MMMatthieu Michiels

Matthieu Michiels

*This is an algorithmically generated author record based on publicly available information.

Matthieu Michiels has a total of 23 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Insights on film growth conditions on a floating substrate during reactive Ar/O2 bipolar high power impulse magnetron sputter deposition

    by M Michiels, N Britun, A Caillard, A-L Thomann, R Snyders, S Konstantinidis

    We report several effects found in reactive bipolar high-power impulse magnetron sputtering (abbreviated as bipolar HiPIMS or BPH) discharges at the substrate level. The role of the negative peak current and the positive pulse voltage, U + , on the deposition flux at the electrically insulating substrate is discussed and the results are compared to conventional DC discharges. In particular, the normalized energy flux, ϕ n , delivered to the substrate is found higher under BPH conditions at U + = +300 V ( φ n = 3.43 × 10 15 eV·nm−3) as compared to the HiPIMS ( φ n = 0.78 × 10 15 eV·nm−3) and DCMS ( φ n = 1.23 × 10 15 eV·nm−3) regimes which is assumed to be provoked by an intensification of the positive ion bombardment. Accordingly, the mean energy and the count of positively charged metal and gaseous ions increase in line with U + as measured by energy-resolved mass spectrometry. Contrariwise, our analysis has shown a significant decrease (≈20 %) of negative oxygen ion count under BPH conditions.


  • Magnetic field topology for altering ion density in bipolar sputtering

    by M. Michiels, K. Leonova, T. Godfroid, R. Snyders, N. Britun

    A drastic change in the spatial ion distribution in bipolar magnetron sputtering discharge is reported upon changing the magnetic field topology. In our case, a significant increase in ion number density at certain time delays is registered when topology is changed toward the unbalanced type. A transitory torch-shaped ionization zone consequently disappears, along with the low-energy part of the ion energy distribution, due to no additional ionization in this case.


  • On the relationship between the plasma characteristics, the microstructure and the optical properties of reactively sputtered TiO2 thin films

    by M Michiels, A Hemberg, T Godfroid, O Douheret, J L Colaux, P Moskovkin, S Lucas, A Caillard, A-L Thomann, P Laha, et al.

    A titanium target was reactively sputtered in an Ar/O 2 atmosphere by (i) conventional direct current magnetron sputtering (DCMS), (ii) high-power impulse magnetron sputtering (HiPIMS), and (iii) bipolar HiPIMS (BPH) discharges for the deposition of titanium dioxide thin films without intentional heating and biasing. In the HiPIMS and BPH cases, the peak current density was set to either 0.32 A cm −2 or 0.86 A cm −2 . The time-averaged power density delivered to the plasma was set to ≈1.2 W cm −2 in each case. For the BPH discharge, a positive pulse of +300 V was applied after the negative pulse to accelerate the positive ions toward the substrate. Energy-resolved mass spectrometry analysis has shown a low-energy peak for DCMS while a high energy tail extending in the range of several tens of eV was observed with HiPIMS. In the BPH discharge, the energy reached ≈300 eV for Ti + ions, which is in agreement with the applied positive potential. According to the x-ray diffraction patterns, amorphous coatings were obtained with DCMS, while rutile TiO 2 was obtained with both HiPIMS and BPH. However, in the BPH case, diffractograms were characterized by more intense high-angle diffraction peaks highlighting a modification of the growth process for these conditions. Rutherford backscattering spectrometry analysis has shown that a higher amount of argon atoms were incorporated into the TiO 2 films which are found to be slightly understoichiometric for the BPH discharge. It was also found that the refractive index, n, varied as a function of the sputtering regime with the highest value obtained in the HiPIMS case ( n = 2.73 at 550 nm). Finally, the experimentally determined optical data were compared to the ones extracted from NASCAM simulations which are found in good agreement except for the BPH case.


  • A poly-diagnostic study of bipolar high-power magnetron sputtering: role of electrical parameters

    by Matthieu Michiels, Thomas Godfroid, Rony Snyders, Nikolay Britun

    Ion acceleration in a bipolar high-power impulse magnetron sputtering discharge working with Ar gas and using a Ti cathode has been investigated. The multiple discharge diagnostic approaches have been implemented, including the target and substrate current probe measurements, mass spectrometry and laser-induced fluorescence. In particular, the current waveforms were analysed in detail, showing the particularities of the current evolution during the negative (plasma) and positive voltage pulses. It is shown that the substrate current during the positive voltage pulse reveals two peaks, corresponding, as suggested, to two groups of the positive ions repulsed from the cathode by the applied positive potential. These observations correlate well with the mass spectrometry measurements as well as with the two-dimensional ion density mapping performed for several discharge conditions by laser-induced fluorescence imaging technique.


  • Ion density evolution in a high-power sputtering discharge with bipolar pulsing

    by N. Britun, M. Michiels, T. Godfroid, R. Snyders

    Time evolution of sputtered metal ions in high power impulse magnetron sputtering (HiPIMS) discharge with a positive voltage pulse applied after a negative one (regime called “bipolar pulse HiPIMS”—BPH) is studied using 2-D density mapping. It is demonstrated that the ion propagation dynamics is mainly affected by the amplitude and duration of the positive pulse. Such effects as ion repulsion from the cathode and the ionization zone shrinkage due to electron drift towards the cathode are clearly observed during the positive pulse. The BPH mode also alters the film crystallographic structure, as observed from X-ray diffraction analysis.


  • Towards higher stability of resonant absorption measurements in pulsed plasmas

    by Nikolay Britun, Matthieu Michiels, Rony Snyders

    Possible ways to increase the reliability of time-resolved particle density measurements in pulsed gaseous discharges using resonant absorption spectroscopy are proposed. A special synchronization, called “dynamic source triggering,” between a gated detector and two pulsed discharges, one representing the discharge of interest and another being used as a reference source, is developed. An internal digital delay generator in the intensified charge coupled device camera, used at the same time as a detector, is utilized for this purpose. According to the proposed scheme, the light pulses from the reference source follow the gates of detector, passing through the discharge of interest only when necessary. This allows for the utilization of short-pulse plasmas as reference sources, which is critical for time-resolved absorption analysis of strongly emitting pulsed discharges. In addition to dynamic source triggering, the reliability of absorption measurements can be further increased using simultaneous detection of spectra relevant for absorption method, which is also demonstrated in this work. The proposed methods are illustrated by the time-resolved measurements of the metal atom density in a high-power impulse magnetron sputtering (HiPIMS) discharge, using either a hollow cathode lamp or another HiPIMS discharge as a pulsed reference source.