reinforcement around the circumference and significant axial force. It is necessary to adjust the relevant inputs in order to formulate procedures of reasonable complexity, which are suitable for practical application. The paper presents the application of the Eurocode's 2 model for shear design on circular cross-section elements. Simple instructions are given for practical calculations that are on the safe side, covering all aspects of shear design: shear resistance of concrete, shear resistance of reinforcement, maximum shear resistance and calculation of additional tensile reinforcement. The procedures are illustrated with a numerical example in accordance with the national document SRPS EN 1992-1-1/NA.
- 1 January 2023
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Gradjevinski kalendar
- Vol. 55 (1) , 90-111
Open AccessShear design of reinforced concrete elements with circular cross section according to Eurocode 2
Eurocode 2 does not provide explicit guidance for the shear design of elements with circular cross-section - the terms in the provisions are intended for elements with concentrated tensile reinforcement, such as beams subjected to bending. The most common elements with circular cross-section are columns and piles, which typically have uniformly distributed reinforcement around the circumference and significant axial force. It is necessary to adjust the relevant inputs in order to formulate procedures of reasonable complexity, which are suitable for practical application. The paper presents the application of the Eurocode's 2 model for shear design on circular cross-section elements. Simple instructions are given for practical calculations that are on the safe side, covering all aspects of shear design: shear resistance of concrete, shear resistance of reinforcement, maximum shear resistance and calculation of additional tensile reinforcement. The procedures are illustrated with a numerical example in accordance with the national document SRPS EN 1992-1-1/NA.
- Open Access
- 1 January 2023
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Građevinski materijali i konstrukcije
- Vol. 66 (2) , 115-125
Risk management in civil engineering
Risk is involved in the whole lifecycle of a structure: design, construction, utilization, and demolition. There is a close connection between reliability and risk. Contemporary building codes introduce consideration of reliability in structural design. Here, the concept of risk takes into account the level of consequences of a failure. Structural engineers, who are used to deterministic calculation procedures, are often unfamiliar with the uncertainties associated with risk analysis. An overview of the basic principles of risk management in civil engineering is presented in this paper.
- 1 January 2023
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in Građevinski materijali i konstrukcije
- Vol. 66 (2) , 115-125
Open AccessRisk management in civil engineering
Risk is involved in the whole lifecycle of a structure: design, construction, utilization, and demolition. There is a close connection between reliability and risk. Contemporary building codes introduce consideration of reliability in structural design. Here, the concept of risk takes into account the level of consequences of a failure. Structural engineers, who are used to deterministic calculation procedures, are often unfamiliar with the uncertainties associated with risk analysis. An overview of the basic principles of risk management in civil engineering is presented in this paper.
- 21 June 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (2) , 2547-2562
Span‐to‐depth ratio limits for deflection control of reinforced concrete elements
Indirect deflection control usually applies the limitation of the span‐to‐depth ratio. The procedures that have developed in the past decades have mostly been derived for predefined values of some of the relevant parameters. Assigning values to parameters simplifies the application of criteria. Predefined values may not be suitable for all design situations and some of the recently published procedures allow direct selection of relevant parameters. This paper offers new expressions for span‐to‐depth ratio limits for deflection control. Expressions include cross‐section size, area, and position of tensile and compressive reinforcement, mechanical and long‐term properties of concrete and deflection limit. The load level is represented by the stress in the tensile reinforcement so that the ratio of live and total load can be arbitrary. The dimensionless form of deflection calculation by numerical integration of the mean curvature according to Eurocode 2 is used to formulate the expressions. The proposed procedure is verified with a large number of numerical simulations for different combinations of inputs. Measured long‐term deflections, available from the literature, are also used to test the procedure. The expressions are suitable for both deflection control and conceptual design.
- 21 June 2022
- Published by Wiley in Structural Concrete
- Vol. 24 (2) , 2547-2562
Span‐to‐depth ratio limits for deflection control of reinforced concrete elements
Indirect deflection control usually applies the limitation of the span‐to‐depth ratio. The procedures that have developed in the past decades have mostly been derived for predefined values of some of the relevant parameters. Assigning values to parameters simplifies the application of criteria. Predefined values may not be suitable for all design situations and some of the recently published procedures allow direct selection of relevant parameters. This paper offers new expressions for span‐to‐depth ratio limits for deflection control. Expressions include cross‐section size, area, and position of tensile and compressive reinforcement, mechanical and long‐term properties of concrete and deflection limit. The load level is represented by the stress in the tensile reinforcement so that the ratio of live and total load can be arbitrary. The dimensionless form of deflection calculation by numerical integration of the mean curvature according to Eurocode 2 is used to formulate the expressions. The proposed procedure is verified with a large number of numerical simulations for different combinations of inputs. Measured long‐term deflections, available from the literature, are also used to test the procedure. The expressions are suitable for both deflection control and conceptual design.
- 29 June 2017
- Published by Wiley in Structural Concrete
- Vol. 18 (6) , 839-849
Verification of deflection according to Eurocode 2
Code provisions for a simplified check of the long‐term deflection of concrete structures are generally developed for predefined values of the relevant input parameters. Deflection calculation may be of interest to account for different design situations. EN 1992‐1‐1 advocates the integration of curvatures calculated using the effective modulus of concrete. This paper presents an efficient procedure for calculation of the long‐term deflection due to a sustained load. A nondimensional analysis of the mean curvature is applied to evaluate the deflection. The deflection is calculated using a set of algebraic expressions. The result is close to the value obtained by the numerical integration of curvatures. The values of relevant parameters in the expressions may be selected within the common range for the design of engineering structures. The efficiency of the deflection prediction based on the integration of curvatures is tested on the available experimental data. In the first approach, the measured material properties are used. In the second approach, the required values are derived from EN 1992‐1‐1 expressions to predict the material properties.
- 29 June 2017
- Published by Wiley in Structural Concrete
- Vol. 18 (6) , 839-849
Verification of deflection according to Eurocode 2
Code provisions for a simplified check of the long‐term deflection of concrete structures are generally developed for predefined values of the relevant input parameters. Deflection calculation may be of interest to account for different design situations. EN 1992‐1‐1 advocates the integration of curvatures calculated using the effective modulus of concrete. This paper presents an efficient procedure for calculation of the long‐term deflection due to a sustained load. A nondimensional analysis of the mean curvature is applied to evaluate the deflection. The deflection is calculated using a set of algebraic expressions. The result is close to the value obtained by the numerical integration of curvatures. The values of relevant parameters in the expressions may be selected within the common range for the design of engineering structures. The efficiency of the deflection prediction based on the integration of curvatures is tested on the available experimental data. In the first approach, the measured material properties are used. In the second approach, the required values are derived from EN 1992‐1‐1 expressions to predict the material properties.