Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Milos Srecko Nedeljkovic has a total of 49 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Image-Based Fourier Reconstruction and Analysis of Free-Surface Wave Motion in a CNC-Excited Rectangular Reservoir

    by Elsagir Almaksoudi, Miloš Nedeljković, Dejan B. Ilić, Rawasy Almaksoudi, Omar Bećiragić

    Free-surface sloshing in partially filled tanks and open reservoirs can produce spatially complex surface deformation under horizontal excitation. This study presents an image-based experimental and computational workflow for reconstructing measured free-surface profiles in a laboratory-scale rectangular reservoir mounted on a Haas VF-3/VF-3SS-family CNC machining center. The tank underwent a programmed horizontal back-and-forth motion. The retained CNC controller record shows commanded x positions spanning approximately −19.976 mm to +19.851 mm, corresponding to a programmed peak-to-peak stroke of approximately 39.8 mm. The realized forcing frequency was not independently measured; therefore, no experimental near-resonance condition is claimed. Videos were recorded approximately normal to the transparent tank wall, converted to still frames, calibrated directly in physical length units, and manually digitized with WebPlotDigitizer. A truncated spatial Fourier series was fitted independently to each measured time slice. The accompanying Python applications dynamically evaluate the experimentally fitted representation: the GUI tools animate reconstructed profiles over the recorded time sequence, while the final FourierN3 implementation builds time-dependent coefficient models, linearly interpolates coefficient histories, evaluates y(x,t), and generates a three-dimensional space–time reconstructed surface. These outputs are described as dynamic Fourier reconstructions because they remain conditioned on measured coefficient histories and do not constitute independent CFD or potential-flow predictions. The Fourier harmonics are mathematical reconstruction functions and are not identified one-to-one with physical sloshing eigenmodes. For a 0.45 m tank length, linear theory gives first-mode reference frequencies of 0.687 Hz at a 4 cm water depth and 0.763 Hz at a 5 cm water depth. The workflow is demonstrated on three selected datasets that provided sufficiently clear free-surface records for consistent frame-by-frame digitization. Using a common three-harmonic benchmark, mean RMSE values were 0.8815 cm for Case A (4 cm), 1.419 cm for Case B (5 cm), and 0.5022 cm for Case C (4 cm), corresponding to mean NRMSE values of 22.0%, 28.4%, and 12.6%, respectively. For Case C, adding a fourth harmonic reduced the mean RMSE to 0.4427 cm (11.1% of water depth), an 11.8% reduction relative to the three-harmonic fit. All RMSE and NRMSE values are reconstruction errors relative to the manually digitized coordinates, not estimates of absolute experimental measurement accuracy. The results therefore demonstrate the reconstruction workflow for the three selected records rather than establish a general water-depth effect.

  • Open Access

    The Influence of Pump-Turbine Specific Speed on Hydraulic Transient Processes

    by Zdravko Giljen, Miloš Nedeljković, Yongguang Cheng

    The main porpose of this paper is to perform and present at transient process analysis on the influence of different specific speeds (nq) of the three-model pump-turbines that may implemented at the hydropower pump storage plant (HPSP) Bajina Basta, Serbia. The intention is to analyze the operation regimes along the S-shaped characteristic curve, which creates difficulties in calculations during the load-rejection process. These problems are manifested by an unusual increase in water pressure, followed by an increase in machine vibrations, thus threatening the stability of machine operation. The subject of this research is the four-quadrant (4Q) characteristic curves, presented in the form of Suter curves (the head and momentum parameters (Wh and Wm), in dependence of angle (θ)) for different wicket gate openings, of the three pump-turbine models with different specific speeds (nq = 27, nq = 38 and nq = 50). These 4Q characteristics are used as input data for numerical code developed to calculate the simultaneous load rejection of both pump-turbines. The numerical code is based on the method of characteristics and applied to the test case at HPSP. This is especially relevant when dealing with characteristic S-shaped curves that may lead to serious instability in operation during the transient process. The calculation results show changes in the pressure, speed of rotation and discharge of the machine operation regimes, but the important findings are reflected in further application of the results to determine the parametric flow and speed (Q11 and n11) trajectories of the operating points, where the unstable behavior of a pump-turbine operating in turbine mode is presented and periodically the trajectories also pass through the reverse pump zone.


  • Open Access

    Universal Form of Radial Hydraulic Machinery Four-Quadrant Equations for Calculation of Transient Processes

    by Zdravko Giljen, Miloš Nedeljković

    Suter curves for the Wh and Wm characteristics and four-quadrant (4Q) diagrams of 11 radial pump–turbine models with different specific speeds (nq = 24.34, 24.8, 27, 28.6, 38, 41.6, 41.9, 43.83, 50, 56, and 64.04) are presented for the first time in this paper, as well as Suter curves for two pump models (nq = 25 and 41.8) previously published in the literature. All of these curves were analyzed to establish a certain universal law of behavior, depending on the specific speed. To determine such a law, a fitting procedure using regression and spline methods was carried out. This paper provides details of a research plan and structures (including data collection for four-quadrant diagrams for pump–turbine and pump models under different specific speeds nq), a procedure for re-calculating four-quadrant diagrams of the models as Suter curves for the Wh and Wm characteristics, definitions of the optimal points for pump and turbine operating modes in pump–turbine models under different specific speeds, and the development of numerical models in MATLAB to obtain a universal equation for the Wh and Wm characteristics. The scientific contribution of this paper is that it is the first to publish original mathematical curves using universal equations for the Wh and Wm characteristics of radial pumps and pump–turbines. The applicability of the equations is demonstrated by considering a pumping station in which two radial pumps were installed, for which the calculation of transient processes was performed using a numerical model developed in MATLAB by the authors. The transition process results are compared for two cases: first, when input data in the numerical model are used with the values of the Suter curves for the Wh and Wm characteristics obtained by re-calculating the four-quadrant operating characteristics (Q11, n11, M11) at a given specific speed, and second, when the values of the Suter curves for the Wh and Wm characteristics are obtained from the universal equations.


  • Open Access

    Universal Form of Radial Hydraulic Machinery 4Q Equations for Calculations of Transient Processes

    by Zdravko Giljen, Miloš Nedeljković

    The Suter curves for Wh and Wm characteristics of collected and the first time presented Four-quadrant (4Q) diagrams of 11 radial pump-turbine models with different specific speeds (nq=24.34, nq=24.8, nq=27, nq=28.6, nq=38, nq=41.6, nq=41.9, nq=43.83, nq=50, nq=56, and nq=64.04) are given in the paper, as well as the Suter curves for 2 pump models (nq=25, and nq=41.8) which were already published in the literature. These 11+2 curves were analyzed to establish a certain universal law of behavior in dependence on the specific speed. For the determination of existing laws in behavior, the fitting procedure using the Regression and Spline methods was used. The paper presents a research plan and structures that include: data collection of four-quadrant diagrams for models of pump-turbines and pumps with different specific speeds (nq), the procedure of recalculation of Four-quadrant diagrams of the models into Suter curves for Wh and Wm characteristics, the definition of the optimal point for the pump and turbine operating mode in pump-turbine models for different specific speeds, and developing numerical models in the MATLAB program to obtain the Universal Equation for the Wh and Wm characteristics. The scientific contribution of this paper is the firstly published original mathematical curve named Universal Equation for the Wh and Wm characteristics for radial pumps and pump-turbines. Application of the equation has been demonstrated at the pumping station where two radial pumps are installed. The calculation of transient processes was performed using the numerical model developed by the authors in the mathematical program MATLAB. Comparison of the transition process results has been made for the two cases - when input data in the numerical model have been firstly used with the values of Suter curves for Wh and Wm characteristics obtained by recalculation from the Four-quadrant operating characteristics (Q11, n11, M11) of model’s specific speed, and then secondly with the values of the Suter curves for Wh and Wm characteristics obtained from the Universal Equation.

  • Open Access

    Study and analysis of the cavitating and non-cavitating jets - Part two: Parameters controlling the jet action and a new formula for cavitation number calculation

    by Ezddin Hutli, Miloš S. Nedeljković, Szabolcs Czifrus

    This part of the paper presents the relation between the working conditions, nozzle geometry, nozzle diameter, and jet behavior. Experimental work has been made by impinging the submerged jets on the copper specimen as a target for a period of time. The mass loss and erosion rate at various conditions were measured, calculated and analyzed. For the visualization, a high-speed camera was used and the obtained data were processed to measure parameters which are used to characterize the clouds. Correlations among the jet dynamic power, the cavity length, erosion rate, and the pertinent experimental parameters are apparent. In addition, formulas are proposed to conveniently compare the efficiency of jetting systems based on working conditions. Based on the mathematical analyses of the obtained results a new form for cavitation number calculation is proposed.


  • Open Access

    Study and analysis of the cavitating and non-cavitating jets - Part one: Parameters controlling force, power and the jet behavior

    by Ezddin Hutli, Miloš S. Nedeljković, Szabolcs Czifrus

    This paper presents the dependency of the jet power and the cavitation intensity on the working conditions of the cavitating and non-cavitating jet flow. This dependency is indicated by the cavitation erosion process and flow structure. The effects of working conditions on the cavitation erosion were experimentally investigated. The flow visualization was done using a high-speed photography recording system. The analysis shows that the erosion rate calculation and the visualization of the jet structure can be used as tools to estimate the jet strength, the jet actions, the jet power, and the performance of the jetting system.


  • Problem-Oriented Learning Based on Use of Shared Experimental Results

    by Milan Matijević, Milos S. Nedeljković, Đorđe S. Čantrak, Novica Janković

  • Lectures in Rotodynamic Pumps—From Design and Simulations to Testing

    by Djordje S. Cantrak, Novica Z. Jankovic, Milos S. Nedeljkovic, Milan S. Matijevic, Dejan B. Ilic