Raymond L. Boxman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Raymond L. Boxman has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Isak. I. Beilis
Department of Physical Electronics, School of Electrical Engineering, Faculty of Engineering, Tel Aviv University, Tel Aviv 69978, Israel
5 shared publications S Goldsmith
Electrical Discharge and Plasma Laboratory, Tel-Aviv University, POB 39040, Tel-Aviv 69978, Israel
2 shared publicationsV.N. Zhitomirsky
School of Electrical Engineering, Tel Aviv University, Tel Aviv 69978, Israel
2 shared publications- Alexey Shashurin
School of Aeronautics and Astronautics, Purdue University , 701 W Stadium Ave., West Lafayette, Indiana 47907
1 shared publication - Amnon Fruchtman
H.I.T. - Holon Institute of Technology , 52 Golomb St., Holon 58102
1 shared publication D Arbilly
Tel Aviv University
1 shared publication
Latest Publications
- 2 January 2025
- Published by Taylor & Francis in Journal of Microwave Power and Electromagnetic Energy
- Vol. 59 (1) , 3-17
Electromagnetic monitoring of the drying of in-shell Macadamia nuts
- 2 January 2025
- Published by Taylor & Francis in Journal of Microwave Power and Electromagnetic Energy
- Vol. 59 (1) , 3-17
Electromagnetic monitoring of the drying of in-shell Macadamia nuts
- 1 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 50 (9) , 2709-2713
Thin Zr Film Deposition Using a Refractory Anode Vacuum Arc Plasma Source
Thin Zr films were deposited using a vacuum arc with a refractory graphite anode and a water-cooled Zr cathode. The deposition rate was obtained from the film thickness, measured by profilometry, and time of exposure to the arc plasma. The deposition rate increased with the arc current, gap distance, and arcing time before substrate exposure to Zr plasma. The measured deposition rate reached 0.9$\mu$ m/min for an arc current of 225 A for time before substrate exposure of 90 s and the rate tends to about 1$\mu$ m/min with further this time.- 1 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 50 (9) , 2709-2713
Thin Zr Film Deposition Using a Refractory Anode Vacuum Arc Plasma Source
Thin Zr films were deposited using a vacuum arc with a refractory graphite anode and a water-cooled Zr cathode. The deposition rate was obtained from the film thickness, measured by profilometry, and time of exposure to the arc plasma. The deposition rate increased with the arc current, gap distance, and arcing time before substrate exposure to Zr plasma. The measured deposition rate reached 0.9$\mu$ m/min for an arc current of 225 A for time before substrate exposure of 90 s and the rate tends to about 1$\mu$ m/min with further this time.- 22 May 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 47 (8) , 3484-3487
Plasma Generation in a Double Anode Vacuum Arc
The hot refractory anode vacuum arc (HRAVA) plasma source was previously developed with a consumed cathode and a refractory anode to reduce the macroparticle (MP) contamination in vacuum arc deposited films. The HRAVA had open cylindrical electrodes and demonstrated that it not only reduced MP sizes and numbers but also converted MP material to plasma, and thus increased the deposition rate. This paper presents a new HRAVA configuration with a double arc between a common water-cooled Cu cathode with two active surfaces and two refractory graphite or tungsten anodes, with the aim of depositing film over a wider area. The arc current in each of the two arcs was 125 A for graphite and 150 A for tungsten. The radially expanding plasma plumes from each of the cathode-anode gaps merged, forming a wider common plasma. Cu films were deposited and over a 150 mm length parallel to the arc axis, while the corresponding length from a single-HRAVA source was only 75 mm.
- 22 May 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 47 (8) , 3484-3487
Plasma Generation in a Double Anode Vacuum Arc
The hot refractory anode vacuum arc (HRAVA) plasma source was previously developed with a consumed cathode and a refractory anode to reduce the macroparticle (MP) contamination in vacuum arc deposited films. The HRAVA had open cylindrical electrodes and demonstrated that it not only reduced MP sizes and numbers but also converted MP material to plasma, and thus increased the deposition rate. This paper presents a new HRAVA configuration with a double arc between a common water-cooled Cu cathode with two active surfaces and two refractory graphite or tungsten anodes, with the aim of depositing film over a wider area. The arc current in each of the two arcs was 125 A for graphite and 150 A for tungsten. The radially expanding plasma plumes from each of the cathode-anode gaps merged, forming a wider common plasma. Cu films were deposited and over a 150 mm length parallel to the arc axis, while the corresponding length from a single-HRAVA source was only 75 mm.
- 1 May 2018
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 123 (17) , 173302
Electric force on plasma ions and the momentum of the ion-neutrals flow
The electric force on ions in plasma and the momentum flux carried by the mixed ion-neutral flow were measured and found to be equal. The experiment was performed in a direct-current gas discharge of cylindrical geometry with applied radial electric field and axial magnetic field. The unmagnetized plasma ions, neutralized by magnetized electrons, were accelerated radially outward transferring part of the gained momentum to neutrals. Measurements were taken for various argon gas flow rates between 13 and 100 Standard Cubic Centimeter per Minute, for a discharge current of 1.9 A and a magnetic field intensity of 136 G. The plasma density, electron temperature, and plasma potential were measured at various locations along the flow. These measurements were used to determine the local electric force on the ions. The total electric force on the plasma ions was then determined by integrating radially the local electric force. In parallel, the momentum flux of the mixed ion-neutral flow was determined by measuring the force exerted by the flow on a balance force meter (BFM). The maximal plasma density was between 6 × 1010 cm−3 and 5 × 1011 cm−3, the maximal electron temperature was between 8 eV and 25 eV, and the deduced maximal electric field was between 2200 V/m and 5800 V/m. The force exerted by the mixed ion-neutral flow on the BFM agreed with the total electric force on the plasma ions. This agreement showed that it is the electric force on the plasma ions that is the source of the momentum acquired by the mixed ion-neutral flow.
- 1 May 2018
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 123 (17) , 173302
Electric force on plasma ions and the momentum of the ion-neutrals flow
The electric force on ions in plasma and the momentum flux carried by the mixed ion-neutral flow were measured and found to be equal. The experiment was performed in a direct-current gas discharge of cylindrical geometry with applied radial electric field and axial magnetic field. The unmagnetized plasma ions, neutralized by magnetized electrons, were accelerated radially outward transferring part of the gained momentum to neutrals. Measurements were taken for various argon gas flow rates between 13 and 100 Standard Cubic Centimeter per Minute, for a discharge current of 1.9 A and a magnetic field intensity of 136 G. The plasma density, electron temperature, and plasma potential were measured at various locations along the flow. These measurements were used to determine the local electric force on the ions. The total electric force on the plasma ions was then determined by integrating radially the local electric force. In parallel, the momentum flux of the mixed ion-neutral flow was determined by measuring the force exerted by the flow on a balance force meter (BFM). The maximal plasma density was between 6 × 1010 cm−3 and 5 × 1011 cm−3, the maximal electron temperature was between 8 eV and 25 eV, and the deduced maximal electric field was between 2200 V/m and 5800 V/m. The force exerted by the mixed ion-neutral flow on the BFM agreed with the total electric force on the plasma ions. This agreement showed that it is the electric force on the plasma ions that is the source of the momentum acquired by the mixed ion-neutral flow.
- 10 July 2013
- Published by Elsevier in Surface and Coatings Technology
- Vol. 232, 936-940
Sn thin film deposition using a vacuum arc plasma source with a refractory anode
- 10 July 2013
- Published by Elsevier in Surface and Coatings Technology
- Vol. 232, 936-940
Sn thin film deposition using a vacuum arc plasma source with a refractory anode
- 1 February 2010
- Published by Elsevier in Surface and Coatings Technology
- Vol. 204 (11) , 1697-1701
Cathodic arc plasma deposition of nano-multilayered Zr–O/Al–O thin films
- 1 February 2010
- Published by Elsevier in Surface and Coatings Technology
- Vol. 204 (11) , 1697-1701
Cathodic arc plasma deposition of nano-multilayered Zr–O/Al–O thin films
- 1 January 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1 (10932941) , 364-367
Measurement of ion flux as a function of background gas pressure in a Hot Refractory Anode Vacuum Arc
The fraction of the ion flux in the radially expanding plasma flux was obtained in hot refractory anode vacuum arc by measuring the ion current and the film deposition characteristics. Experiments were conducted with an arc current of 200 A, a molybdenum anode and an electrode separation of about 10 mm. It was found that the collected ion current in vacuum increased about twice from the beginning of the arc (t < 30 s) to the developed HRAVA stage (t > 50-60 s). The measured ion current in argon, nitrogen, and helium environments remained approximately constant with background gas pressure up to some critical pressure (15, 30, and 75 mTorr for argon, nitrogen and helium respectively), and then decreased with pressure eventually reaching zero. The ion fraction in total deposition flux was 0.6 in vacuum and decreased with nitrogen pressure except for the pressure range 10-100 mTorr where the local maximum about 0.8 was observed
- 1 January 2006
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1 (10932941) , 364-367
Measurement of ion flux as a function of background gas pressure in a Hot Refractory Anode Vacuum Arc
The fraction of the ion flux in the radially expanding plasma flux was obtained in hot refractory anode vacuum arc by measuring the ion current and the film deposition characteristics. Experiments were conducted with an arc current of 200 A, a molybdenum anode and an electrode separation of about 10 mm. It was found that the collected ion current in vacuum increased about twice from the beginning of the arc (t < 30 s) to the developed HRAVA stage (t > 50-60 s). The measured ion current in argon, nitrogen, and helium environments remained approximately constant with background gas pressure up to some critical pressure (15, 30, and 75 mTorr for argon, nitrogen and helium respectively), and then decreased with pressure eventually reaching zero. The ion fraction in total deposition flux was 0.6 in vacuum and decreased with nitrogen pressure except for the pressure range 10-100 mTorr where the local maximum about 0.8 was observed
- 25 April 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 480-483
Transport of a vacuum arc plasma beam through the aperture of an annular anode
- 25 April 2005
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 2, 480-483
Transport of a vacuum arc plasma beam through the aperture of an annular anode
- 4 September 2003
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 36 (18) , 2262-2268
Interaction of a vacuum arc plasma beam with an obstacle positioned normal to the plasma flow
- 4 September 2003
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 36 (18) , 2262-2268
Interaction of a vacuum arc plasma beam with an obstacle positioned normal to the plasma flow
- 7 November 1997
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 30 (21) , 2972-2978
Macroparticle distribution in a quarter-torus plasma duct of a filtered vacuum arc deposition system
- 7 November 1997
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 30 (21) , 2972-2978
Macroparticle distribution in a quarter-torus plasma duct of a filtered vacuum arc deposition system