Anand Jagota
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Anand Jagota has a total of 144 co-authors. Here are the top co-authors by number of shared publications:
- Chung-Yuen Hui
Sibley School of Mechanical and Aerospace Engineering, Cornell University, Ithaca, NY, USA
45 shared publications - Zezhou Liu
Field of Theoretical and Applied Mechanics, Sibley School of Mechanical and Aerospace Engineering, Cornell University, Ithaca, NY 14853, USA
8 shared publications - Ming Zheng
National Institute of Standards and Technology
6 shared publications - Haibin Wu
Department of Mechanical and Aerospace Engineering, Field of Theoretical and Applied Mechanics, Cornell University, Ithaca, NY 14853, USA.
5 shared publications - Shu Yang
Department of Materials Science and Engineering University of Pennsylvania Philadelphia Pennsylvania USA
5 shared publications - Xiaohui Frank Zhang
Department of Biomedical Engineering, University of Massachusetts Amherst, Amherst, MA
5 shared publications
Latest Publications
- 1 September 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (9)
Visualization of flow in soft elastohydrodynamic lubrication
Direct experimental measurement of in-plane velocity fields in soft elastohydrodynamic lubrication (EHL) contacts remains challenging due to the confined geometry and small film thickness. In this study, we visualize and quantify internal flow beneath a rigid glass sphere sliding on a compliant polydimethylsiloxane substrate using high-viscosity silicone oil seeded with 1–5 μm fluorescent tracer particles. Particle trajectories obtained from bottom-view imaging were processed into time-averaged velocity fields and streamlines, allowing direct comparison with numerical solutions of the Reynolds–elasticity EHL problem formulated in cylindrical coordinates. Friction measurements suggest that, at the concentrations used, tracer particles did not alter the fluid flow and lubrication regime, and film-thickness calculations confirmed that the particle size was compatible with the accessible gap under the tested loads and sliding velocities. The measurements reveal flow separation at the leading edge, reconvergence at the trailing edge, and depth-dependent transport pathways within the lubrication film. Comparison with cavitating and non-cavitating simulations further suggests that tensile-pressure regions strongly influence streamline topology and transport within the contact. These findings provide direct experimental evidence of internal flow organization in soft EHL and establish new links between pressure distribution and flow structure in compliant lubricated contacts.
- 1 September 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (9)
Visualization of flow in soft elastohydrodynamic lubrication
Direct experimental measurement of in-plane velocity fields in soft elastohydrodynamic lubrication (EHL) contacts remains challenging due to the confined geometry and small film thickness. In this study, we visualize and quantify internal flow beneath a rigid glass sphere sliding on a compliant polydimethylsiloxane substrate using high-viscosity silicone oil seeded with 1–5 μm fluorescent tracer particles. Particle trajectories obtained from bottom-view imaging were processed into time-averaged velocity fields and streamlines, allowing direct comparison with numerical solutions of the Reynolds–elasticity EHL problem formulated in cylindrical coordinates. Friction measurements suggest that, at the concentrations used, tracer particles did not alter the fluid flow and lubrication regime, and film-thickness calculations confirmed that the particle size was compatible with the accessible gap under the tested loads and sliding velocities. The measurements reveal flow separation at the leading edge, reconvergence at the trailing edge, and depth-dependent transport pathways within the lubrication film. Comparison with cavitating and non-cavitating simulations further suggests that tensile-pressure regions strongly influence streamline topology and transport within the contact. These findings provide direct experimental evidence of internal flow organization in soft EHL and establish new links between pressure distribution and flow structure in compliant lubricated contacts.
- 24 August 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (35) , 25454-25466
Particle Entrainment in Lubricants Leads to Extended Mixed Lubrication in Soft Tribology
Particle-laden lubricants provide a versatile platform for tuning frictional behavior across boundary, mixed, and elastohydrodynamic (EHL) regimes in soft tribological systems. In this study, we examine the evolution of an extended mixed regime between poly(dimethylsiloxane) (PDMS) tribopairs lubricated with poly(methyl methacrylate) (PMMA) suspensions in low-viscosity squalene and high-viscosity diisodecyl phthalate (DIDP). Smaller particles at low concentrations delay entrainment and slow film formation, while larger particles consistently reduce friction by enhancing load distribution and promoting separation that limits solid–solid contact. These effects, driven by particle confinement and structural rearrangements, generate clear deviations from classical Stribeck behavior. Two characteristic points mark the onset and termination of this extended mixed regime. We observe that the velocity corresponding to the beginning of mixed regime transition, Um1, is largely independent of particle size and volume fraction in squalene suspensions due to a restrictive particle confinement within the tribopairs that primarily allows solvent movement through the gap. In contrast, DIDP suspensions have a lower onset velocity (Um1) as the higher solvent viscosity promotes particle entrainment into the lubrication gap. The velocity corresponding to the end of the mixed regime transition (Um2) decreases with increasing volume fraction, indicating the formation of a fully developed lubrication film that separates the PDMS tribopairs. Hamrock–Dowson film thickness estimates combined with experimental relaxation measurements are used to quantify the development of the lubrication film as sliding speed increases and the system approaches the EHL regime. The findings from this study establish particle entrainment and suspension viscosity as key mechanisms for expanding and stabilizing the extended mixed regime.
- 24 August 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (35) , 25454-25466
Particle Entrainment in Lubricants Leads to Extended Mixed Lubrication in Soft Tribology
Particle-laden lubricants provide a versatile platform for tuning frictional behavior across boundary, mixed, and elastohydrodynamic (EHL) regimes in soft tribological systems. In this study, we examine the evolution of an extended mixed regime between poly(dimethylsiloxane) (PDMS) tribopairs lubricated with poly(methyl methacrylate) (PMMA) suspensions in low-viscosity squalene and high-viscosity diisodecyl phthalate (DIDP). Smaller particles at low concentrations delay entrainment and slow film formation, while larger particles consistently reduce friction by enhancing load distribution and promoting separation that limits solid–solid contact. These effects, driven by particle confinement and structural rearrangements, generate clear deviations from classical Stribeck behavior. Two characteristic points mark the onset and termination of this extended mixed regime. We observe that the velocity corresponding to the beginning of mixed regime transition, Um1, is largely independent of particle size and volume fraction in squalene suspensions due to a restrictive particle confinement within the tribopairs that primarily allows solvent movement through the gap. In contrast, DIDP suspensions have a lower onset velocity (Um1) as the higher solvent viscosity promotes particle entrainment into the lubrication gap. The velocity corresponding to the end of the mixed regime transition (Um2) decreases with increasing volume fraction, indicating the formation of a fully developed lubrication film that separates the PDMS tribopairs. Hamrock–Dowson film thickness estimates combined with experimental relaxation measurements are used to quantify the development of the lubrication film as sliding speed increases and the system approaches the EHL regime. The findings from this study establish particle entrainment and suspension viscosity as key mechanisms for expanding and stabilizing the extended mixed regime.
- 9 March 2026
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 20 (11) , 9560-9571
Overcoming van der Waals Bundling: Molecular Wedges Enable Sonication-Free Dispersion of Single-Walled Carbon Nanotubes
Single-walled carbon nanotubes (SWCNTs) naturally bundle due to strong van der Waals interactions, posing a significant challenge to their dispersion and applications. Conventional methods require ultrasonication or extended shear mixing, which are energy-intensive, can damage the nanotubes, and/or incur high process costs and low throughput. Here, we show that small molecular wedges, which are formed by reacting wedge precursors (e.g., 1-octanol, ammonia, n-hexylamine) with minimal amounts of superacids (e.g., chlorosulfonic acid, CSA), can intercalate the nanotube bundles, markedly reducing van der Waals interactions. Modeling based on the Euler-Bernoulli beam theory reveals a relationship between the pry-open length and the molecular wedge size, adhesion energy, and the nanotube's bending stiffness. Wedged SWCNTs exhibit a 130-fold increase in dispersion efficiency with DOC and a 14-fold increase with single-stranded DNA, all while preserving the nanotube length. Even in organic solvents, where gentle stirring typically yields almost no dispersion, the wedging approach achieves a dispersion yield of (6,5)-SWCNTs up to ∼2.7% (O.D. ∼13). Furthermore, this method enables one-pot sp3 quantum defect functionalization with improved uniformity and modulates defect photoluminescence by replacing defect-pairing groups with wedges. This versatile wedging approach provides a scalable route for processing SWCNTs and is expected to be broadly adaptable to other van der Waals materials.
- 9 March 2026
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 20 (11) , 9560-9571
Overcoming van der Waals Bundling: Molecular Wedges Enable Sonication-Free Dispersion of Single-Walled Carbon Nanotubes
Single-walled carbon nanotubes (SWCNTs) naturally bundle due to strong van der Waals interactions, posing a significant challenge to their dispersion and applications. Conventional methods require ultrasonication or extended shear mixing, which are energy-intensive, can damage the nanotubes, and/or incur high process costs and low throughput. Here, we show that small molecular wedges, which are formed by reacting wedge precursors (e.g., 1-octanol, ammonia, n-hexylamine) with minimal amounts of superacids (e.g., chlorosulfonic acid, CSA), can intercalate the nanotube bundles, markedly reducing van der Waals interactions. Modeling based on the Euler-Bernoulli beam theory reveals a relationship between the pry-open length and the molecular wedge size, adhesion energy, and the nanotube's bending stiffness. Wedged SWCNTs exhibit a 130-fold increase in dispersion efficiency with DOC and a 14-fold increase with single-stranded DNA, all while preserving the nanotube length. Even in organic solvents, where gentle stirring typically yields almost no dispersion, the wedging approach achieves a dispersion yield of (6,5)-SWCNTs up to ∼2.7% (O.D. ∼13). Furthermore, this method enables one-pot sp3 quantum defect functionalization with improved uniformity and modulates defect photoluminescence by replacing defect-pairing groups with wedges. This versatile wedging approach provides a scalable route for processing SWCNTs and is expected to be broadly adaptable to other van der Waals materials.
- 24 February 2026
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 212
Trapped fluids and dry zones: Adhesion’s role in soft lubrication instabilities
- 24 February 2026
- Published by Elsevier in Journal of the Mechanics and Physics of Solids
- Vol. 212
Trapped fluids and dry zones: Adhesion’s role in soft lubrication instabilities
- Open Access
- 10 February 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (7) , 5440-5451
A Layer-Based Model for Frictional Sliding of Pillar Arrays
Bioinspired micropatterned surfaces have been studied as a way to enhance or control interfacial mechanical properties. Here, we study friction for the relative sliding of two interdigitated pillar surfaces. The overall frictional force originates from individual pillar-pillar interactions across the interface as well as the interpillar coupling within each substrate. In this study, we develop a layer-based physical model to simulate the contact and sliding behavior of these pillar arrays. The system is modeled as comprising four layers of nodes, with uniform shear displacement applied to the top layer, while the bottom one is held fixed. Nodes in the inner two layers represent the joints between the pillars and the substrate. The model predicts shear friction force and reveals underlying deformation mechanisms at various misorientations and height overlaps, in good agreement with measured friction in sliding experiments.
- 10 February 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (7) , 5440-5451
Open AccessA Layer-Based Model for Frictional Sliding of Pillar Arrays
Bioinspired micropatterned surfaces have been studied as a way to enhance or control interfacial mechanical properties. Here, we study friction for the relative sliding of two interdigitated pillar surfaces. The overall frictional force originates from individual pillar-pillar interactions across the interface as well as the interpillar coupling within each substrate. In this study, we develop a layer-based physical model to simulate the contact and sliding behavior of these pillar arrays. The system is modeled as comprising four layers of nodes, with uniform shear displacement applied to the top layer, while the bottom one is held fixed. Nodes in the inner two layers represent the joints between the pillars and the substrate. The model predicts shear friction force and reveals underlying deformation mechanisms at various misorientations and height overlaps, in good agreement with measured friction in sliding experiments.
- Open Access
- 6 August 2025
- Vol. 122 (32)
Role of wettability, adhesion, and instabilities in transitions during lubricated sliding friction.
Lubricated contacts in soft materials are important in various engineering systems and natural settings. Three major lubrication regimes are boundary (BL), mixed (ML), and elastohydrodynamic (EHL) lubrication, where the contact region is dry, partially wetted, or fully wetted, respectively. The transition between these regimes is insufficiently understood, especially for soft contacts, which impedes desired control of lubricated sliding friction. Here, we report on the role of solid wettability and adhesion on these transitions. Wettability of glycerol on polydimethylsiloxane (PDMS) surfaces and adhesion between a glass indenter and PDMS were varied by exposure of the PDMS to an ultraviolet light-ozone cleaner. By combining friction tests and visualization, we demonstrate that the transition from ML to BL regime is dominated by the wettability of the lubricant; increasing wettability of glycerol makes removal of liquid from the contact region more difficult. Transition from EHL to ML is related to a series of events with increasing normal load, which are thinning of the lubricant layer, sudden jump to contact between the glass indenter and solid substrate across a gap of tens of nanometers, and attendant mechanical instabilities such as wrinkling and stick-slip. These results provide a deeper understanding of transitions in lubricated frictional behavior of soft materials which govern the maximum and minimum friction achievable.
- 6 August 2025
- Vol. 122 (32)
Open AccessRole of wettability, adhesion, and instabilities in transitions during lubricated sliding friction.
Lubricated contacts in soft materials are important in various engineering systems and natural settings. Three major lubrication regimes are boundary (BL), mixed (ML), and elastohydrodynamic (EHL) lubrication, where the contact region is dry, partially wetted, or fully wetted, respectively. The transition between these regimes is insufficiently understood, especially for soft contacts, which impedes desired control of lubricated sliding friction. Here, we report on the role of solid wettability and adhesion on these transitions. Wettability of glycerol on polydimethylsiloxane (PDMS) surfaces and adhesion between a glass indenter and PDMS were varied by exposure of the PDMS to an ultraviolet light-ozone cleaner. By combining friction tests and visualization, we demonstrate that the transition from ML to BL regime is dominated by the wettability of the lubricant; increasing wettability of glycerol makes removal of liquid from the contact region more difficult. Transition from EHL to ML is related to a series of events with increasing normal load, which are thinning of the lubricant layer, sudden jump to contact between the glass indenter and solid substrate across a gap of tens of nanometers, and attendant mechanical instabilities such as wrinkling and stick-slip. These results provide a deeper understanding of transitions in lubricated frictional behavior of soft materials which govern the maximum and minimum friction achievable.
- Open Access
- 3 July 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (27) , 17716-17724
Understanding Viral-Glycocalyx Interactions Using Brush-Linked to Cross-Linked Models
The interaction of viruses with cells is mediated by the glycocalyx, a ubiquitous cell coating layer. Here, we present a study of the effects of the cellular glycocalyx, a complex outer cell structure, on viral internalization. Using both simulations and experiments, we have shown that the structure of the glycocalyx, specifically the number of cross-links within it, can greatly influence the ability of a virus to infect a cell. We show that the presence of the glycocalyx plays a direct role in viral internalization, and targeting the glycocalyx can be a potential avenue for future therapies. Overall, by comparison with experimental results, we conclude that a brush-like glycocalyx model is the more appropriate computational model compared to its partially cross-linked versions.
- 3 July 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (27) , 17716-17724
Open AccessUnderstanding Viral-Glycocalyx Interactions Using Brush-Linked to Cross-Linked Models
The interaction of viruses with cells is mediated by the glycocalyx, a ubiquitous cell coating layer. Here, we present a study of the effects of the cellular glycocalyx, a complex outer cell structure, on viral internalization. Using both simulations and experiments, we have shown that the structure of the glycocalyx, specifically the number of cross-links within it, can greatly influence the ability of a virus to infect a cell. We show that the presence of the glycocalyx plays a direct role in viral internalization, and targeting the glycocalyx can be a potential avenue for future therapies. Overall, by comparison with experimental results, we conclude that a brush-like glycocalyx model is the more appropriate computational model compared to its partially cross-linked versions.
- Open Access
- 16 December 2024
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 40 (52) , 27206-27215
Microdroplet Resuspension Off Surfaces
Understanding the resuspension of droplets from surfaces into air is important for elucidating a range of processes such as disease transmission of airborne pathogens and determining environmental contamination and the effectiveness of cleaning procedures. The resuspension condition is defined as the escape velocity of a droplet from a surface. This study investigated the dynamics of microliter-sized droplet resuspension off surfaces utilizing a novel free-fall device. We studied surfaces with three different wettabilities, three droplet volumes, and substrate velocities ranging from 0 to 3.5 m/s for deionized water and viscous droplets representing a prototype saliva substitute. Experimental results provide quantitative results for the increased propensity for drop resuspension for more hydrophobic surfaces, larger droplet volume, and higher velocity. By using high-speed imaging, we segment the resuspension process into four stages: initial equilibrium, deformation, elongation, and breakage. Experimental results are generalized as a machine-learning-derived decision surface, which predicts resuspension by defining a 2D decision boundary in our 3D parameter space. We present a simple physical model, corroborated by computational fluid dynamics simulations, for the dynamics of resuspension that explains the process and is in good agreement with the experiments.
- 16 December 2024
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 40 (52) , 27206-27215
Open AccessMicrodroplet Resuspension Off Surfaces
Understanding the resuspension of droplets from surfaces into air is important for elucidating a range of processes such as disease transmission of airborne pathogens and determining environmental contamination and the effectiveness of cleaning procedures. The resuspension condition is defined as the escape velocity of a droplet from a surface. This study investigated the dynamics of microliter-sized droplet resuspension off surfaces utilizing a novel free-fall device. We studied surfaces with three different wettabilities, three droplet volumes, and substrate velocities ranging from 0 to 3.5 m/s for deionized water and viscous droplets representing a prototype saliva substitute. Experimental results provide quantitative results for the increased propensity for drop resuspension for more hydrophobic surfaces, larger droplet volume, and higher velocity. By using high-speed imaging, we segment the resuspension process into four stages: initial equilibrium, deformation, elongation, and breakage. Experimental results are generalized as a machine-learning-derived decision surface, which predicts resuspension by defining a 2D decision boundary in our 3D parameter space. We present a simple physical model, corroborated by computational fluid dynamics simulations, for the dynamics of resuspension that explains the process and is in good agreement with the experiments.
- Open Access
- 24 September 2024
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry B
- Vol. 128 (47) , 11546-11553
Biomechanics Model to Characterize Atomic Force Microscopy-Based Virus–Host Cell Adhesion Measurements
We present a model for virus-cell adhesion that can be used for quantitative extraction of adhesive properties from atomic force microscopy (AFM)-based force spectroscopy measurements. We extend a previously reported continuum model of viral cell interactions based on a single parameter representing adhesive energy density by using a cohesive zone model in which adhesion is represented by two parameters, a pull-off stress and associated characteristic displacement. This approach accounts for the deformability of the adhesive receptors, such as the Spike protein and transmembrane immunoglobulin and mucin domain (TIM) family that mediate adhesion of SARS-CoV-2 and Ebola viruses, and the omnipresent glycocalyx. Our model represents receptors as a Winkler foundation and aims to predict the pull-off force needed to break the adhesion between the virus and the cell. By comparing the force-separation curves simulated by the model and experimental data, we found that the model can effectively explain the AFM pull-off force trace, thus allowing quantification of the adhesion parameters. Our model provides a more refined understanding of viral cell adhesion and also establishes a framework for interpreting and predicting AFM force spectroscopy measurements.
- 24 September 2024
- Published by American Chemical Society (ACS) in The Journal of Physical Chemistry B
- Vol. 128 (47) , 11546-11553
Open AccessBiomechanics Model to Characterize Atomic Force Microscopy-Based Virus–Host Cell Adhesion Measurements
We present a model for virus-cell adhesion that can be used for quantitative extraction of adhesive properties from atomic force microscopy (AFM)-based force spectroscopy measurements. We extend a previously reported continuum model of viral cell interactions based on a single parameter representing adhesive energy density by using a cohesive zone model in which adhesion is represented by two parameters, a pull-off stress and associated characteristic displacement. This approach accounts for the deformability of the adhesive receptors, such as the Spike protein and transmembrane immunoglobulin and mucin domain (TIM) family that mediate adhesion of SARS-CoV-2 and Ebola viruses, and the omnipresent glycocalyx. Our model represents receptors as a Winkler foundation and aims to predict the pull-off force needed to break the adhesion between the virus and the cell. By comparing the force-separation curves simulated by the model and experimental data, we found that the model can effectively explain the AFM pull-off force trace, thus allowing quantification of the adhesion parameters. Our model provides a more refined understanding of viral cell adhesion and also establishes a framework for interpreting and predicting AFM force spectroscopy measurements.
- 12 January 2024
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 20 (7) , 1459-1466
Sliding friction of a pillar array interface: part II, contact mechanics of single pillar pairs
A computational model is used to study contact sliding of soft single pillar pairs.
- 12 January 2024
- Published by Royal Society of Chemistry (RSC) in Soft Matter
- Vol. 20 (7) , 1459-1466
Sliding friction of a pillar array interface: part II, contact mechanics of single pillar pairs
A computational model is used to study contact sliding of soft single pillar pairs.