Namrata Sengar
Research Subjects
Namrata Sengar has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
P. Dashora
4 shared publicationsP. Rajawat
3 shared publicationsS. Mahavar
3 shared publicationsM. Verma
Department of Physics, University of Rajasthan, Jaipur 302004, Rajasthan, India
2 shared publications- Abhilasha Mishra
Graphic Era University
1 shared publication - Adeeba Mirza
Graphic Era Deemed to be University Department of Chemistry Dehradun
1 shared publication
Latest Publications
- 29 September 2026
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Energy
- p. 1-10
Study of hydrophobic coatings and potential water savings in solar power plants
This study explores the challenges related to dust deposition on solar photovoltaic (PV) systems. Review of earlier works suggests solar PV performance is significantly affected by the dust deposition and the power loss can vary from 10% to more than 60% in some cases depending on the location. Hydrophobic coatings can offer a potential pathway for reducing dust deposition and water saving in cleaning operations. This paper presents the comparative study of the four commercially available and one developed silica-based hydrophobic coating to estimate the quantity of the water required for cleaning of the dust. Comparative experimental tests reveal that the developed coating has the highest contact angle (145°), least contact angle hysteresis (5°) and least surface free energy (17.4 mN/m) as compared to the other coatings. The prepared coating slightly decreased the visible light transmittance of the glass from 92.4% to 90.23%. The water saving with the hydrophobic coatings is found to be in the range 28%–55%; the highest water saving is observed with the developed coating as it is almost near to a superhydrophobic coating in behaviour. Furthermore, the scope for future work and challenges related to the development and use of hydrophobic coatings in the solar area are discussed.
- 29 September 2026
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Energy
- p. 1-10
Study of hydrophobic coatings and potential water savings in solar power plants
This study explores the challenges related to dust deposition on solar photovoltaic (PV) systems. Review of earlier works suggests solar PV performance is significantly affected by the dust deposition and the power loss can vary from 10% to more than 60% in some cases depending on the location. Hydrophobic coatings can offer a potential pathway for reducing dust deposition and water saving in cleaning operations. This paper presents the comparative study of the four commercially available and one developed silica-based hydrophobic coating to estimate the quantity of the water required for cleaning of the dust. Comparative experimental tests reveal that the developed coating has the highest contact angle (145°), least contact angle hysteresis (5°) and least surface free energy (17.4 mN/m) as compared to the other coatings. The prepared coating slightly decreased the visible light transmittance of the glass from 92.4% to 90.23%. The water saving with the hydrophobic coatings is found to be in the range 28%–55%; the highest water saving is observed with the developed coating as it is almost near to a superhydrophobic coating in behaviour. Furthermore, the scope for future work and challenges related to the development and use of hydrophobic coatings in the solar area are discussed.
- Open Access
- 28 May 2025
- Published by University of Johannesburg in Journal of BRICS Studies
- Vol. 4 (1) , 17-26
Prospective Solar Energy Technologies for Sustainable and Inclusive Development in BRICS Countries
The climate change scenario observed in the last few years calls for immediate attention and planned action. One of the major factors responsible for climate change is fossil fuel-based energy consumption patterns which leads to increased greenhouse gas emissions. Energy availability is important for economic development and improved quality of life, therefore transition to clean renewable energy options is required without compromising on energy availability. According to sustainable development goal number seven, for sustainable and inclusive development it is important to focus on clean and affordable energy for all with consideration for the environment. Here the role of solar energy technologies becomes extremely important, as their carbon footprint is low and can be used for a wide variety of applications. This paper discusses the potential of solar resources for the BRICS countries and the prospective solar thermal and solar PV technologies for each country according to the region-wise resource. BRICS countries represent around 40% of the world's population. The methodology for identifying the prospective solar technologies for the BRICS countries is based on an analysis of the solar resource potential for each country. It is found that all the BRICS countries have good solar potential and can utilize several solar energy technologies to enhance green technology practices. Further, the challenges in the implementation and promotion of solar projects are discussed with suggestions for collaborative research and development in this area. Policy requirements to overcome the limitations of the technologies and their penetration are also pointed out.
- 28 May 2025
- Published by University of Johannesburg in Journal of BRICS Studies
- Vol. 4 (1) , 17-26
Open AccessProspective Solar Energy Technologies for Sustainable and Inclusive Development in BRICS Countries
The climate change scenario observed in the last few years calls for immediate attention and planned action. One of the major factors responsible for climate change is fossil fuel-based energy consumption patterns which leads to increased greenhouse gas emissions. Energy availability is important for economic development and improved quality of life, therefore transition to clean renewable energy options is required without compromising on energy availability. According to sustainable development goal number seven, for sustainable and inclusive development it is important to focus on clean and affordable energy for all with consideration for the environment. Here the role of solar energy technologies becomes extremely important, as their carbon footprint is low and can be used for a wide variety of applications. This paper discusses the potential of solar resources for the BRICS countries and the prospective solar thermal and solar PV technologies for each country according to the region-wise resource. BRICS countries represent around 40% of the world's population. The methodology for identifying the prospective solar technologies for the BRICS countries is based on an analysis of the solar resource potential for each country. It is found that all the BRICS countries have good solar potential and can utilize several solar energy technologies to enhance green technology practices. Further, the challenges in the implementation and promotion of solar projects are discussed with suggestions for collaborative research and development in this area. Policy requirements to overcome the limitations of the technologies and their penetration are also pointed out.
- Open Access
- 28 November 2024
- Published by Elsevier in Solar Compass
- Vol. 12
Experimental study on conversion of blanched grapes to raisins without chemicals through solar dryer to reduce drying time
- 28 November 2024
- Published by Elsevier in Solar Compass
- Vol. 12
Open AccessExperimental study on conversion of blanched grapes to raisins without chemicals through solar dryer to reduce drying time
- Top Cited Papers
- 4 April 2024
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 197
Comprehensive review on agrivoltaics with technical, environmental and societal insights
- 4 April 2024
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 197
Top Cited PapersComprehensive review on agrivoltaics with technical, environmental and societal insights
- 9 June 2022
- Published by Elsevier in Solar Energy
- Vol. 241, 72-84
Review of solar PV training manuals and development of survey based solar PV system training formats for beginners
- 9 June 2022
- Published by Elsevier in Solar Energy
- Vol. 241, 72-84
Review of solar PV training manuals and development of survey based solar PV system training formats for beginners
- 10 February 2022
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 29 (34) , 51153-51160
Development and investigative studies on solar hot case food warmer for food safety at offices/institutes
The paper presents the design, development and investigative studies into the use of a solar hot case/food warmer. The solar hot case can prove to be highly useful to the persons who carry hot food to their workplaces for lunch and eat it 4–5 h later. It can help keep food warm and infection free, by maintaining the food at an elevated temperature. The solar hot case has been developed with a total aperture area of 0.673 m2. The energy requirements for food warming have been calculated and found to be around 62 kJ in summer and 90 kJ in winter for an average lunch box of mass 0.25 kg containing 0.4 kg of food. The design of the solar hot case has been prepared on the basis of the food warming calculations to allow around ten lunch boxes to be warmed simultaneously. A computer program based on the solar radiation geometry and an ASHRAE model has been prepared to study the energy available in various months and to estimate the solar energy interception by the solar hot case. The results show that the energy absorbed by the system at an instant varies from around 300 to 1400 kJ/m2h in winter and 1000–2000 kJ/m2h in summer. Experimental in-field observations related to the temperature profiles of the developed system are also reported.
- 10 February 2022
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 29 (34) , 51153-51160
Development and investigative studies on solar hot case food warmer for food safety at offices/institutes
The paper presents the design, development and investigative studies into the use of a solar hot case/food warmer. The solar hot case can prove to be highly useful to the persons who carry hot food to their workplaces for lunch and eat it 4–5 h later. It can help keep food warm and infection free, by maintaining the food at an elevated temperature. The solar hot case has been developed with a total aperture area of 0.673 m2. The energy requirements for food warming have been calculated and found to be around 62 kJ in summer and 90 kJ in winter for an average lunch box of mass 0.25 kg containing 0.4 kg of food. The design of the solar hot case has been prepared on the basis of the food warming calculations to allow around ten lunch boxes to be warmed simultaneously. A computer program based on the solar radiation geometry and an ASHRAE model has been prepared to study the energy available in various months and to estimate the solar energy interception by the solar hot case. The results show that the energy absorbed by the system at an instant varies from around 300 to 1400 kJ/m2h in winter and 1000–2000 kJ/m2h in summer. Experimental in-field observations related to the temperature profiles of the developed system are also reported.
- Open Access
- 2 September 2019
- Published by European Open Science in European Journal of Engineering and Technology Research
- Vol. 4 (9) , 186-194
Heat Gain Study of a Residential Building in Hot-Dry Climatic Zone on Basis of Three Cooling Load Methods
The paper presents the study on theoretical heat gain for a residential building located in hot-dry climatic zone of India. The location is city Kota (25.100 N, 75.830 E). To determine heat gain, three different methods have been used. The aim of the paper is to study the heat gains and also to compare the three different methods. First method is CLTD/GLF method which is taken from ASHRAE 1997, second method is CLF/SCL/CLTD method which also taken from ASHRAE 1997 and third method is RLF method which is taken from ASHRAE 2013. After that comparative study has been done of all three methods. For the study a typical middle income group residential house has been considered. The model house is taken of size 12 m x 15 m with three windows of size 1 m x 1m each and one door of size 1 m x1.5 m. The walls are brick wall and roof is taken of RCC. From the analysis it is found that CLTD/GLF method predicts heat gain towards lower side whereas CLTD/SCL/CLF method values are higher and RLF values lies in between being more close to CLTD/SCL/CLF method. An important point to notice on comparison of results is that all methods predict around 50% heat gain through roof for this building structure. Another major contribution to heat gain (around 30%) is through walls. The window to wall ratio for the building is 1.9% and therefore the effect of heat gain through windows is only around 8%. Other factors contribute only a minor percentage to the overall heat gain. Thus, from the results it can be concluded that in order to reduce the heat gain and cooling load, major attention must be paid on roof and wall heat gain along with the other factors. Suitable passive measures can be identified on the basis of heat gain study.
- 2 September 2019
- Published by European Open Science in European Journal of Engineering and Technology Research
- Vol. 4 (9) , 186-194
Open AccessHeat Gain Study of a Residential Building in Hot-Dry Climatic Zone on Basis of Three Cooling Load Methods
The paper presents the study on theoretical heat gain for a residential building located in hot-dry climatic zone of India. The location is city Kota (25.100 N, 75.830 E). To determine heat gain, three different methods have been used. The aim of the paper is to study the heat gains and also to compare the three different methods. First method is CLTD/GLF method which is taken from ASHRAE 1997, second method is CLF/SCL/CLTD method which also taken from ASHRAE 1997 and third method is RLF method which is taken from ASHRAE 2013. After that comparative study has been done of all three methods. For the study a typical middle income group residential house has been considered. The model house is taken of size 12 m x 15 m with three windows of size 1 m x 1m each and one door of size 1 m x1.5 m. The walls are brick wall and roof is taken of RCC. From the analysis it is found that CLTD/GLF method predicts heat gain towards lower side whereas CLTD/SCL/CLF method values are higher and RLF values lies in between being more close to CLTD/SCL/CLF method. An important point to notice on comparison of results is that all methods predict around 50% heat gain through roof for this building structure. Another major contribution to heat gain (around 30%) is through walls. The window to wall ratio for the building is 1.9% and therefore the effect of heat gain through windows is only around 8%. Other factors contribute only a minor percentage to the overall heat gain. Thus, from the results it can be concluded that in order to reduce the heat gain and cooling load, major attention must be paid on roof and wall heat gain along with the other factors. Suitable passive measures can be identified on the basis of heat gain study.
- Open Access
- 8 November 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2033 (1) , 130011
Commercial development of bio-combustible fuels from hydrothermal liquefaction of waste using solar collectors
Current methods to improve the viability of microalgae based biofuel production depend on improved microalgae strains, biorefinery concepts and identification of higher value applications such as cosmetics and nutraceuticals. Despite such efforts, the energy inputs into the microalgae conversion process remain high. The technical approach presented is to design, deploy and field test an integrated set-up of Concentrated Solar Power and Hydrothermal Liquefaction systems to produce bio-oil and evaluate the production and conversion processes. Phycofeeds’ approach is to integrate CSP and HTL technologies into the conversion process to improve the energy efficiency and the economic case for scaling microalgae based biofuel production. Further sustainability enhancements are achieved by integrating wastewater feedstock and market integration of output by-products for the aquaculture feed industry. This paper presents the microalgae harvesting and HTL bio-oil formation analysis procedures on a pre-pilot field scale. Solar concentrating captors are described and theoretical values obtained prior to experimental work that will be carried out in India.
- 8 November 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2033 (1) , 130011
Open AccessCommercial development of bio-combustible fuels from hydrothermal liquefaction of waste using solar collectors
Current methods to improve the viability of microalgae based biofuel production depend on improved microalgae strains, biorefinery concepts and identification of higher value applications such as cosmetics and nutraceuticals. Despite such efforts, the energy inputs into the microalgae conversion process remain high. The technical approach presented is to design, deploy and field test an integrated set-up of Concentrated Solar Power and Hydrothermal Liquefaction systems to produce bio-oil and evaluate the production and conversion processes. Phycofeeds’ approach is to integrate CSP and HTL technologies into the conversion process to improve the energy efficiency and the economic case for scaling microalgae based biofuel production. Further sustainability enhancements are achieved by integrating wastewater feedstock and market integration of output by-products for the aquaculture feed industry. This paper presents the microalgae harvesting and HTL bio-oil formation analysis procedures on a pre-pilot field scale. Solar concentrating captors are described and theoretical values obtained prior to experimental work that will be carried out in India.