Kamal Uddin Ahamad
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kamal Uddin Ahamad has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
Binanda Khungur Narzary
6 shared publicationsMohammad Jawed
Department of Civil Engineering, Indian Institute of Technology Guwahati, Guwahati, 781039, Assam, India
5 shared publications- Iftak Hussain
Sibley School of Mechanical and Aerospace Engineering, Cornell University, Ithaca, NY 14850
4 shared publications Bishal Talukdar
Department of Civil Engineering, Tezpur University, Napaam, India
3 shared publicationsBiswajit Bhagowati
Department of Civil Engineering, Tezpur University, Napaam, Assam 784028, India
3 shared publicationsPabitra Nath
3 shared publications
Latest Publications
- 25 May 2026
- Published by Springer Nature in Waste and Biomass Valorization
- Vol. 17 (13) , 8883-8908
Waste-to-Energy Valorization of Poultry, Pig and Cow Dung Slurry Using Microbial Fuel Cells: Optimization and ANN Modeling for Rural Decentralized Application
- 25 May 2026
- Published by Springer Nature in Waste and Biomass Valorization
- Vol. 17 (13) , 8883-8908
Waste-to-Energy Valorization of Poultry, Pig and Cow Dung Slurry Using Microbial Fuel Cells: Optimization and ANN Modeling for Rural Decentralized Application
- Open Access
- 30 April 2026
- Published by Elsevier in SSRN Electronic Journal
Spatial distribution of microplastic contamination in urban groundwater of Delhi, India: Characteristics and health risk assessment
Microplastic contamination is increasingly recognized as an emerging environmental and public health concern in urban groundwater systems, yet evidence from megacities remains limited. This study investigates the occurrence, characteristics and associated risks of microplastics and other water quality parameters in groundwater across landfill, industrial and residential zones of National Capital Territory of Delhi. Microplastics were detected in all groundwater samples with concentrations ranging from 2 to 28 particles/L (mean 14 ± 6.53; median 14). Significant spatial variability was observed among the zones (ANOVA, p < 0.001), with the landfill zone exhibiting the highest load (20.16 ± 6.17 particles/L), exceeding the industrial (16 ± 4.20 particles/L) and residential zone (9 ± 2.86 particles/L). Peak contamination was observed at downstream and near landfill sites (e.g., GW20; GW15-GW18), indicating strong influence of waste handling and localized recycling activities on the overall microplastic contamination. Size distribution was dominated by small fractions (50-500 µm; 80.45%), and fibres were the prevailing morphology (63.8%), followed by fragments (26.4%). Dominant polymers were PE (34%), PET (28.5%) and PP (15.59%), with the presence of high hazard polymers (PVC, PU) near the landfill. The EDI of microplastics via groundwater ingestion ranged from 0.415 to 1.754 particles/kg bw/day, with the highest exposure observed in landfill areas and among infants, indicating increased vulnerability. Risk indices indicated minor contamination load (PLI 1.2-4.66) but elevated toxicity weighted hazards at hotspot sites (high PHI and MCF), underscoring the need for risk-based monitoring, targeted mitigation through policy interventions and infrastructure improvements to safeguard groundwater in landfill and industrial impacted aquifers.
- 30 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSpatial distribution of microplastic contamination in urban groundwater of Delhi, India: Characteristics and health risk assessment
Microplastic contamination is increasingly recognized as an emerging environmental and public health concern in urban groundwater systems, yet evidence from megacities remains limited. This study investigates the occurrence, characteristics and associated risks of microplastics and other water quality parameters in groundwater across landfill, industrial and residential zones of National Capital Territory of Delhi. Microplastics were detected in all groundwater samples with concentrations ranging from 2 to 28 particles/L (mean 14 ± 6.53; median 14). Significant spatial variability was observed among the zones (ANOVA, p < 0.001), with the landfill zone exhibiting the highest load (20.16 ± 6.17 particles/L), exceeding the industrial (16 ± 4.20 particles/L) and residential zone (9 ± 2.86 particles/L). Peak contamination was observed at downstream and near landfill sites (e.g., GW20; GW15-GW18), indicating strong influence of waste handling and localized recycling activities on the overall microplastic contamination. Size distribution was dominated by small fractions (50-500 µm; 80.45%), and fibres were the prevailing morphology (63.8%), followed by fragments (26.4%). Dominant polymers were PE (34%), PET (28.5%) and PP (15.59%), with the presence of high hazard polymers (PVC, PU) near the landfill. The EDI of microplastics via groundwater ingestion ranged from 0.415 to 1.754 particles/kg bw/day, with the highest exposure observed in landfill areas and among infants, indicating increased vulnerability. Risk indices indicated minor contamination load (PLI 1.2-4.66) but elevated toxicity weighted hazards at hotspot sites (high PHI and MCF), underscoring the need for risk-based monitoring, targeted mitigation through policy interventions and infrastructure improvements to safeguard groundwater in landfill and industrial impacted aquifers.
- 6 January 2026
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 16 (1) , 29
Optimizing salt bridge parameters in dual chambered microbial fuel cells with cow and pig dung slurry as substrate
- 6 January 2026
- Published by Springer Nature in Biomass Conversion and Biorefinery
- Vol. 16 (1) , 29
Optimizing salt bridge parameters in dual chambered microbial fuel cells with cow and pig dung slurry as substrate
- Open Access
- 9 January 2024
- Published by IWA Publishing in Water Quality Research Journal
- Vol. 59 (1) , 1-25
Examining the effectiveness of artificially replicated lake systems in predicting eutrophication indicators: a comparative data-driven analysis
Data-driven models for the prediction of lake eutrophication essentially rely on water quality datasets for a longer duration. If such data are not readily available, lake management through data-driven modeling becomes impractical. So, a novel approach is presented here for the prediction of eutrophication indicators, such as dissolved oxygen, Secchi depth, total nitrogen, and total phosphorus, in the waterbodies of Assam, India. These models were developed using water quality datasets collected through laboratory investigation in artificially simulated lake systems. Two artificial prototype lakes were eutrophied in a controlled environment with the gradual application of wastewater. A periodic assessment of water quality was done for model development. Data-driven modeling in the form of multilayer perceptron (MLP), time-delay neural network (TDNN), support vector regression (SVR), and Gaussian process regression (GPR) were utilized. The trained model's accuracy was evaluated based on statistical parameters and a reasonable correlation was observed between targeted and model predicted values. Finally, the trained models were tested against some natural waterbodies in Assam and a satisfactory prediction accuracy was obtained. TDNN and GPR models were found superior compared to other methods. Results of the study indicate feasibility of the adopted modeling approach in predicting lake eutrophication when periodic water quality data are limited for the waterbody under consideration.
- 9 January 2024
- Published by IWA Publishing in Water Quality Research Journal
- Vol. 59 (1) , 1-25
Open AccessExamining the effectiveness of artificially replicated lake systems in predicting eutrophication indicators: a comparative data-driven analysis
Data-driven models for the prediction of lake eutrophication essentially rely on water quality datasets for a longer duration. If such data are not readily available, lake management through data-driven modeling becomes impractical. So, a novel approach is presented here for the prediction of eutrophication indicators, such as dissolved oxygen, Secchi depth, total nitrogen, and total phosphorus, in the waterbodies of Assam, India. These models were developed using water quality datasets collected through laboratory investigation in artificially simulated lake systems. Two artificial prototype lakes were eutrophied in a controlled environment with the gradual application of wastewater. A periodic assessment of water quality was done for model development. Data-driven modeling in the form of multilayer perceptron (MLP), time-delay neural network (TDNN), support vector regression (SVR), and Gaussian process regression (GPR) were utilized. The trained model's accuracy was evaluated based on statistical parameters and a reasonable correlation was observed between targeted and model predicted values. Finally, the trained models were tested against some natural waterbodies in Assam and a satisfactory prediction accuracy was obtained. TDNN and GPR models were found superior compared to other methods. Results of the study indicate feasibility of the adopted modeling approach in predicting lake eutrophication when periodic water quality data are limited for the waterbody under consideration.
- 21 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (17) , 19314-19321
Dual Mode Smartphone Based Sensing for Accurate Estimation of Sulphate and Chloride in Water
A smartphone-based dual-mode sensing system for accurate and reliable estimation of sulphate and chloride level in water is reported. The designed sensor is based on the detection of transmitted modulated signal (for spectrophotometric based study) and scattered signal intensities (for turbidimetric based study) from a sample. The ambient light sensor (ALS) of the phone has been used as a detector for receiving the modulated signal for both the sensing modes of studies. The applicability of the designed tool has been realized through monitoring of sulphate and chloride ions concentrations in water. A custom-designed application has been developed to convert the sensing system into a standalone tool that converts the sensing data into a readable format. The proposed sensing system could emerge as an alternative platform which can be utilized for monitoring of other parameters of water and other media as well.
- 21 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (17) , 19314-19321
Dual Mode Smartphone Based Sensing for Accurate Estimation of Sulphate and Chloride in Water
A smartphone-based dual-mode sensing system for accurate and reliable estimation of sulphate and chloride level in water is reported. The designed sensor is based on the detection of transmitted modulated signal (for spectrophotometric based study) and scattered signal intensities (for turbidimetric based study) from a sample. The ambient light sensor (ALS) of the phone has been used as a detector for receiving the modulated signal for both the sensing modes of studies. The applicability of the designed tool has been realized through monitoring of sulphate and chloride ions concentrations in water. A custom-designed application has been developed to convert the sensing system into a standalone tool that converts the sensing data into a readable format. The proposed sensing system could emerge as an alternative platform which can be utilized for monitoring of other parameters of water and other media as well.
- 1 March 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering, Part B: Pavements
- Vol. 147 (1) , 04020084
Estimation of Equivalent Modulus of Fine-Grained Subgrade Soil from Numerical Model
Resilient modulus of subgrade represents soil stiffness with regard to in-situ stress in a controlled laboratory environment that can be measured from repeated load triaxial test. However, the expensive and time-consuming procedure involved in its measurements induces various researchers to develop a methodology to estimate parameters analogous to the resilient modulus. Recently, the California bearing ratio (CBR) test was used to estimate equivalent modulus as the soil stiffness using a repeated load approach. The present paper proposed a rational methodology to estimate the equivalent modulus of soil ( ) using a numerical approach. The mechanical characterization of a soil sample was investigated by conducting a CBR test, repeated load CBR (RLCBR) test, and direct shear test. Modeling of the RLCBR test was done using the MC soil model to estimate the equivalent modulus of a CBR sample that was then converted to under half-space boundary conditions using a finite element model (FEM). The comparison of with resilient modulus obtained from a soaked CBR sample indicated strong agreement with a coefficient of determination of 0.96, indicating that the proposed methodology provides an equivalent modulus of soil as a resilient modulus with acceptable accuracy.- 1 March 2021
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering, Part B: Pavements
- Vol. 147 (1) , 04020084
Estimation of Equivalent Modulus of Fine-Grained Subgrade Soil from Numerical Model
Resilient modulus of subgrade represents soil stiffness with regard to in-situ stress in a controlled laboratory environment that can be measured from repeated load triaxial test. However, the expensive and time-consuming procedure involved in its measurements induces various researchers to develop a methodology to estimate parameters analogous to the resilient modulus. Recently, the California bearing ratio (CBR) test was used to estimate equivalent modulus as the soil stiffness using a repeated load approach. The present paper proposed a rational methodology to estimate the equivalent modulus of soil ( ) using a numerical approach. The mechanical characterization of a soil sample was investigated by conducting a CBR test, repeated load CBR (RLCBR) test, and direct shear test. Modeling of the RLCBR test was done using the MC soil model to estimate the equivalent modulus of a CBR sample that was then converted to under half-space boundary conditions using a finite element model (FEM). The comparison of with resilient modulus obtained from a soaked CBR sample indicated strong agreement with a coefficient of determination of 0.96, indicating that the proposed methodology provides an equivalent modulus of soil as a resilient modulus with acceptable accuracy.- 1 June 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering, Part B: Pavements
- Vol. 146 (2) , 04020004
Equivalent Modulus for Fine-Grained Subgrade Soil
Previous studies on repeated-load California bearing ratio (RLCBR) tests have described its application to estimate the equivalent modulus of soil as stiffness modulus under repeated load. However, the effects of physical state and stress state on the modulus have not been discussed in detail. The present study was carried out, therefore, to evaluate the influence of physical state and stress state on the equivalent modulus of CBR samples using RLCBR tests. Samples were prepared using fine-grained soil to carry out the RLCBR tests under various physical and stress states. A deformation model was developed to estimate the equivalent modulus of the CBR sample from the results of RLCBR testing. Finally, the equivalent modulus of the soil was estimated using a finite-element model. The values of equivalent modulus were found to be comparable to those of resilient modulus obtained from correlation, which indicates that the method followed in the present study is useful to estimate the stiffness modulus of soil with an acceptable accuracy.
- 1 June 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Transportation Engineering, Part B: Pavements
- Vol. 146 (2) , 04020004
Equivalent Modulus for Fine-Grained Subgrade Soil
Previous studies on repeated-load California bearing ratio (RLCBR) tests have described its application to estimate the equivalent modulus of soil as stiffness modulus under repeated load. However, the effects of physical state and stress state on the modulus have not been discussed in detail. The present study was carried out, therefore, to evaluate the influence of physical state and stress state on the equivalent modulus of CBR samples using RLCBR tests. Samples were prepared using fine-grained soil to carry out the RLCBR tests under various physical and stress states. A deformation model was developed to estimate the equivalent modulus of the CBR sample from the results of RLCBR testing. Finally, the equivalent modulus of the soil was estimated using a finite-element model. The values of equivalent modulus were found to be comparable to those of resilient modulus obtained from correlation, which indicates that the method followed in the present study is useful to estimate the stiffness modulus of soil with an acceptable accuracy.
- 1 March 2020
- Published by Elsevier in Measurement
- Vol. 154
Estimation of trace-mercury concentration in water using a smartphone
- 1 March 2020
- Published by Elsevier in Measurement
- Vol. 154
Estimation of trace-mercury concentration in water using a smartphone