Hu Sheng
Research Subjects
Hu Sheng has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Duan Xinyu
State Grid Hunan Electric Power Corporation Research Institute,Changsha,China
1 shared publicationGuofeng Liao
School of Environmental Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240, China
1 shared publication- Hao Cao
State Grid Hunan Electric Power Corporation Limited Research Institute, Changsha, 410007, China
1 shared publication - Jun Cai
School of Environmental Science and Engineering, Shanghai Jiao Tong University, Shanghai, China
1 shared publication Liu Jiaojiao
State Grid Hunan Electric Power Corporation Research Institute,Changsha,China
1 shared publicationLu Ling
State Grid Hunan Electric Power Corporation Research Institute,Changsha,China
1 shared publication
Latest Publications
- 15 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 132, 700-705
An Anti-Interference Method for Substation Boundary Noise Monitoring
For the problem that substation noise measurement is easily disturbed by external interference, a substation station boundary noise anti-interference monitoring scheme is proposed. Using the beam formation of the ring array in the modal domain for far-field directional pickup of substation noise to reduce the impact of steady-state interference on the measurement. Then the array output is converted into a single-channel signal, and the presence probability of substation noise at each time-frequency bin is estimated in real-time using an improved minimum-controlled recursive averaging algorithm, thus reducing the error caused by transient interference. The simulation results prove that the proposed method can effectively improve the accuracy of noise measurement.
- 15 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 132, 700-705
An Anti-Interference Method for Substation Boundary Noise Monitoring
For the problem that substation noise measurement is easily disturbed by external interference, a substation station boundary noise anti-interference monitoring scheme is proposed. Using the beam formation of the ring array in the modal domain for far-field directional pickup of substation noise to reduce the impact of steady-state interference on the measurement. Then the array output is converted into a single-channel signal, and the presence probability of substation noise at each time-frequency bin is estimated in real-time using an improved minimum-controlled recursive averaging algorithm, thus reducing the error caused by transient interference. The simulation results prove that the proposed method can effectively improve the accuracy of noise measurement.
- Open Access
- 15 May 2019
- Published by Wiley in Advances in Polymer Technology
- Vol. 2019, 1-8
Preparation and Sound Insulation Performance of Superfine Metal Powder/Nitrile-Butadiene Rubber-Polyvinyl Chloride Microcellular Foaming Material
Lightweight sound insulation materials have received much attention. In this study, a series of superfine metal powder (SFM)/nitrile-butadiene rubber (NBR)-polyvinyl chloride (PVC) microcellular foaming materials were prepared with NBR-PVC as matrix and SFM as modifiers by employing the method of molding foaming. Analysis on the morphology of cross section, pore size, and pore distribution possessed by SFM/NBR-PVC was conducted by scanning electron microscopy (SEM), as well as the image processing software of Image-Pro. Then detailed discussion on the effect of SFM with different mass fractions in the matrix on the foaming quality was provided. In the meanwhile, the performance of sound insulation was tested by four-channel impedance tube system. The results show significant improvement for foaming quality and sound insulation performance of NBR-PVC microcellular foaming material through the addition of SFM. In comparison with the pure NBR-PVC materials, the microcellular foaming material exhibits the best performance of foaming quality and sound insulation when the SFM content in matrix is 30 wt%. It is shown that the average pore diameter and the foaming capacity decrease by 60% and 31%, respectively, while the surface density increases by 131%. In the meantime, the sound insulation index of SFM/NBR-PVC microcellular material increases by 7.2 dB to 30.5 dB, which conforms to the requirements of new lightweight sound insulation materials in modern time. Finally, the mechanism of the optimization conducted for sound insulation performance after the addition of SMF is explained.
- 15 May 2019
- Published by Wiley in Advances in Polymer Technology
- Vol. 2019, 1-8
Open AccessPreparation and Sound Insulation Performance of Superfine Metal Powder/Nitrile-Butadiene Rubber-Polyvinyl Chloride Microcellular Foaming Material
Lightweight sound insulation materials have received much attention. In this study, a series of superfine metal powder (SFM)/nitrile-butadiene rubber (NBR)-polyvinyl chloride (PVC) microcellular foaming materials were prepared with NBR-PVC as matrix and SFM as modifiers by employing the method of molding foaming. Analysis on the morphology of cross section, pore size, and pore distribution possessed by SFM/NBR-PVC was conducted by scanning electron microscopy (SEM), as well as the image processing software of Image-Pro. Then detailed discussion on the effect of SFM with different mass fractions in the matrix on the foaming quality was provided. In the meanwhile, the performance of sound insulation was tested by four-channel impedance tube system. The results show significant improvement for foaming quality and sound insulation performance of NBR-PVC microcellular foaming material through the addition of SFM. In comparison with the pure NBR-PVC materials, the microcellular foaming material exhibits the best performance of foaming quality and sound insulation when the SFM content in matrix is 30 wt%. It is shown that the average pore diameter and the foaming capacity decrease by 60% and 31%, respectively, while the surface density increases by 131%. In the meantime, the sound insulation index of SFM/NBR-PVC microcellular material increases by 7.2 dB to 30.5 dB, which conforms to the requirements of new lightweight sound insulation materials in modern time. Finally, the mechanism of the optimization conducted for sound insulation performance after the addition of SMF is explained.