Diler Katircioglu-Bayel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Diler Katircioglu-Bayel has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Esmatullah Wahi̇b Toghan
Niğde Ömer Halisdemir Üniversitesi
1 shared publication Oner Yusuf Toraman
Niğde Ömer Halisdemir University
1 shared publication- Safak Gokhan Ozkan
Mining Engineering Department, Engineering Faculty, Istanbul University, Avcilar, Istanbul 34320, Turkey
1 shared publication
Latest Publications
- 16 February 2024
- Published by Elsevier in Advanced Powder Technology
- Vol. 35 (3)
Investigation of the use of glycerin as a by-product, pomace oil and paper wastewater as grinding aids in marble dust wastes
- 16 February 2024
- Published by Elsevier in Advanced Powder Technology
- Vol. 35 (3)
Investigation of the use of glycerin as a by-product, pomace oil and paper wastewater as grinding aids in marble dust wastes
- 31 July 2023
- Published by Bilimsel Madencilik Dergisi in Bilimsel Madencilik Dergisi
- Vol. 62 (2) , 61-66
Using glycerin, a by-product of biodiesel, as a grinding aid in the dry grinding of marble dust waste
Glycerin represents the primary by-product of biodiesel generation when vegetable oil is transesterified with ethanol or methanol. Nowadays, the need to turn to alternative materials is increasing due to the competition arising from developing technology and industry and the rapid consumption of Earth’s resources. It is essential to study how to prevent the depletion of natural resources and transform wastes into usable and valuable products. The use of waste glycerin (WG) as a grinding aid can constitute an alternative solution in terms of utilizing the excess glycerin resulting from biodiesel production. This paper investigated the usability of WG as a grinding aid in terms of grinding efficiency while planning to decrease the adverse impacts of waste on the environment via its efficient utilization. The dry grinding experiments conducted within the study’s scope researched the impacts of five biodiesel dosages (0%, 0.25%, 0.5%, 1%, and 2% by weight) on the product. The current research is promising in terms of preventing the depletion of natural resources and transforming waste into usable and valuable products. Furthermore, considerable enhancements were obtained in the grinding performance with the grinding aid utilized.
- 31 July 2023
- Published by Bilimsel Madencilik Dergisi in Bilimsel Madencilik Dergisi
- Vol. 62 (2) , 61-66
Using glycerin, a by-product of biodiesel, as a grinding aid in the dry grinding of marble dust waste
Glycerin represents the primary by-product of biodiesel generation when vegetable oil is transesterified with ethanol or methanol. Nowadays, the need to turn to alternative materials is increasing due to the competition arising from developing technology and industry and the rapid consumption of Earth’s resources. It is essential to study how to prevent the depletion of natural resources and transform wastes into usable and valuable products. The use of waste glycerin (WG) as a grinding aid can constitute an alternative solution in terms of utilizing the excess glycerin resulting from biodiesel production. This paper investigated the usability of WG as a grinding aid in terms of grinding efficiency while planning to decrease the adverse impacts of waste on the environment via its efficient utilization. The dry grinding experiments conducted within the study’s scope researched the impacts of five biodiesel dosages (0%, 0.25%, 0.5%, 1%, and 2% by weight) on the product. The current research is promising in terms of preventing the depletion of natural resources and transforming waste into usable and valuable products. Furthermore, considerable enhancements were obtained in the grinding performance with the grinding aid utilized.
- 1 March 2022
- Published by Konya Muhendislik Bilimleri Dergisi in Konya Journal of Engineering Sciences
- Vol. 10 (1) , 61-71
KARIŞTIRMALI BİLYALI DEĞİRMENDE BİYO-DOLGU MALZEMESİ ÜRETİMİNDE ÖĞÜTME YARDIMCILARININ ETKİSİ
Bu çalışma ile öğütme yardımcılarının tür ve dozajının öğütme verimi üzerine etkileri incelenmiş olup aynı zamanda atıkların çevre üzerindeki olumsuz etkilerinin verimli kullanım yoluyla azaltılması planlanmıştır. Yapılan kuru öğütme deneylerinde üç farklı gruptan altı tane öğütme yardımcısının, beş farklı dozajının (ağırlıkça, %0, %0,25, %0,5, %1 ve %2) ürün üzerindeki etkisi araştırılmıştır. Yapılan bu çalışma ile farklı gruplarda yer alan öğütme yardımcısı cins ve miktarının ürün boyutu (d80), boyut dağılımı ve sıcaklık (C°) üzerine etkisi araştırılmıştır. Bu çalışma, doğal kaynakların tükenmesini önlemek, atıkların değerli ve kullanılabilir ürüne dönüştürülmesi konusuna umut verici nitelikte bir çalışma olup aynı zamanda kullanılan öğütme yardımcıları ile öğütme performansı üzerinde önemli iyileşmelerin sağlandığı görülmüştür. Uygun dozajlarda öğütme yardımcısı kullanılarak yapılan deneylerde, öğütme yardımcısız yapılan deneylere nazaran ürün boyutu, sıcaklık ve boyut dağılımı açısından daha iyi sonuçlar elde edilmiştir.
- 1 March 2022
- Published by Konya Muhendislik Bilimleri Dergisi in Konya Journal of Engineering Sciences
- Vol. 10 (1) , 61-71
KARIŞTIRMALI BİLYALI DEĞİRMENDE BİYO-DOLGU MALZEMESİ ÜRETİMİNDE ÖĞÜTME YARDIMCILARININ ETKİSİ
Bu çalışma ile öğütme yardımcılarının tür ve dozajının öğütme verimi üzerine etkileri incelenmiş olup aynı zamanda atıkların çevre üzerindeki olumsuz etkilerinin verimli kullanım yoluyla azaltılması planlanmıştır. Yapılan kuru öğütme deneylerinde üç farklı gruptan altı tane öğütme yardımcısının, beş farklı dozajının (ağırlıkça, %0, %0,25, %0,5, %1 ve %2) ürün üzerindeki etkisi araştırılmıştır. Yapılan bu çalışma ile farklı gruplarda yer alan öğütme yardımcısı cins ve miktarının ürün boyutu (d80), boyut dağılımı ve sıcaklık (C°) üzerine etkisi araştırılmıştır. Bu çalışma, doğal kaynakların tükenmesini önlemek, atıkların değerli ve kullanılabilir ürüne dönüştürülmesi konusuna umut verici nitelikte bir çalışma olup aynı zamanda kullanılan öğütme yardımcıları ile öğütme performansı üzerinde önemli iyileşmelerin sağlandığı görülmüştür. Uygun dozajlarda öğütme yardımcısı kullanılarak yapılan deneylerde, öğütme yardımcısız yapılan deneylere nazaran ürün boyutu, sıcaklık ve boyut dağılımı açısından daha iyi sonuçlar elde edilmiştir.
- 12 August 2020
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 37 (5) , 1717-1727
Impact of Operating Parameters on the Breakage Process of Talc
- 12 August 2020
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 37 (5) , 1717-1727
Impact of Operating Parameters on the Breakage Process of Talc
- Open Access
Optimization of Operating Parameters on Dry Grinding of Calcite in a Stirred Media Mill Using the Box-Behnken Design
The optimization of the operating parameters of a stirred media mill in the dry grinding of calcite was investigated. A three-level Box-Behnken design was used for the purpose of examining the impact of four independent factors, the stirrer speed (SS), grinding time (GT), media filling ratio (MFR), and solid mass fraction (SMF), on the product particle size (d50). For the purpose of establishing an empirical correlation between operating parameters and responses, a series of experiments were carried out. Variance analysis showed a reasonably good value for d50 (R2 = 0.965). According to the software solutions, the optimum conditions for minimizing the d50 size were found to be 573 rpm stirrer speed, 11.18 min grinding time, 63% media filling ratio, and 11.52% solid mass fraction, with 3.78 µm for the d50 size. To verify the improvement of grinding, verification tests were performed using the above-mentioned optimum conditions and the average d50 size and standard deviation were found to be 3.83 µm and 0.025, respectively. The average d50 value obtained was smaller than those obtained in the 27 tests. Furthermore, when the optimum result obtained from the experiments was compared with the result obtained using the software, a 22% energy saving was achieved. The impacts of grinding on the structural characteristics of calcite particles were characterized by XRD analysis. XRD measurements indicated that no change was observed in the peak areas of ground calcite specimens compared to the untreated calcite specimen.
Open AccessOptimization of Operating Parameters on Dry Grinding of Calcite in a Stirred Media Mill Using the Box-Behnken Design
The optimization of the operating parameters of a stirred media mill in the dry grinding of calcite was investigated. A three-level Box-Behnken design was used for the purpose of examining the impact of four independent factors, the stirrer speed (SS), grinding time (GT), media filling ratio (MFR), and solid mass fraction (SMF), on the product particle size (d50). For the purpose of establishing an empirical correlation between operating parameters and responses, a series of experiments were carried out. Variance analysis showed a reasonably good value for d50 (R2 = 0.965). According to the software solutions, the optimum conditions for minimizing the d50 size were found to be 573 rpm stirrer speed, 11.18 min grinding time, 63% media filling ratio, and 11.52% solid mass fraction, with 3.78 µm for the d50 size. To verify the improvement of grinding, verification tests were performed using the above-mentioned optimum conditions and the average d50 size and standard deviation were found to be 3.83 µm and 0.025, respectively. The average d50 value obtained was smaller than those obtained in the 27 tests. Furthermore, when the optimum result obtained from the experiments was compared with the result obtained using the software, a 22% energy saving was achieved. The impacts of grinding on the structural characteristics of calcite particles were characterized by XRD analysis. XRD measurements indicated that no change was observed in the peak areas of ground calcite specimens compared to the untreated calcite specimen.
- 16 July 2019
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 37 (1) , 311-320
Effect of Combined Mechanical and Ultrasonic Milling on the Size Reduction of Talc
- 16 July 2019
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 37 (1) , 311-320
Effect of Combined Mechanical and Ultrasonic Milling on the Size Reduction of Talc
- Open Access
- 31 December 2018
- Published by Omer Halisdemir Universitesi Muhendislik Bilimleri Dergisi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- p. 1175-1179
ALEV GECİKTİRİCİ MİNERAL DOLGU MADDELERİ
The necessity of using flame retardant fillers or making several flame retardancy process in every area that needs heat and flame protection has become important again nowadays. For many people, the word filler is associated with cost reduction, but in recent years it has become more widely recognized that fillers modify all properties of the material in which they are mixed. Most commonly, fillers are used to assist processing and to upgrade the mechanical properties of the host polymer. In this research, it is emphasized the mineral based flame retardants and their effects.
- 31 December 2018
- Published by Omer Halisdemir Universitesi Muhendislik Bilimleri Dergisi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
- p. 1175-1179
Open AccessALEV GECİKTİRİCİ MİNERAL DOLGU MADDELERİ
The necessity of using flame retardant fillers or making several flame retardancy process in every area that needs heat and flame protection has become important again nowadays. For many people, the word filler is associated with cost reduction, but in recent years it has become more widely recognized that fillers modify all properties of the material in which they are mixed. Most commonly, fillers are used to assist processing and to upgrade the mechanical properties of the host polymer. In this research, it is emphasized the mineral based flame retardants and their effects.
- 24 September 2018
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 36 (2) , 399-408
Effect of Operating Parameters on the Breakage Process of Calcite in a Stirred Media Mill
- 24 September 2018
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 36 (2) , 399-408
Effect of Operating Parameters on the Breakage Process of Calcite in a Stirred Media Mill